Manuale d’uso / di manutenzione del prodotto ZET3058 del fabbricante GE
Vai alla pagina of 16
1 31-10663 1-07 JR Installation 30” Built-In T rivection ™ Instructions W all Oven JT930, JT980, ZET3038, ZET3058 BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Save these instructions for local inspector’ s use.
2 Installation Instructions PREP ARE TO INST ALL THE OVEN TOOLS YOU WILL NEED MA TERIALS YOU MA Y NEED Wire Nuts Junction Box 60” of String for Single Ovens 96” of String for Double Ovens Adjustab.
3 Installation Instructions PRE-INST ALLA TION All installation information on the following pages is to be used for SINGLE and DOUBLE oven installation! Remove packaging materials. Check behind hinges. Remove plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.
4 Installation Instructions SINGLE BUIL T -IN OVEN CUTOUT OPTIONS W ALL MOUNT—SINGLE BUIL T -IN OVEN OPTION Cabinet Width 30” Recommended Cutout Location from Floor 32 1/2” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 27 1/4” Min.
Installation Instructions W ALL MOUNT—SINGLE BUIL T -IN OVEN BELOW AN ADV ANTIUM OVEN OPTION • When installed over a single wall oven, allow at least 2” between the two openings. This separation will provide clearance for bottom overlap of the Advantium oven and top overlap of the single wall oven.
6 UNDER COUNTER—SINGLE BUIL T -IN OVEN OPTION D T op and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely , since they will anchor the oven in the cabinet. 25” 24” 27 1/4” Min.
Installation Instructions 7 DOUBLE BUIL T -IN OVEN CUTOUT CUTOUT FOR DOUBLE BUIL T -IN OVEN Cabinet Width 30” Recommended Cutout Location from Floor 12” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 51 13/16” Min.
ON DOUBLE W ALL OVEN MODELS, REMOVE THE LOWER DOOR ONL Y (CONT .): Close door to the door removal position, which is halfway between the broil stop position and fully closed.
Installation Instructions 9 9 ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate.
10 Installation Instructions ELECTRICAL CONNECTIONS (CONT .) CONNECT CONDUIT With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below . Position the conduit in such a manner that it will lie behind the oven in a natural loop when the oven is installed.
11 Installation Instructions THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a three-conductor branch circuit, if local codes permit: Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
12 Installation Instructions SECURE THE OVEN IN THE OPENING SLIDE THE OVEN INTO THE OPENING Loop (do not tie) the correct length of string around the conduit before the oven is slid into place. This will keep the conduit from falling improperly behind the oven.
13 Installation Instructions T o install a single metal bottom trim assembly (on some models), see Step 11. T o install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12. INST ALL THE MET AL BOTTOM TRIM With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening.
14 Installation Instructions REPLACE THE LOWER OVEN DOOR ON DOUBLE W ALL OVEN MODELS ON DOUBLE W ALL OVEN MODELS, REPLACE THE LOWER DOOR: Firmly grasp both sides of the door at the top. With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot.
15 Installation Instructions FINAL CHECKLISTS PRE-TEST CHECKLIST Remove all protective film. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see Steps 11 and 12).
16 Printed in the United States.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il GE ZET3058 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del GE ZET3058 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso GE ZET3058 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul GE ZET3058 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il GE ZET3058, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del GE ZET3058.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il GE ZET3058. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo GE ZET3058 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
