Manuale d’uso / di manutenzione del prodotto GA-880GM-USB3 del fabbricante Gigabyte
Vai alla pagina of 100
GA-880GM-USB3 User's Manual Rev . 3101 12ME-88GMUB3-3101R.
Motherboard GA-880GM-USB3 Mar . 5, 2011 Mar. 5, 201 1 Motherboard GA-880GM-USB3.
Copyright © 201 1 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE.
- 4 - T able of Contents Box Contents ................................................................................................................... 6 Optional Items ................................................................................
- 5 - Chapter 3 Drivers Installation ........................................................................................ 57 3-1 Installing Chipset Drivers ............................................................................... 57 3-2 Application Software .
- 6 - Box Contents GA-880GM-USB3 motherboard Motherboard driver disk User's Manual Quick Installation Guide T wo SA T A 3Gb/s cables I/O Shield Optional Items 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R) 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R) 2-port SA T A power cable (Part No.
- 7 - GA-880GM-USB3 Motherboard Layout KB_MS_USB CPU_F AN A TX GA-880GM-USB3 F_AUDIO AUDIO SPDIF_OUT PCIEX1 DDR3_1 DDR3_2 A TX_12V_2X4 AMD 880G AMD SB710 SA TA2_3 SA TA2_0 SA TA2_4 SA TA2_2 SA TA2_1 P.
- 8 - GA-880GM-USB3 Motherboard Block Diagram (Note 1) T o reach DDR3 1800 MHz or above, you must install two memory modules and install them in the DDR3_3 and DDR3_4 memory sockets. (Note 2) Simultaneous output for DVI-D and HDMI is not supported. Hyper T ransport 3.
- 9 - Hardware Installation 1- 1 Installation Precautions Th e m ot her bo ar d c on ta in s n um er ou s d el ic at e e le ct ro ni c c ir cu it s a nd comp one nt s w hi ch can become damaged as a result of electrostatic discharge (ESD).
Hardware Installation - 10 - 1- 2 Product Specications CPU AM3+ Socket: - AMD AM3+ processor - AMD AM3 Phenom ™ II processor/ AMD Athlon ™ II processor (Go to GIGABYTE's website for the latest CPU support list.) Hyper Transport Bus 520 0 MT/s Chipset North Bridge: AMD 880G South Bridge: AMD SB710 Memory 4 x 1.
- 1 1 - Hardware Installation USB South Bridge: - Up to 10 USB 2.0/1.1 ports (4 on the back panel, 6 via the USB brackets connected to the internal USB headers) Etron EJ168 chip: - Up to 2 USB 3.
Hardware Installation - 12 - BIOS 2 x 16 Mbit ash Use of licensed AW ARD BIOS Support for DualBIOS ™ PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.
- 13 - Hardware Installation 1-3 Installing the CPU and C PU Cooler 1-3 -1 I nst all ing t he CPU A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU. Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU.
Hardware Installation - 14 - B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. • Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.
- 15 - Hardware Installation 1-3 -2 I nst all ing t he CPU Cool er Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU.
Hardware Installation - 16 - 1- 4 Installing the Memor y DDR3_1 DDR3_2 DDR3_3 DDR3_4 Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory . It is recommended that memory of the same capacity , brand, speed, and chips be used.
- 17 - Hardware Installation 1- 4 -2 Inst all ing a M emo r y Notch Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs.
Hardware Installation - 18 - 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
- 19 - Hardware Installation 1-6 Setup of the A TI Hybrid CrossF ireX ™ Conguration Combining the onboard GPU with a discrete graphics card, A TI Hybrid CrossFireX can provide signicantly advanced display performance for AMD platform. Read the following instructions on conguring an A TI Hybrid CrossFireX system.
Hardware Installation - 20 - 1- 7 Back Panel Con nectors In Windows Vista, select Start>Control Panel>Sound, select Realtek HDMI Output and then click Set Default . (Note 1) The DVI-D port does not support D-Sub connection by adapter. (Note 2) Simultaneous output for DVI-D and HDMI is not supported.
- 21 - Hardware Installation A. Dual Display Congurations: This motherboard provides three ports for video output: DVI-D, HDMI and D-Sub. The table below shows the supported dual display congurations.
Hardware Installation - 22 - In addition to the default speak ers settings, the ~ audio jacks can be recongured to perform differe nt fun ctio ns via the au dio so ftwa re. On ly mic roph ones s till M UST be co nnect ed to t he default Mic in jack ( ).
