Manuale d’uso / di manutenzione del prodotto DBI.333 del fabbricante GE
Vai alla pagina of 24
GEAppliances.com DBL333 DCL333 DVL223 Dr y ers 134098700 175D1807P367 49-90105 08-01 JR Safety Instr uctions . . . . . . . . . 2–5 Operating Instr uctions Control Panels . . . . . . . . . . . . . . . .6 Control Settings . . . . . . . . . . . . . . .
IMPORT ANT SAFETY INFORMA TION. READ ALL INSTRUCTIONS BEFORE USING. 2 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions W ARNING! For your sa.
■ Properly ground dryer to conform with all governing codes and ordinances. Follow details in the Installation Instructions section. ■ Install or store where it will not be exposed to temperatures below freezing or exposed to the weather . ■ Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.
4 WHEN USING YOUR DRYER ■ Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped. ■ Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room.
WHEN NOT USING YOUR DRYER ■ Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling. Place the cord away from traffic areas so it will not be stepped on, tripped over or subjected to damage.
6 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions About the control panel. Y ou can locate your model number on the label on the front of the left side of the door opening.
IMPORT ANT : Clean the lint filter each time you use the dryer . T emperature REGULAR For regular to heavy cottons. MEDIUM For synthetics, blends, delicates and items labeled permanent press. FLUFF For fluffing items without heat. Use the TIMED DRY cycle.
8 The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer . The fabric may then be washed and dried normally .
9 Machine wash cycle Normal Permanent Press/ wrinkle resistant Gentle/ delicate Hand wash Do not wash Do not wring Water temperature Hot (50 ° C/120 ° F) Warm (40 ° C/105 ° F) Cold/cool (30 ° C/8.
Using the four shipping carton corner posts as padding (two on each side), carefully lay the dryer on its left side and remove foam shipping pad. CAUTION: T o prevent damage, do not use the control panel as a means to pick up or move the dryer . Return the dryer to an upright position.
11 Electrical Connection Information for Gas Dryers WARNING— T o reduce the risk of fire, electric shock, or personal injury: • DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE. • DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
If all rigid metal duct cannot be used, then flexible all-metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a co.
Replace brass connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used. WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury . Always use NEW flexible connectors when installing a gas appliance.
14 Do Not Install the Dryer: Do not install the dryer in an area exposed to dripping water or outside weather conditions. Do not install the dryer in an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air .
15 Rough-In Dimensions Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 ″ (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred.
16 DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.
Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner . Install a UL-approved strain relief into the power cord entry hole of the mounting bracket. Use a strain relief which attaches to the mounting bracket with a nut.
18 Remove the shipping cap from gas pipe at the rear of the dryer . NOTE: DO NOT connect the dryer to LP gas ser vice without converting the gas valve. An LP conversion kit (Pub. No. 14-A038) MUST be installed by a qualified gas technician. Connect a 1/2 ″ (1.
19 Reversing the Dryer Door Swing Open the dryer door . Remove the 4 hinge hole plugs or screws from the left side of door opening. Place nearby for future installation. NOTE: Y ou may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint.
Problem Possible Causes What T o Do Dryer doesn’t start Dr yer is unplugged • Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker • Check the household Distribution Panel fuse/circuit is tripped breaker box in your home, and replace fuse or reset breaker .
21 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions GEAppliances.com Problem Possible Causes What T o Do Inconsistent T ype of heat • Auto.
22 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Notes..
23 For The Period Of: GE Will Replace: One Y ear Any part of the dryer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty , GE will also provide, free of charge, all labor and in-home ser vice to original purchase replace the defective part.
Printed in the United States Consumer Support. GE Appliances W ebsite GEAppliances.com Have a question or need assistance with your appliance? T r y the GE Appliances W ebsite 24 hours a day , any day.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il GE DBI.333 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del GE DBI.333 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso GE DBI.333 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul GE DBI.333 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il GE DBI.333, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del GE DBI.333.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il GE DBI.333. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo GE DBI.333 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.