Manuale d’uso / di manutenzione del prodotto GPS-IC del fabbricante Genie
Vai alla pagina of 32
Au t o mat i c Cha i n D riv e/ Be lt D rive Ga ra ge Door O p er a t or S yst e m Owner ’ s Manual SA VE FOR FUTURE REFERENCE Customer Ser vice CALL: 1-800-354-3643 VISIT : WWW .
Things to consider if you are planning to “ do-it-yourself. ” Whether you are replacing an existing garage door operator or installing an operator in your garage for the first time, there are some pre-installation issues which need to be addressed.
3 TYPICAL SECTIONAL DOOR INST ALLA TION 5 TYPICAL SUPPORT BRACKET EXTENSION SPRING OR T ORSION SPRING SAFE-T -BEAM ® BRACES ADDED HEADER BRACKET MOUNTING BOARD 36 ” POWER CORD TO 120V GROUNDED OUTL.
4 W ARNING : Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual.
NOTE: Accessories vary by model . F ASTENERS - Shown full size. See Parts List for description. 10 5 10 4 103 101 10 6 12 6 12 4 12 5 Lag Screw , 1/4 ” x 2 ” Cotter Pin Clevis Pin Bolt, 3/8 ” -16 x 7/8 ” Phillips Hex Head Screw , No.
Stealth Power Head 2 3 4 5 6 7 8 9 10 1 12 13 14 15 16 17 18 19 20 11 22 23 24 25 26 27 28 29 30 21 32 33 34 35 36 37 38 39 31 40 12 12 12 12 11 19 3 12 26 26 Item Part Name 1 Lens 2F ront Cover 3S id.
7 PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 61 Main Drive Worm 62 Screw , #8 x 3-1/8 ” Slot HH, Sf T ap 63 Limit Switch Plate 64 Screw , #6 x 3/8 ” Phill.
Channel Item Part Name 66 Belt & Bullet Assembly - 7 ’ 6 ” Door (Belt Models Only) Belt & Bullet Assembly - 8 ’ Door (Belt Models Only) Belt & Bullet Assembly - 10 ’ Door (Belt Mod.
9 Rail PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 102 Boom Support Kit (not shown) 103 Safety & Maintenance Guide 104 Emergency Release T ag (Tri-L) 105 Entrapment W ARNING Label 106 Wire 11 0 R a il (L=1 12.
Fig. 1-3 No. 10-24 x 1/2 ” Hex Head Screws 5/16 ” x 1/2 ” Hex Head Screws “ D ” -Shaft and Hole 3. Place power head and channel on clean, flat surface. 4. Slide drive end of channel down over “ D ” -shaft on top of power head (Fig. 1-2).
Fig. 1-4 Adjusting Bolt WHA T TYPE OF DOOR DO YOU HA VE? Look at the drawings below . They tell you where to find the installation instructions you need T rack Guided Doors SEE SECTION 2A T rackless Doors SEE SECTION 2 B.
W ARNING • Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Repairs and adjustments must be made by a trained service person using proper tools and instructions.
CAUTION CAUTION Fig. 2-5 Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. Power Head Channel/Rail Assembly 6. Mount power head (See Section 2 MOUNTING METHODS). • Be sure channel/rail assembly and power head are on door center line (Line “ V ” ).
8. Install door bracket (Fig. 2-6). • Contact door manufacturer . NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed.
CAUTION W ARNING Header bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 1. Establish center line of door and header (Fig. 2-9). • Close door . • Measure door width. Mark center .
CAUTION 6. Install door bracket (Fig. 2-12). • Contact door manufacturer for proper installation. NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed.
CAUTION Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 9. Mount power head (See Section 2 AL TERNA TE MOUNTING METHODS). • Be sure rail assembly and power head are on door center line (line “ V ” ).
NOTE: Mounting brackets can be attached to the floor using concrete anchors (not provided). 2. Mounting STB source and sensor . • If garage has only one garage door . – Determine which side of garage receives most direct sunlight (Fig. 3-4) . – Red LED should always be on sunny side whenever possible (Fig.
