Manuale d’uso / di manutenzione del prodotto ZBD6890K del fabbricante GE Monogram
Vai alla pagina of 16
If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Monogram. ® Installation Instructions Built-In Dishwashers ZBD6800K ZBD6880K ZBD6890K* Design Guide with Installation Instructions * For ZBD6890 Series also refer to the instructions provided on the template packed with that model.
Safety Information 2 CONTENTS Installation Preparation Parts Supplied ..............................................................................3 Materials Y ou Will Need ............................................................3 T ools Y ou Will Need .
TOOLS YOU WILL NEED: Phillips head screwdriver 5/16" and 1/4" nutdriver 6" Adjustable wrench Level Carpenters square Measuring tape Safety glasses Flashl.
PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop.
DRAIN REQUIREMENTS • Follow local codes and ordinances. • Do not exceed 10 feet distance to drain. • Do not connect drain lines from other devices to the dishwasher drain hose. NOTE: This dishwasher is equipped with a high drain loop. There is no minimum height required for drain hose routing.
6 Installation Preparation PREP ARE ELECTRICAL WIRING W ARNING FOR PERSONAL SAFETY : Remove house fuse or open circuit breaker before beginning installation.
PREP ARE HOT W A TER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure F . • The line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" dia. hole to accommodate the water line.
REMOVE WOOD BASE, INST ALL LEVELING LEGS IMPOR T ANT — Do not kick off wood base! Damage will occur . • Move the dishwasher close to the installation location and lay it on its back. • Remove the four leveling legs on the underside of the wood base with an adjustable wrench or 15/16" socket.
Drain Outlet Hose Clamp Shoulder Stop INST ALL TRIM PIECES Skip this step if trim is not supplied with the dishwasher . • Locate trim strips inside dishwasher . • Press trim onto the tub flange on each side. Start with the top edge, pressing on as you move towards the bottom.
POSITION DISHW ASHER UNDER COUNTERTOP STEP 10 10 • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur . • Check that the tub insulation blanket does not get “ bunched-up ” or interfere with the springs as you slide it into the cabinet.
LEVEL DISHW ASHER IMPOR T ANT — Dishwasher must be level for proper dish rack operation and wash performance. • Place level on door and rack track inside the tub as shown to check that the dishwasher is level. • Level the dishwasher by adjusting the four leveling legs individually .
CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit 5/8" or 1" diameter connections on the air gap, waste tee or disposer . Cut on the marked line as required for your installation. • If a longer drain hose is required, add up to 42" of length for a total of 10 ft.
13 Installation Instructions PRE-TEST CHECK LIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty . Check to be sure power is OFF . Open door and remove all foam and paper packaging.
REPLACE TOEKICK • Place toekick against the legs of the dishwasher . • Align the toekick with the bottom edge and make sure it is against the floor . • Insert and tighten the two toekick attachment screws. The toekick should stay in contact with the floor .
Custom Panel Dimensions 15 CUSTOM P ANEL FOR MODEL ZBD6890 This dishwasher requires a field installed 3/4" thick custom panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-30569.
Pub. No. 31-30568 Part No. 206C1559P108 12-03 JR NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il GE Monogram ZBD6890K è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del GE Monogram ZBD6890K - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso GE Monogram ZBD6890K imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul GE Monogram ZBD6890K ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il GE Monogram ZBD6890K, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del GE Monogram ZBD6890K.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il GE Monogram ZBD6890K. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo GE Monogram ZBD6890K insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
