Manuale d’uso / di manutenzione del prodotto P42V6-A8K del fabbricante Haier
Vai alla pagina of 47
Please READ this manual carefully before operating your TV, and retain it for future reference. PLASMA TV OWNER`S MANUAL MODEL : P42V6-A8K P42V6-A8 S.
Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. T o prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product.
1. Retain these Instructions ---the safety and operating instructions should be retained for Future reference. 2. Heed Warnings ---All warning on the appliance and in the operating instructions should be followed. 3. Cleaning --- Unplug from the wall outlet before cleaning.
a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have been fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions.
T able of Contents Warning Important Safety Instructions.............. Buttons and interface location............ .......................... .................... .............................. .................... Function introduction Effective range External Equipment Connections .
Front control panel -This is a simplified representation of front panel. -Here shown may be somewhat dif ferent from your TV. Buttons and interface location 1. Remote control signal receive window 2. Remote indicator : in red when standby mode 3. MENU : menu display 4 .
Buttons and interface location Rear Control panel ANT IN HDMI/DVI VIDEO VGA AUDIO DVI IN AUDIO VGA IN COMPONENT IN Pr/Cr Pb/Cb Y L-AUDIO-R AUDIO OUT L R SCART2 SCART1 Rear Control panel 1. AUDIO OUT : 2.VGA IN(PC) Connect VGA analog cable from the PC to the VGA IN.
Remote controller Precautions 3 .Replace the cover of the battery compartment. Make sure that there is no obstacle between the remote controller and television set. As strong light may interfere the signals, change your position to operate the remote controller if the television cannot be turned on or of f as you expect.
STILL SLEEP PIP TV/A V P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLA Y CH+ CH- VOL- VOL+ MENU Keys of remote controller STILL Picture static I/II (NICAM) MUTE Switches the sound on or of f Power Off/Standby any other programmed equipment off.
STILL SLEEP PIP TV/AV P.STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU Ensure the remote controller is pointed toward the remote controller window on t he display .
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different. Mixer additional purchase Note * It is recommended that you'd better use 75 * Don't bind antenna cable and electric wire together .
ANT IN COMPONENT IN Pr/Cr Pb/Cb Y L-AUDIO-R SCART2 SCART1 External Equipment Connection - T o avoid picture noise (interference), leave an adequate distance between the VCR And TV. VCR connection NOTE: All cables shown are not included with the TV . 1.
HDMI/DVI OUTPUT R AUDEO L RGB-DTV OUTPUT R AUDEO L YP bP r R AUDEO HDMI/DVI VIDEO VGA AUDIO DVI IN AUDIO VGA IN COMPONENT IN Pr/Cr Pb/Cb Y L-AUDIO-R ANT IN COMPONENT IN Pr/Cr Pb/Cb Y L-AUDIO-R SCART2 SCART1 How to connect 1 .
VGA AUDIO VGA IN AUDIO OUT L R How to connect 1 . T o get the best picture quality , adjust the PC graphics card to ( 1024 2 . Use the TV`s VGA port for video connections, depending on your PC connector .
Power source TO USE A C POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet. NOTES: Never connect the AC line cord plug to other than the specified voltage. Use the attached power cord only.
Switching ON/OFF the TV set 1 Please press down the power switch to switch on AC power supply and the power indicator will light . 2 If the indicator is lighting in red, press button on the remote controller again. 3 If you want to exchange to standing by status, please press down button on the remote controller .
STILL SLEEP PIP TV/AV P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU Choose the input source Press INPUT or TV/AV button on television or remote controller , the menu appears on the screen.
STILL SLEEP PIP TV/AV P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU This TV set has three methods to set channels, which are respectively full a utomatic, manual s earch fine tune.
Tuning menu Program T able STILL SLEEP PIP TV/AV P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU 1 Press MENU button and t hen C H+/- b utton, the i con to TUNING menu.
Manual search If excessive channel signals of unwanted programs are received in local area, manual search function is recommended. 1 Press C H+/- buttons or the NUMBER 0-9 button t o choose desired searching f requency . (regard channel 18 as example).
STILL SLEEP PIP TV/AV P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU Fine Tuning If the picture and/or sound are poor, try using the FINE TUNING feature. Do not use this feature unless reception is poor.
You can watch TV program in a presetting channel. How to select the desired program 1 Using "Program number" buttons . Press digit button to select the program.
If the colour of some channel is abnormal Usually this should be set in the auto position. However if the colour displayed on the screen are incorrect, you can manually select the correct colour system. Press the CH+/- button to select ound System", then press the VOL-/+ button to select the correct sound system.
3 . press VOL-/+ button to set Skip On . And press menu exit. After the programs are presetting, you can skip some programs so that to select your favorite channels only. 1 . Press CH+/- button or Direct-digit Choosing button to select a channel directly (take channel 18 for example).
Picture menu How to customize your own picture status Brightness Contrast Sharpness Saturation Hue (only in NTSC mode) Dark Weak Soft Shallow color More purple Bright Strong Sharp Deep color More green How to select picture modes You can quickly select the desired picture mode from three preset modes and one customized mode.
Noise Reduction 1 Afte r cal ling up th e Picture menu, press CH+/- button to s elect item. "Noise Reduction" 2 Press VOL+ to e nter the l ist. S elect Off , Auto Weak according to th e im age noise. , Me dium or Strong 3 Press MENU return to the picture menu.