- 23 - Hardware Installation 1-8 Internal Connec tors Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. • Befor e ins tall ing th e dev ices, be sur e to tu rn off th e devi ces a nd you r com puter.
Hardware Installation - 24 - DEBUG PO RT G.QBOFM A TX_12V_2X4 4 1 8 5 1/2) A TX_12V_2X4/A TX (2x4 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the com- ponents on the motherboard.
- 25 - Hardware Installation 3/4) CPU_F AN/SYS_F AN (Fan Headers) The motherboard has a 4-pin CPU fan header (CPU_F AN)and a 4-pin system fan header(SYS_F AN). Each fan header supplies a +12V power voltage and possesses a foolproof insertion design. When con- necting a fan cable, be sure to connect it in the correct orientation.
Hardware Installation - 26 - 6) SA T A2_0/1/2/3/4 (SA T A 3Gb/s Connectors, Controlled by AMD SB710 South Bridge) The SA T A connectors conform to SA T A 3Gb/s standard and are compatible with SA TA 1.5Gb/s standard. Each SA T A connector supports a single SA TA device.
- 27 - Hardware Installation 8) F_P ANEL (Front Panel Header) Co nnect the pow er swi tch, r eset s witch , spea ker, ch assi s intr usion switc h/sen sor an d syst em stat us indicator on the chassis to this header according to the pin assignments below.
Hardware Installation - 28 - 9) F_AUDIO (Front Panel Audio Header) The fron t panel audio header supports Intel Hig h Denition audio (HD) and AC'97 audio. Y o u may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module con - nector match the pin assignments of the motherboard header.
- 29 - Hardware Installation 1 1) F_USB1/F_USB2/F_USB3 (USB Headers) The headers conform to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer .
Hardware Installation - 30 - 13) COM (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the op- tional COM port cable, please contact the local dealer .
- 31 - BIOS Setup BIOS (Ba sic Inpu t and Out put Syst em) reco rds hard ware par ameters of the sy stem in t he CMOS o n the motherboard. Its major functions include conducting the Power-On Self-T est (POST) during system startup, saving sy stem param eters and l oading op erating sy stem, etc .
BIOS Setup - 32 - Motherboard Model BIOS V ersion Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-201 1, Award Software, Inc. GA-880GM-USB3 DE .
- 33 - BIOS Setup Function Keys: <T AB>: POST SCREEN Press the <T ab> key to show the BIOS POST screen. T o show the BIOS POST screen at system start- up, refer to the instructions on the Full Screen LOGO Show item on page 45.
BIOS Setup - 34 - 2-2 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use ar- row keys to move among the items and press <Enter> to accept or enter a sub-menu.
- 35 - BIOS Setup The Functions of the <F1 1> and <F12> keys (For the Main Menu Only) F1 1: Save CMOS to BIOS This function allows you to save the current BIOS settings to a prole. Y ou can create up to 8 proles (Prole 1-8) and name each prole.
BIOS Setup - 36 - 2-3 MB Intelligent T weaker(M.I.T .) • Whether the system will work stably with the overclock/overvoltage settings you made is depen - dent on your overall system congurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components.
- 37 - BIOS Setup CMOS Setup Utility-Copyright (C) 1984-2011 A ward Software IGXConguration higf : Move Enter: Select +/-/PU/PD: V alue F10: Save ESC: Exit F1: General Help F5: Previous V alues .
BIOS Setup - 38 - CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being used. CPU NorthBridge Freq. Allows you to alter the North Bridge controller frequency for the installed CPU.
- 39 - BIOS Setup DCT s Mode Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. (Default) DDR3 Timing Items Manual allows all DDR3 Timing items below to be congurable.
BIOS Setup - 40 - ******** System V oltage Optimized ******** System V oltage Control De ter min es wh eth er to m anu all y set t he sy ste m vol tag es. Auto l ets t he BI OS au tom ati call y set the system voltages as required. Manual allows all voltage control items below to be congurable.
- 41 - BIOS Setup Date (mm:dd:yy) Sets the system date. The date format is week (read-only), month, date and year . Select the desired eld and use the up arrow or down arrow key to set the date. Time (hh:mm:ss) Sets the system time. For example, 1 p.
BIOS Setup - 42 - Halt On Allows you to determine whether the system will stop for an error during the POST . All Errors Whenever the BIOS detects a non-fatal error the system boot will stop. No Errors The system boot will not stop for any error. All, But Keyboard The system boot will not stop for a keyboard error but stop for all other errors.
