Manuale d’uso / di manutenzione del prodotto 2000 del fabbricante Giantec
Vai alla pagina of 36
T racer 2000 Digit al V i deo Recorder User ’ s Manual.
Tracer 2000 DVR user manual V ersion 3.0 Page 2 of 36 Content s CHAPTER I INTRODUCTION............................................................................................................... 5 LIMITED W ARRANTY .................................
Tracer 2000 DVR user manual V ersion 3.0 Page 3 of 36 1. S tandar d CMOS Featur es ...................................................................................................... .............. 24 2. Advanced BIOS Featur es ....................
Tracer 2000 DVR user manual V ersion 3.0 Page 4 of 36 Copyright Notice Copyright 2004. All Right s Reserved This document may not , in whole or in part, be repr oduced or transmitted in any form or by.
Tracer 2000 DVR user manual V ersion 3.0 Page 5 of 36 CHAPTER I INTRODUCTION Thank you for purcha sing T racer 2000 DVR; this m anual will guide you through the setu p, installation, and use of all our DVR systems.
Tracer 2000 DVR user manual V ersion 3.0 Page 6 of 36 FEATURE The TRACER200 0 co mes with th e following hardware devices: Control p anel with IR receiver One10/100Mbp s RJ-45 Ethernet Port One RS 232 and one RS2 32/4 22/485 selectable interface One VGA Connector One speaker out T wo USB Ports T wo 3.
Tracer 2000 DVR user manual V ersion 3.0 Page 7 of 36 CHAPTER II P ACKAGE Packing List Check the accessories acco mpany with the system you p urch ase as listed below . With newer p ackage release, the accessories are comp acted into an accessory box .
Tracer 2000 DVR user manual V ersion 3.0 Page 8 of 36 CHAPTER III INST ALLA TION FRONT PANEL VIEW REAR PANEL VIEW 12 CH2 CH1 CH7 CH3 CH4 CH5 CH6 CH8 CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 1 ALARM IN 3.
Tracer 2000 DVR user manual V ersion 3.0 Page 9 of 36 1 INDICATOR Power LED: Green light shows power is o n. S tatus LED: Green light continuou s on me ans working pro per ly . Green light blinking shows st atus of recording Red light continuous on mean s no signal (This may implies HDD damaged, No Po wer , or Access Error .
Tracer 2000 DVR user manual V ersion 3.0 Page 10 of 36 2.2. Connect Camera Cable to BNC connector 2.3. Connect to LAN connector: Plug RJ-45 connector to LAN Port 2.5.1 Insert RJ-45 cable to networ k LAN s ocket on the rear . 2.5.2 Connect Serial port modem to serial c on nector ( COM1) and through Dial-in function to connect to Internet.
Tracer 2000 DVR user manual V ersion 3.0 Page 11 of 36 2.4. Connect to Printer Port (option) There are two types of Printer port. One is LPT the other is USB.
Tracer 2000 DVR user manual V ersion 3.0 Page 12 of 36 3. POWER CONNECTOR 3.1. Connect power cord (110V~240V auto switch) into the pow er socket. Press “ I ” to start up system.
Tracer 2000 DVR user manual V ersion 3.0 Page 13 of 36 CHAPTER IV Pin assignment Internal Jumpers and Connectors.
Tracer 2000 DVR user manual V ersion 3.0 Page 14 of 36 Power Switch for A TX power supply (JP1) Signals JP1 Power ON/OFF 1-3 Reset/LED/Speaker (JP1) Signals JP1 Power LED, Pin 9+, Pin10- 9-10 External speaker 14-20 HDD LED, Pin8+, Pin7- 7-8 System reset swit ch 5-6 SUSLED Pin4+, Pin2- 2-4 PS.
Tracer 2000 DVR user manual V ersion 3.0 Page 15 of 36 CPU FSB Select (JP4) Function JP4 Auto by CPU 1-3, 2-4 66 MHz 3-5, 4-6 F AN control (F AN1, 2) Function F AN1,2 Sense 3 +12V 2 PWM control 1 HDD Connector (IDE1, 2) 1 2 39 40 Pin no. Signal Pin no.
Tracer 2000 DVR user manual V ersion 3.0 Page 16 of 36 Parallel/Printer connector (PRN) Pin no. Signal Pin no. Signal 1 S trobe 10 -Acknowledge 2 Data 0 1 1 Busy 3 Data 1 12 Paper Empty 4 Data 2 13 + .
Tracer 2000 DVR user manual V ersion 3.0 Page 17 of 36 General Purpose Input / Output (J3) 1 2 15 16 Pin no. signals Pin no. signals 1 GPIO-0 2 Audio IN3 3 GPIO-1 4 AGND 5 GPIO-2 6 Audio IN2 7 GPIO-3 8 AGND 9 GPIO-4 10 Audio IN1 11 GPIO-5 12 AGND 13 GPIO-6 14 Audio IN0 15 GPIO-7 16 GND(for GPIO) Infra-Red (IR) 1 5 Pin no.
