Manuale d’uso / di manutenzione del prodotto GEM-P800 del fabbricante Gemini
Vai alla pagina of 16
Usin g Y our GEM-P800 Security Sy stem ARMED STATUS GEMINI 1 2 3 4 5 6 7 8 Oi219c page 1 Tuesday, September 16, 1997 08:24.
Introduction Congratulations on y our purc hase of an advanc ed GEMINI-P800 Secur ity System. Meticulously developed by a leading manuf actur er of s tate-of- the-art sec urity products, this system will provide you w ith unprecedented peace- of-m ind & inc orpo- rates som e of the m ost sophis ticated f eatures available today.
3 Important - T est Your Sy stem Weekly ! 1 Bell / Battery Test Test y our bell or s iren by pressing followed by . This will cause the bell, or siren to s ound for 2 seconds and also initiate a test of the battery . 2 Zone Test W alk throughout the prem ises , opening each protected door or window, and activating each m otion sensor .
ARMED STAT US GEMINI 1 2 3 4 5 6 7 8 4 Key pad Controls and Indi cator s Status Light will light when all zones are secure and system is ready to be Armed. A C Light will light to indicate that AC Power is present. Trouble Light will light and the Keypad sounder will pulse to indicate that a system tr ou- ble is present.
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g Zone num ber will be lit. Secure these zones bef ore proceedin g .
Protecting Yourself While at Home 1 Bef ore arm in g y our system, m ak e s ure the g reen Statu s li g ht is ON. T his indic ates that all of your protective zones are secure. If any z ones are open, the cor respondin g zone number will be lit. Secure thos e zones before proc eedin g .
Emergency Buttons The three s ets of em er gency buttons, if progr am m ed, are always active whether the system is ar m ed or disarm ed. Discus s these Buttons with y our installer. The em ergency signal will only be activated when the two respective buttons are pres sed at the sam e tim e.
Disarming Your Sy stem when Returning 1 Enter your premises throu g h the Entry/Exit door. The k eypad w ill sound a steady tone to remind you to disarm the system before your Entry Delay tim e ex pires. 2 Enter your User Code and press . The red Ar m e d li g ht will g o out, indicatin g that the system has been dis arm ed.
Preparing a Fire Escape Plan Even with the most advanc ed fire alar m s ystem, adequate protection r equires an es cape plan. To prepar e your plan, draw floor plans of your building. (space is pr ovided on the next page) Show two exits - a f ront or back door and a window from each room .
10 Fire Protection Floorplan Draw a plan of your premis es below. Oi219c page 10 Tuesday, September 16, 1997 08:24.
Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy A rm (when system is dis arm ed) The Easy Arm feature allows the s y stem to be arm ed by pressing f ollowed by .
12 The G EM-P800 is constantly monitor ing its own com ponents, as well as all c ritical services , such as AC pow er and the telephone line, to insure that it is alway s ready to provide the protection for which it was des igned. W hen a system trouble does occur , it will caution you by lighting the TROUBLE light and beeping the keypad buzz er.
13 Sy stem Troubles Keypad Beeps or Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for serv ice. 2 Beeps 3 W ireless Receiver Trouble A problem has been detected w ith the wireless receiv er.
Your Installer has assigned a User 1 Code which can be used to not only Arm and Dis arm the system, but also to enter the User Program Mode, where y ou can program other user c odes. The following explains how you will use this code to progr am or erase additional user codes .
A mbush Code - In the event that y ou are forc ed by an intruder to disarm your system, this special code c an be used to disarm the system , and simultaneously send a silent alarm to Central Station. If y our s ystem has the Am bu sh f eatu re enabled, the code assigned as the User 8 code will function as y o ur Ambush Code.
NA PCO LIM I TED WA RRA NTY THE FOLL OW ING STATEM ENT IS REQUI RED BY THE F C C . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Gemini GEM-P800 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Gemini GEM-P800 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Gemini GEM-P800 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Gemini GEM-P800 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Gemini GEM-P800, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Gemini GEM-P800.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Gemini GEM-P800. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Gemini GEM-P800 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
