Manuale d’uso / di manutenzione del prodotto SILENTMAX 1000/1200 del fabbricante Genie
Vai alla pagina of 24
For Answers and Assistance: 1.800.354.3643 or visit www .geniecompany .com SAVE THIS MANUAL FOR FUTURE REFERENCE INST ALLER: LEAVE THIS MANUAL WITH HOMEOWNER GARAGE DOOR OPENER MODELS P owerMax ® 120.
Safety Information Safety Notifications .......................................... 3 Important Safety Instructions ............................ 3 Infrared Protection Function ............................. 3 Features Safety ...........................
SafetyInformation 1 OVERVIEW OF PO TENTIAL HAZARDS READ THIS SAFETY INFORMA TION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects tha t move with the help of springs under high tension and electric motors.
Features 2 SAFETY FEA TURES Safe-T -Beam ® (STB) Non-Contact Reversing System Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything passes through the beam. LED indicator lights on the powerhead and on the STBs provide a self-diagnostic code if an operational problem exists.
Required Programming 3 NOTE: Before you begin programming, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that your Genie gara ge door opener is installed, you will want to program the opener so that the door opens and closes properly and all remote devices operate correctly .
TRA VEL LIMITS NOTE: If shuttle/bullet has NOT been enga ged to carriage, do so now . See page 17. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON. If not illuminated, check for correct wiring or the Sure-Lock switch may be activated.
Required Programming 3 The DOWN (closed) limit is programmed. Opening Garage Door (Up Limits) NOTE: Beginning with garage door c losed is recommended but not necessary . The UP (open) limit is programmed. BOTH DOOR LIMITS ARE NOW PROGRAMMED . PROGRAM SET PROGRAM – + 5 Press and release the Program Set button (both LEDs flash blue and go off).
R quired Pr ramming Required Programming 3 MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator IC: 2 33A-CS 1D 120V. 60HZ. 5A S/N:10XXXX XXXXXXX STB BWC IWC NOT USED NOT USED N.
Required Programming 3 Force and Speed Control These controls are factory programmed and automa tically set themselves when you use the Wall Console to open and c lose the garage door for the rst time. The door MUST complete a full cyc le from open to close and c lose to open before it is fully set.
Required Programming 3 REMOTES / New Intellicode 2 Openers NOTE: The following instructions are for the remote control transmitters (“Remotes”) provided with this opener . This Remote is preset for use with the Intellicode 2 Access Security System.
The Remote button is now programmed. Repeat as necessar y for additional Remotes. T o program the same Remote for other garage door openers, repeat the steps above using one of the other two Remote buttons. Each Remote can be programmed for three door openers.
Optional Programming 4 Setting Up a PIN 1. Press in order 3–5–7. 2. Press the Program key . 3. Enter your new PIN (3-8 characters). 4. Press Program key . Y our keypad is ready for programming. Programming Locate Y our Opener’ s Programming Buttons and LED Synchronizing Keypad to Opener 1.
Optional Programming 4 CLEARING MEMOR Y FOR REMOTES If the memory has been cleared, the Remote will not activate the door opener . NOTE: The garage door opener will operate normally using the Wall Console. NOTE: When the remote is pressed the round LED will flash blue but will not activate the door opener .
INTELLICODE 1 REMOTES Remotes provided with this unit can operate other (Intellicode® 1) models of Genie® garage door openers . The default Intellicode ® 2 setting must be changed to Intellicode® 1. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2.
One-Piece Doors 5 A TT ACHING DOOR BRA CKET TO DOOR NOTE: Center bracket on door as high as possible, preferably top edge . A TT ACHING DOOR ARM T O DOOR BRACKET 1 Using bracket, mark holes on door or frame and drill 5/32" hole completely through door frame.
Maintenance and Adjustments 6 If you have any questions, please do not hesitate to contact customer service a t: 1-800-35-GENIE or visit www .geniecompany .
W ARNING •Useextremecautionwhenworkingfromaladderorstepstool. • Whenreplacinglightcover , makesurewiresarenotpinchedor near moving parts.
Maintenance and Adjustments 6 CAUTION Door closing force is F ACTOR Y set and requires no adjustment for normal operation. • NEVER adjust the force settings to compensate for damage, including an unbalanced door , binding door track, or broken spring.
Maintenance and Adjustments 6 ADJUSTMENT GUIDES (continued) Speed Settings (DC motors only) Speed settings are pre-programmed at the factor y for the maximum speed.
Opener circuit wiring diagram. This wiring diagram is for reference only . WiringDiagram 7 1 2 3 4 5 6 1 2 3 7 6 POWERCORD CONNECTOR WHITE BLACK GREEN WHITE WHITE BLACK RED BLACK STRIPEDWHITE.
Troubleshooting 8 OPERA TION Need help or have questions? DO NOT RETURN to the store. Call us: 800-354-3643 PROBLEM WHA T TO DO Opener does NO T run from wall console. •Checkpowersource. – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK.
Troubleshooting 8 Powerhead LED Possible Problem Solution Round LED Long LED OFF OFF Normal operation. None required. No response from unit. Check power supply. Contact a trained door system technician. ON/RED/ STEADY ON/RED/ STEADY Limits NOT set properly.
PowerMax ® 1200/1500, SC 1200/1500, TriloG ™ 1200/1500, PowerLift ® 900, GPower ™ 900, SilentMax ® 1000/1200, CB 1000/1200, IntelliG ® 1000/1200 LIMITED WARRANTY GMI Holdings, Inc d/b/a The Ge.
Looking for Leading-Edge T echnolog y or the P erfect Update/Replacement? Genie ® Has the Answer! L ea ding- Edge Techn ol og y Closed Conrm™ W ireless Remote (Works with Rev olution Series 1500, 1200 and 1000 Models) • Sleekandcompactdesign • Beepsandashesgreenwhengarage doorcloses.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Genie SILENTMAX 1000/1200 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Genie SILENTMAX 1000/1200 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Genie SILENTMAX 1000/1200 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Genie SILENTMAX 1000/1200 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Genie SILENTMAX 1000/1200, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Genie SILENTMAX 1000/1200.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Genie SILENTMAX 1000/1200. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Genie SILENTMAX 1000/1200 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