- 43 - BIOS Setup 2-5 Advanced BIOS Features IGX Conguration The settings in this submenu are synchronous to those under the same items on the MB Intelligent T weaker(M.I.T .) main menu. AMD C1E Support Enables or disables the C1E CPU power-saving function in system halt state.
BIOS Setup - 44 - (Note) This item is present only when you install a CPU that supports this feature. Virtualization Virtualization allows a platform to run multiple operating systems and applications in independent parti- tions. With virtualization, one computer system can function as multiple virtual systems.
- 45 - BIOS Setup HDD S.M.A.R.T . Capability Enables or disables the S.M.A.R.T . (Self Monitoring and Reporting T echnology) capability of your hard drive. This feature allows your system to report read/write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed.
BIOS Setup - 46 - 2-6 Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2011 A ward Software Integrated Peripherals OnChipSA T A Controller [Enabled] OnChipSA T A .
- 47 - BIOS Setup Port0 as ESP/Port1 as ESP/Port2 as ESP/Port3 as ESP This option is congurable only when OnChip SA T A T ype is set to AHCI . Enabled will speed up the hot plug detection of the connected SA T A device.
BIOS Setup - 48 - Start detecting at Port..... LinkDetected-->100Mbps CableLength= 30m Link Detected Displays transmission speed.
- 49 - BIOS Setup ACPI Suspend T ype Species the ACPI sleep state when the system enters suspend. S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode.
BIOS Setup - 50 - (Note) Supported on Windows 7/Vista operating system only . HPET Support (Note) Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system. (Default: Enabled) Power On By Mouse Allows the system to be turned on by a PS/2 mouse wake-up event.
- 51 - BIOS Setup PCI1 IRQ Assignment Auto BIOS auto-assigns IRQ to the rst PCI slot. (Default) 3,4,5,7,9,10,1 1,12,14,15 Assigns IRQ 3,4,5,7,9,10,1 1,12,14,15 to the rst PCI slot. PCI2 IRQ Assignment Auto BIOS auto-assigns IRQ to the second PCI slot.
BIOS Setup - 52 - Hardware Thermal Control Enables or disables the CPU overheating protection function. When enabled, the CPU core voltage and ratio will be reduced when the CPU is overheated. (Default: Enabled) Reset Case Open Status Keeps or clears the record of previous chassis intrusion status.
- 53 - BIOS Setup CPU Smart F AN Control Enables or disables the CPU fan speed control function. Enabled allows the CPU fan to run at different speed according to the CPU temperature. Y ou can adjust the fan speed with EasyTune based on system requirements.
BIOS Setup - 54 - Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard.
- 55 - BIOS Setup Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. Y ou will be requested to conrm the password.
BIOS Setup - 56 - Press <Enter> on this item and press the <Y> key . This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-13 Save & Exit Setup Press <Enter> on this item and press the <Y> key.
- 57 - Drivers Installation 3-1 Installing Chipset Drivers Chapter 3 Drivers Installation After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers that are recommended to install.
Drivers Installation - 58 - 3-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software.
- 59 - Drivers Installation 3-4 Contact For the detailed contact information of the GIGABYTE T aiwan headquarter or worldwide branch ofces, click the URL on this page to link to the GIGABYTE website. 3-5 System This page provides the basic system information.
Drivers Installation - 60 - 3-6 Download Center T o update the BIO S, drivers, or applications, click the Download Ce nter button to link to t he GIGABYTE website.
- 61 - Unique Features 4-1 Xpress Recovery2 Chapter 4 Unique Features Xp r es s R e co v er y 2 i s a u ti l it y t h at a l l ow s y ou to q u ic k l y co m p re s s an d back up your system data and perform restoration of it.
Unique Features - 62 - Step 3: Wh e n pa r ti t io n in g y o ur h a rd d r i ve , m ak e s ur e t o leave unallocated space (10 GB or more is recom- mended; actual size requirements vary , depending on the amount of data) and begin the installation of the operating system.
- 63 - Unique Features D. Using the Restore Function in Xpress Recovery2 E. Removing the Backup F . Exiting Xpress Recovery2 Sel ec t RESTORE to re st or e th e ba ck up t o yo ur h ar d dr ive in case the system breaks down. The RESTORE option will not be present if no backup is created before.