To choose sound modes Press the S.STD button to call up Audio mode menu, and press CH+/- button to select the desired sound quality. Four kinds of sound models (i.
STILL SLEEP PIP TV/AV P .STD S.STD H.LOCK CH.LIST EXIT SCAN SWAP TIMER ZOOM ABC@ DEF JKL% GHI$ MNO STUV POR& WXYZ *#() MUTE DISPLAY CH+ CH- VOL- VOL+ MENU Setting Five Equalizer sound 1 Press MENU button and then C H+/- b utton to sel ect AUDIO menu.
When you need to pay attention to surrounded sounds, or there is a telephone calling you or there are some guests visiting you, the sound elimination (mute) function is very convenient. How to eliminate sound 1 Press the MUTE button on the remote control and "Mute" type face will display on the lower part of the screen.
Timer setting 2 Press CH+/- button select "Timer", press VOL -/+ buttons to select hour or minute position; then press digits buttons to set the value of hour or minute; 3 Press MENU button to return the previous menu. The clock will only work if the TV set is turned on or in standby .
On/off timer Timer on Prog Timer Prog 1 Press MENU and VOL+/- button to call up the TIMER menu on the screen. 2 Press CH+/- button to select " Time On ", press VOL-/+ buttons to select hour or minute position; then press digits buttons to set the value of hours or minutes.
It is possible to select language, OSD transparent, position and screen display of the menu as follows: Function menu 1 . Press MENU button once, and the CH+/- button until the following menu appears on the screen: OSD language option Repeat step 3 and 4 to select the language you wanted from the 13 kinds of languages.
2005-01-01 Sun. Mon. Tue . Wed. Thu. Fri. Sat. 1 8 7 6 5 4 3 2 15 22 29 14 21 28 13 20 27 12 19 26 11 18 25 10 17 24 31 9 16 23 30 Function menu Calendar display and check Repeat step 3 and 4 to enter Calendar menu as follows: Press VOL+/- to select among year , month and day, and then CH+/- to adjust them.
To choose picture aspect ratio Normal 4:3 Mode Press ZOOM button to select the desired picture ratio. Three kinds of models (i.e., Wide Screen and 4:3 Mode ) can be selected in turn.
VGA, HDMI: AUDIO ADJUST TUNING FUNCTION TIMER MENU PICTURE Display Mode Adjust RGB Default Auto Sync Color Temperature Black Stretch Off Normal Normal In VGA and HDMI input mode, H-Position and V-Position can be adjusted to eliminate transverse line interference and decentered picture as follows: 1 .
1) RGB is opted for adjustment of the numerical value of red, green and blue in VGA,HDMI mode. 2) Default is opted for adjustment of parameters to delivery setup in VGA mode.(After the operation, complete will be on the right of the operation) 3) Auto Sync is opted for adjustment of picture location frequency and phase parameters in VGA mode.
Press H.LOCK button, Password will appear on the screen. The initial password of the television is 0000 and security default password is 9443. then enter Lock Set menu.(as follow) The television has the function of security default lock. Password needs to be entered when the program lock mode is to be set.
Prog Num Prog Num is opted for setting up preset channel. Press CH+/- button to select Prog Num. Press VOL /- button, to select channel number.(The item is not available except TV signal.) Source Lock Source Lock is opted to hinder external input modes, such as AV , Scart and VGA.
Max Volume Press CH+/- button to select Max Volume. Press VOL+/- button for adjustment between 0 100. If a certain value is set, when volume is being adjusted, the sound value can not exceed maximum volume value. If current volume is over Max V olume, when Lock Set menu is set, current volume will become set maximum volume.
Others functions Display function NICAM If the broadcaster is transmitting Bilingual sound service. The button on the remote controller will allow up to 2 separate languages to be selected.
Sleep 1 . Press SLEEP button repeatedly to select the number of preset minutes, the timer will be set in sequence: 0Min 5Min 15Min 30Min 60Min 90Min 120Min 0Min 2 . A fter the sleep time is set, the Indication will appear on the screen 1minute prior to expiry of set time.
Teletext is an information system, broadcast by certain channels, which can be read like a newspaper . It also provides subtitles for people with hearing difficulties or those who are unfamiliar with the language in which a particular programme is being broadcast (cable networks, satellite channels, etc.
(MIX) While in T eletext mode press the button will show the teletext data superimposed on top of the TV picture. Press the button again to revert back to Full text. (HOLD) Pressing the button will stop the teletext page automatically updating. This feature is very useful where there are several teletext pages or data on the same page number .
To remove dirt or dust, wipe the cabinet with a soft, dry , lint-free cloth. Please be sure not to use a wet cloth. Maintenance Cleaning the Screen - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV.
Specifications and functions P42V6-A8K Screen Type Viewing angle Diagonal Color system Sound system Video input TV/VIDEO DTV YCbCr YPbPr PLASMA DISPLA Y P ANEL >170 (H)/170 (V) PAL, SECAM, NTSC-M D.
Troubleshooting For the sake of time and cost, it is strongly recommended that you check out the problem by yourself according to the instructions listed hereunder before contacting the after-sales service for technical assistance. Note : Production of the plasma screen requires high and precision technologies.
0090506943C 01.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Haier P42V6-A8K è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Haier P42V6-A8K - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Haier P42V6-A8K imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Haier P42V6-A8K ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Haier P42V6-A8K, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Haier P42V6-A8K.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Haier P42V6-A8K. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Haier P42V6-A8K insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