Tracer 2000 DVR user manual V ersion 3.0 Page 18 of 36 PCI bus pin assignment A1 B1 A49 B49 B52 A52 B62 A62 COMPONENT SIDE SOLDER SIDE Pin no. A B Pin no.
Tracer 2000 DVR user manual V ersion 3.0 Page 19 of 36 External Connector CRT Display Connector (VGA) 1 5 15 10 Pin no. Signal Pin no. Signal 1 RED 9 N/C 2 GREEN 10 GND 3 BLUE 1 1 N/C 4 N/C 12 N/C 5 G.
Tracer 2000 DVR user manual V ersion 3.0 Page 20 of 36 COM 1 Connector 1 6 5 9 RS-232 Connector (COM1) Pin no. Signals 1 DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 R TS 8 CTS 9 RI COM2 Connector 1 6 5 9 RS-232/RS-422/RS-485 Conn ector (COM2 ) (Please setup mode type by JP3) Pin no.
Tracer 2000 DVR user manual V ersion 3.0 Page 21 of 36 Ethernet connector (RJ-45) Drawing of Ethernet connector RJ-45 Pin no. signals 1 TX+ 2 TX- 3 RX+ 4 NC 5 NC 6 RX- 7 NC 8 NC Connectors The connectors allow this main board to connect with other part s of the system.
Tracer 2000 DVR user manual V ersion 3.0 Page 22 of 36 P/T/Z Setting The P/T/Z Setting complies with LIL IN or PELCO. Protocol has been previously attached to the COM ports. Y ou may control the cam era via arrow buttons. In this case, you don’t need to buy dedicated P/T/Z controller .
Tracer 2000 DVR user manual V ersion 3.0 Page 23 of 36 CHAPTER V CMOS SETTING Introduction This manual discusse s Award™ Setup progra m built into the ROM BIOS.
Tracer 2000 DVR user manual V ersion 3.0 Page 24 of 36 1. Standard CMOS Features Use this menu for basic system configuration. Date: T ime: IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Driver B Video Halt On Based Memory Extended Memory T otal Memory Mon.
Tracer 2000 DVR user manual V ersion 3.0 Page 25 of 36 2. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. CMOS Setup Utility – Copyright © 1984 – 1 99 .
Tracer 2000 DVR user manual V ersion 3.0 Page 26 of 36 3. Advanced Chipset Features Use this menu to c hange the values in the chip set registers and optimiz e your system's performance.
Tracer 2000 DVR user manual V ersion 3.0 Page 27 of 36 4. Integrated Peripherals Use this menu to specify your settings for inte grated peripherals CMOS Setup Utility – Copyright © 1984 – 2 00 0 .
Tracer 2000 DVR user manual V ersion 3.0 Page 28 of 36 5. Power Management Setup Use this menu to specify your settings for p ower management CMOS Setup Utility – Copyright © 1984 – 2 00 0 Award .
Tracer 2000 DVR user manual V ersion 3.0 Page 29 of 36 6. PnP / PCI Configuration This entry appears if your system supports PnP / PCI. CMOS Setup Utility – Copyright © 1984-200 0 Award S oftware P.
Tracer 2000 DVR user manual V ersion 3.0 Page 30 of 36 7. PC Health Status Use this menu to monitor the CPU and system temperatur e, CPU fan speed the v olt ag e of the onboard regulators. CMOS Setup Utility – Copyright © 1984-200 0 Award S oftware PC Health S tatus CPU W arning T emperature Current System T emp.
Tracer 2000 DVR user manual V ersion 3.0 Page 31 of 36 9. Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While A ward has designed the custom BIOS to maximize performance, the factory has the ri ght to change these defaults to me et their n eeds.
Tracer 2000 DVR user manual V ersion 3.0 Page 32 of 36 CHAPTER VI System HDD Inst allation Guide Follow the step to setup HDD draw ing box. 1. Remove the screws on the case.
Tracer 2000 DVR user manual V ersion 3.0 Page 33 of 36 2. T ake off the upper cover and remove the screw s. Remove the screw ..
Tracer 2000 DVR user manual V ersion 3.0 Page 34 of 36 3. Remove HDD T ray , and inst all HDD properly ..
Tracer 2000 DVR user manual V ersion 3.0 Page 35 of 36 4. Insert the assembled HDD tray into TR ACER2000, and connect both Power and HDD cables..
Tracer 2000 DVR user manual V ersion 3.0 Page 36 of 36 5. Assemble the upper cover and the screws..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Giantec 2000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Giantec 2000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Giantec 2000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Giantec 2000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Giantec 2000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Giantec 2000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Giantec 2000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Giantec 2000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
