Manuale d’uso / di manutenzione del prodotto AD1676B del fabbricante American Dynamics
Vai alla pagina of 20
This manual describes the installation and operating procedures for the American Dynamics 1676B Series Operator Keyboards. The 1676B Series keyboards are used with the following matrix switching systems: the 1650B MicroPower, the 2050 MegaPower II, the 2150 System V, and the 2350 systems.
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301C Warning: This product generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
T able of Contents General Description .............................................................. 1 Keyboard Connections ......................................................... 2 Junction Box Mounting ............................................
GENERAL DESCRIPTION The 1676 Series keyboards are used for full function control with the following matrix switching systems: the 1650B MicroPower, the 2050 MegaPower II, the 2150 System V, and the 2350 System.
KEYBOARD CONNECTIONS The 1676 keyboard is supplied with a wall-mount transformer (7.5 VAC), part number TP8059, a seven-foot 8-pin modular cable, part number JJ0007, and an 8-pin modular junction box, part number HP0047. The 8-pin modular format is commonly referred to as a RJ-45.
To connect the 1676 keyboard to a particular switching system, refer to the following steps and the illustrations contained in the Appendices. a) For 1650B Systems see Appendix A. b) For 1996 CPU (2050 Systems) see Appendix B. c) For 2150/2350 Systems see Appendix C.
KEYBOARD SETUP The 1676 keyboard is designed to control a maximum of five contiguous monitors. The number of monitors controlled by the keyboard is set using a DIP switch located on the under side of the unit (see Figure 3, below). By selecting the appropriate combination (shown in Table 4), the keyboard can control either 1, 2, 3, or 5 monitors.
Base Monitor Number Selection The selection of the starting monitor for the group uses S1, S2, S3, S4, S5, and S6 of the DIP switch. The monitor number is selected on the DIP switches by calculating the monitor number in binary, minus 1. This allows the keyboard to be programmed for access to different groups of monitors.
KEYBOARD OPERATION Keyboard control of system functions is "monitor oriented" in that a keyboard controls only those system functions associated with the display on the monitor to which it is "connected". System monitors not under keyboard control continue to operate in whatever state they were left.
Pan/Tilt, Lens, and Auxiliary Control When called on-screen, cameras at sites equipped with 1680 and/or 1640 Series Receivers are controlled as follows: Pan and Tilt - Hold the joystick in the direction you wish to move the camera. The camera will continue to move until the joystick is centered.
.
APPENDIX.
.
TYPICAL SYSTEM CONNECTIONS 1676 TO 1650 NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE. 1650A/1650B A 1 2 3 45 6 7 8 1 2 3 45 6 7 8 O U T O U T MONITOR 21 A A B .
NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE. 1996 B TYPICAL SYSTEM CONNECTIONS 1676 TO 1996 1 2 3 45 6 7 8 RED GREEN BROWN THREE CONDUCTOR SHIELDED BELDEN 8770 OR EQUIVALENT TP8059 7.
NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE. 2150/2350 C TYPICAL SYSTEM CONNECTIONS 1676 TO 2150/2350 RS232 PORTS MONITORS 12 3 45 12 3 ALARMS RELAY KEY.
D TYPICAL SYSTEM CONNECTIONS 1676 TO 1981 Port Expander 1996 12 34 5 678 9 10 PROG MON DATA LINE PORTS 12 120V 60HZ To CPU KBD d KBD c KBD b KBD a 1 2 3 45 6 7 8 12 345 67 8 9 12 345 67 8 9 12 345 67 .
.
An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965 (914) 624-7600 Technical Support Center 1-800-442-2225 FAX: 914-624-7685 8000-0884-01 OP1676BC June 1996 Printed in USA Specifications SIZE: 3.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il American Dynamics AD1676B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del American Dynamics AD1676B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso American Dynamics AD1676B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul American Dynamics AD1676B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il American Dynamics AD1676B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del American Dynamics AD1676B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il American Dynamics AD1676B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo American Dynamics AD1676B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
