Manuale d’uso / di manutenzione del prodotto AD1686B del fabbricante American Dynamics
Vai alla pagina of 28
Model AD1686B General Purpose Indoor/Outdoor Receiver Installation and Operating Instructions This manual describes the installation and operating procedures for the AD1686B Dual Channel Receiver. Receivers are designed as the remote control device for operation of a motorized pan and tilt unit and a motorized lens unit.
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION............................................................................... 1 FEA TURES ..................................................................................... 1 Pan/T ilt and Lens Control ...................
.
AD1686B DESCRIPTION and FEATURES DESCRIPTION The AD1686B Receiver is a 2-channel controller used with Matrix Switching Systems to control pan, tilt, zoom, focus, iris, and auxiliary functions at a camera site. This Receiver is classified as a dual-channel type since two independent control channels are supplied, Channel A and Channel B.
SETUP AD1686B 2 SETUP Pan/Tilt Output Voltage The Pan/Tilt output voltages of each channel can be independently set for either 24 VAC or line voltage (120VAC or 230VAC). Two slide switches, S4 and S5 (see Figure 1), control the output voltages for the channels.
Table 2 - S3 Configuration Select Receiver Configuration Switch S3 general description is listed below. This table is continued on page 4 to describe the switch settings in detail, with a list of individual switch position settings.
Table 2 - S3 Configuration Select (Continued from page 3) L = left ("off"); R = right ("on") SW1 - Channel B Type - The AD1686B can act as a dual camera receiver with no auxiliaries, or as a single camera receiver with a set of auxiliaries.
AD1686B SETUP 5 Table 3 - S1 Camera Number Switch Settings - Channel A L = left ("off"); R = right ("on") CAMERA Switch Position CAMERA Switch Position NUMBER 1 2 3 4 5 6 NUMBER 1 .
SETUP AD1686B 6 Table 4 - S2 Camera Number Switch Settings or Auxiliary Settings Channel B L = left ("off"); R = right ("on") CAMERA Switch Position CAMERA Switch Position NUMBER 1.
INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes.
CONNECTIONS Code Line Connections The AD Code Line connection to the Receiver is made with user-supplied, shielded 2-wire twisted pair, Belden 8760 or equivalent (for Plenum use Belden 88760 or equivalent).
AD1686B CONNECTIONS Pan/Tilt and Lens Connections The AD1686B Receiver connection to a Pan/Tilt and a motorized Lens is with a 12-pin connector. This connector, for Channel A, is located on the main PCB, to the right of the DIP switches S1 and S2, and is labeled J5 (see Figure 1, page 3).
CONNECTIONS AD1686B 10 Table 5 - Dual Pan/Tilt and Lens 12-pin Connector Pinout Channel A - J5 PIN No. FUNCTION Pan/Tilt PINOUT LENS PINOUT 01 Tilt Up _____________________ ____________________ 02 Til.
AD1686B CONNECTIONS Auxiliary Connections When the AD1686B Receiver is set for single camera operation with auxiliaries, connection of auxiliary equipment to Channel B is made to the 12-pin connector, labeled J4, located on the Receiver PCB. See Figure 1, page 3.
Pre-position (Preset) Connections The AD1686B Receiver connection to the Pan/Tilt and Lens pre-position servo unit is with a 9-pin connector labeled J2 (see Figure 1, page 3). For dual camera channel operation, a second 9-pin connector, labeled J3, is used for Channel B.
AD1686B CONNECTIONS 13 Table 7 - Pre-position Pan/Tilt and Lens 9-pin Connector Pinout Channel A - J2 PIN No. FUNCTION Pan/Tilt PINOUT LENS PINOUT 01 (+) REF _____________________ ____________________.
CONNECTIONS AD1686B Power Input Connections Refer to the instructions provided with the enclosure for suitable conduit connectors (when required), and mounting and caution information. Two type PG-16 liquid tight fittings are supplied for use with cord diameters from .
TYPICAL SYSTEM CONNECTIONS.
TYPICAL SYSTEM CONNECTIONS AD2150 Controller to AD1686B MAXIMUM DISTANCE between AD1686B and AD2150 is 5000 Ft, using shielded, 18 AWG cable AD2150 AD1686B BWS RS232 PORTS 123 KEYBOARDS 2345 CAMERAS A.
TYPICAL SYSTEM CONNECTIONS AD1996 Controller to AD2091 Code Generator, to AD1686B AD1686B AD2091 AD1996 ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF B W S B W S B W S B W S B W S B W S B W .
TYPICAL SYSTEM CONNECTIONS AD1686B to AD1240P Pan/Tilt with Pre-position AD1686B 1240P PAN/TILT C-4 Code PWR F2 F1 S5 S4 24V 120V 24V 120V J2 J5 J3 J4 S3 8 1 OFF ON S1 6 1 S2 6 1 W S B J6 AD1240P 13-pin Connector, Pan/Tilt pins: 1. PAN/TILT COMMON 2. PAN RIGHT 3.
INDEX.
INDEX AD1686B Auto and Random Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Auxiliaries Configuration Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
SPECIFICATIONS Supply Voltage: AD1686B 120 VAC, 50/60 Hz AD1686B-X 230 VAC, 50 Hz Power: 30 W (standby) AD1686B: 1240 W maximum input @ 120 VAC AD1686B-X 1420 W maximum input @ 230 VAC Mounting: Surface Mount Size: 15.5" H x 12.8" W x 6.7" D (394 x 325 x 170 mm) Weight: 16 lbs.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il American Dynamics AD1686B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del American Dynamics AD1686B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso American Dynamics AD1686B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul American Dynamics AD1686B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il American Dynamics AD1686B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del American Dynamics AD1686B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il American Dynamics AD1686B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo American Dynamics AD1686B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