Unique Features - 64 - 4-2 BIOS Update Utilities GI GA B YT E m ot h er b oa r ds p r ov i de t w o un i qu e B IO S u pd a te t o ol s , Q- F la s h ™ an d @ BI O S ™ . GI G AB Y TE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mod e.
- 65 - Unique Features B. Updating the BIOS When updatin g the BIOS, ch oose the loc ation where t he BIOS le is saved. The followi ng procedure as - sumes that you save the BIOS le to a USB ash drive. Step 1: 1. Insert the USB ash drive containing the BIOS le into the computer .
Unique Features - 66 - Step 4: Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see the new BIOS version is present on the POST screen. Step 5: During the POST , press <Delete> to enter BIOS Setup.
- 67 - Unique Features 4-2-2 Updating the BIOS with the @BIOS Utility A. Before Y ou Begin 1. In Windows, close all applications and TSR (T erminate and Stay Resident) programs.
Unique Features - 68 - 4-3 EasyT une 6 GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to ne-tune their system settings or do overclock/overvoltage in Windows environment.
- 69 - Unique Features 4-4 Easy Energy Saver GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with a click of the button.
Unique Features - 70 - C. Stealth Mode In Stealth Mode, the system continues t o work with the user-dened power saving settings, even after the system is restarted. Re-enter the application only if you want to make any changes or completely close the application.
- 71 - Unique Features 4-5 Q-Share Q-Share is an easy and convenient data sharing too l. After conguring your LAN connection settings and Q-Share, you are able to share your data with computers on the same network, making full use of Internet resources.
Unique Features - 72 - 4-6 SMART Recovery With SMART Recovery , users can quickly create backups of changed data les (Note 1) or copy les from a spe - cic backup on P A T A and SA T A hard drives (partitioned on NTFS le system) in Windows Vista.
- 73 - Unique Features 4-7 Auto Green Auto Green is an easy-to-use tool that provides users with simple options to enable system power savings via a Bluetooth cell phone. When the phone is out of the range of the computer's Bluetooth receiver , the sys- tem will enter the specied power saving mode.
Unique Features - 74 - 4-8 Cloud OC Cloud OC (Note 1) is an easy-to-use overclocking utility designed for system overclock- ing via virtually any Internet-conn ected device, such as a smart pho ne, iPhone, note - book PC, etc.
- 75 - Appendix Chapter 5 Appendix 5-1 Conguring SA T A Hard Drive(s) T o congure SA T A hard drive(s), follow the steps below: A. Install SA T A hard drive(s) in your computer . B. Congure SA T A controller mode in BIOS Setup. C. Congure a RAID array in RAID BIOS.
Appendix - 76 - B. Conguring SA T A controller mode in BIOS Setup Make sure to congure the SA T A controller mode correctly in system BIOS Setup. Step 1: Turn on your comp uter an d press < Delete> to enter BIOS Setu p durin g the POS T (Power-On Self-T est).
- 77 - Appendix C. Conguring RAID set in RAID BIOS Enter the RAID BIOS setup utility to congure a RAID array . Skip this step and proceed with the installation of Windows operating system for a non-RAID conguration.
Appendix - 78 - Create Arrays Manually T o create a new array , press <2> to enter the LD View Menu window (Figure 4). T o create an array, press <Ctrl+C> to access the LD Dene Menu . In the LD Dene Menu , use the up or down arrow key to move to an item for further conguration (Figure 5).
- 79 - Appendix In the following procedure, we'll create RAID 0 as an example. 1. Under the RAID Mode section, press the <SP ACE> key to select RAID 0 . 2. Set the Stripe Block size. 64 KB is the default. 3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive.
Appendix - 80 - Delete an Array The Delete Array menu option allows for deletion of disk array assignments. Deleting an existing disk array could result in loss of data. Record all array information including the array type, the disk members, and stripe block size in case you wish to undo a deletion.
- 81 - Appendix 5-1-2 Installing the SA T A RAID/AHCI Driver and Operating System With the correct BIOS settings, you are ready to install Windows 7/Vista/XP onto your hard drive(s). A. Installing Windows XP T o install Windows XP , you need to install the SA T A RAID/AHCI controller driver during the OS installation.
Appendix - 82 - B. Installing Windows 7/Vista The procedure below assumes that only one RAID array exists in your system. Step 1: Restar t your s ystem to boot f rom th e Windo ws 7 set up disk and per form st andar d OS ins tallat ion st eps.