CAUTION FIG. 3-8 (ProMax) Attachments at power head . • Make wire attachments at STB ’ s. – Splitting and stripping wire ends to be connected as shown (Fig. 3-6) . – Loosen terminal screws. – Insert wire under flat plate and tighten screw . It does not matter which wire, white or striped, goes on which terminal (Fig.
CAUTION W ARNING W all console W all button OR Fig. 4-2 #6 x 1 ” pan head screws Fig. 4-3 MORE T MENT OPEN PUSH LIMITS TO SET G4 Y3 B2 W1 1. Run wire from power head to wall control. • Place the wall control: – In sight of door . – At least 5 feet from floor , so small children can not reach it.
1. Disconnect the power cord from the branch circuit mains. 2. Remove bottom cover from power head. • Remove four (4) hex head screws from front and rear covers. • Slide bottom cover off. 3. Remove existing power cord from power head. • Disconnect three power cord wires.
W ARNING Fig. 6-1 MORE MORE LIMIT ADJUSTMENT CLOSE OPEN PUSH LIMITS TO SET 4 3 2 1 CLASS 2 NEC OPEN CLOSE TO SET LIMITS PUSH OR NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPE.
NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPEN FORCE CLOSE FORCE RADIO SIGNAL LEARN CODE COM DO NOT PUSH LIMIT SET UNLESS DOOR IS ATTACHED NOTE: USE ONLY WITH SERIES II CONTROLS CLOSE MORE OPEN MORE CLOSE OPEN LIMIT ADJUSTMENT U.
W ARNING During the following steps, the motor protector may open. W ait about 20 minutes for protector to reset. 1. Adjusting the “ OPEN ” limit switch (Fig. 8-1). • Run door to open position by pushing wall control. • Locate curved “ OPEN ” limit adjustment slot on back of power head.
1. T urn remote control upside down (Fig. 10-1) 2. Battery replacement (your remote control is battery powered). • Gently push straight IN on tab as shown (Fig. 10-1). – use ball point pen, coin or small screwdriver . – battery cover snaps open.
1. Install light bulb(s) into socket(s). Do Not use short neck bulb(s). • Use bulb(s) rated for: – rough service. – vibration. – appliances. • 1 00 watt maximum. 2. Bend two (2) slotted tabs up. This will activate the ” living hinge ” of the lens (Fig.
MONTHL Y MAINTENANCE DOOR SPRINGS and DOOR HARDW ARE • Do not operate garage door automatically or manually if springs are broken. CONT ACT A PROFESSIONAL FOR SERVICE. • Oil door rollers, bearings, and hinges monthly . Use silicone lubricant or light oil.
CAUTION Door starts for no reason. Check staples on wire from power head to wall control. If they cut into insulation, they can short wires. If wire is cut, replace it. W as a remote control lost or stolen? Erase all remote control codes from receiver memory and reprogram.
CAUTION ( Stealth Motor ) Openin g cover could cause electrical shock. WIRING DIAGRAM FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM 29 ( ProMax Motor ).
30 No C.O .D . shipments. Please include check or money order , made pay able to The Genie Company . Do not send cash .A llow 3-4 weeks f or delivery . 1-800-354-3643. Please have part number and credit card ready . Mail Order Form to: Genie Company , Alliance, Ohio 44601 .
INST ALLA TION NOTES FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM CONT ACT NUMBERS NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP A.
SA VE THESE INSTRUCTIONS Manufactured under one or more of the following U.S. patents: 3,898,582 / 4,041,259 / 4,048,630 / 4,064,487 / 4,103,238 / 5,222,403 Other Patents applied for 22790 Lake Park Blvd. • Alliance, Ohio USA • 44601 Customer Service 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Genie GPS-IC è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Genie GPS-IC - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Genie GPS-IC imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Genie GPS-IC ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Genie GPS-IC, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Genie GPS-IC.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Genie GPS-IC. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Genie GPS-IC insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