- 83 - Appendix Step 3: When a screen as shown in Figure 4 appears, select AMD AHCI Compatible RAID Controller and click Next . Step 4: After the driver is loaded, the RAID drive will appear . Select the RAID drive and then click Next to continue the OS installation (Figure 5).
Appendix - 84 - Rebuilding an Array: Rebuilding is the process of restoring data to a hard drive from other drives in the array . Rebuilding applies only to fault-tolerant arrays such as RAID 1, or RAID 10. T o replace the old drive, make sure to use a new drive of equal or greater capacity .
- 85 - Appendix 5-2-1 Conguring 2/4/5.1/7.1-Channel Audio The motherboard provides six aud io jacks on the back pan el w hi ch s upp or t 2/ 4/ 5.1 /7 .1 -ch an ne l (Note) au dio . The picture to the right shows the default audio jack assignments.
Appendix - 86 - Step 2: Connect an audio device to an audio jack. The The cur- rent connected device is dialog box appears. Select the device according to the type of device you connect. Then click OK . Step 3: On the Speakers s creen, click t he Spe aker Co ngura - tion tab.
- 87 - Appendix 5-2-2 Conguring S/PDIF Out The S/PDIF Out jack (Note 1) can transmit audio signals to an external decoder for decoding to get the best au- dio quality . 1. Connecting a S/PDIF Out Cable: Connect a S/PDIF optical cable to an external decoder for transmitting the S/PDIF digital audio signals.
Appendix - 88 - 5-2-3 Enabling the Dolby Home Theater Function Before D olby Hom e Theater is enabled , you get o nly 2-c hannel p layback output ( from the front speakers) when playing 2-channel stereo sources. Y ou must play 4-, 5.1-, or 7.1- chan- nel content to get 4-, 5.
- 89 - Appendix 5-2-4 Conguring Microphone Recording Step 2: Connect your microphone to the Mic in jack (pink) on th e ba c k pa ne l o r th e M ic i n j ac k ( pi nk ) o n th e f ro nt panel. Then congure the jack for microphone function - ality .
Appendix - 90 - Step 5: After co mpletin g the set tings a bove, cl ick Start , p oint to All Programs , point to Accessories , and then click Sound Recorder to begin the sound recording. Step 1: Loca te t he i con in th e not ifi cati on a rea a nd ri ght - click on this icon.
- 91 - Appendix Step 4: Now you can access the HD Audio Manager to cong - ure Stereo Mix and use Sound Recorder to record the sound. 5-2-5 Using the Sound Recorder A. Recording Sound 1. Make sure you have connected the sound input device (e.g. microphone) to the computer.
Appendix - 92 - 5-3 T roubleshooting 5-3-1 Frequently Asked Questions T o read more F AQs for your motherboard, please go to the Support & DownloadsF AQ page on GIGABYTE's website. Q: In the BIOS Setup program, why are some BIOS options missing? A: Some advanced options are hidden in the BIOS Setup program.
- 93 - Appendix 5-3-2 T roubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. ST ART A Turn off the power . Remove all peripherals, connecting cables, and power cord etc.
Appendix - 94 - The power supply , CPU or CPU socket might fail. The keyboard or keyboard connector might fail. END A Turn off the computer . Plug in the keyboard and mouse and restart the computer . The graphics card, expansion slot, or monitor might fail.
- 95 - Appendix.
Appendix - 96 -.
- 97 - Appendix.
Appendix - 98 -.
- 99 - Appendix Contact Us • GIGA-BYTE TECHNOLOGY CO., L TD. Address: No.6, Bao Chiang Road, Hsin-Tien Dist., New T aipei City 231,T aiwan TEL: +886-2-8912-4000 F AX: +886-2-8912-4003 T ech. and Non-T ech. Support (Sales/Marketing) : http://ggts.gigabyte.
Appendix - 100 - • G.B.T . TECHNOLOGY TRADING GMBH - Germany WEB address : http://www .gigabyte.de • G.B.T . TECH. CO., L TD. - U.K. WEB address : http://www .giga-byte.co.uk • Giga-Byte Technology B.V . - The Netherlands WEB address : http://www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Gigabyte GA-880GM-USB3 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Gigabyte GA-880GM-USB3 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Gigabyte GA-880GM-USB3 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Gigabyte GA-880GM-USB3 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Gigabyte GA-880GM-USB3, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Gigabyte GA-880GM-USB3.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Gigabyte GA-880GM-USB3. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Gigabyte GA-880GM-USB3 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
