Manuale d’uso / di manutenzione del prodotto DFF3 del fabbricante Furuno
Vai alla pagina of 32
NETW ORK SOUNDER DFF3 OPERA T OR'S MANU AL www .furuno .co .jp MODEL.
i IMPORTANT NOTICES • The descri ptions in thi s manual are intended for r eaders with a solid knowledge of English. • No part of this manual may be copied or reproduced without writ t en permission. • If this manual is lost or worn , contact your dealer about r epla cement.
ii SAFETY INSTRUCTIONS Do not operate the equipment with wet hands. Electrical shock can result. Do not place liquid-filled containers on the top of the equipment. Electrical shock can result. Do not install the equipment where it may be subjected to rain or water splash.
SAFETY INSTRUCTIONS iii Standard compass Steering compass 0.95 m 0.60 m CAUTION CAUTION The transducer cable must be handled carefully, following the guidelines below. • Keep fuels and oils away from the cable. • Locate the cable away from chemicals.
iv TABLE OF CONTENTS FOREWORD .............. .............. ................... .............. .................. .............. ................... .... v SYSTEM CONFIGURATION ............ .............. ................... .............. ...........
v FOREWORD A Word to the Owner o f the DFF3 Congratulations on your ch oice of the FURU NO DFF3 Network Sounde r. We are conf ident you will see why the FURUNO name has become synonymous with quality and reli abi lity. For 60 year s FURUNO Electric Com pany has en joyed an enviabl e reputation for qualit y marine electroni cs equipment .
vi SYSTEM CONFIGURATION Basic configurati on shown with solid line. 100/1 10/1 15/ 220/230 V AC 1 φ , 50/60 Hz Network Sounder DFF3 12-24 VDC Low Freq.
1 1. MOUNTING 1.1 Equip ment Li sts Standard su pp ly Opti o nal su pp ly Name Type Code No . Qty Remarks Networ k Sounder DFF3 — 1 Spare Parts SP02-0 5601 001-033 -740 1 set Fuse Instal lation Mat erials CP02-085 00 000-011 -917 1 set - Power cable (3.
1. MOUNTIN G 2 Transdu cer , thru-hu l l pipe and tank com binations Output (W) Freq uenc y (kHz) Ship type Tran sduc er Thru- hull pipe Tank 1k/1 k 28/50 St eel 28F-8 50B-9B TWB -6000(2) T-6 56 FRP -.
1. MOUNTING 3 2k/2 k 28/50 Ste el 28F-18 50B-12 TFB -7000(2) T-63 4 FRP T RB-1100(2 ) T-634-F 28/82 Ste el 28F-18 82B-35 R TFB-7000( 2) T-636 FRP T RB-1100(2 ) T-636-F 28/88 Ste el 28F-18 88B-10 TFB -.
1. MOUNTIN G 4 2k/3 k 28/150 S teel 28F-18 150B-1 2H TFB-70 00(2) T-637 FRP TRB -1100( 2) T -637 -F 50/107 S teel 50B-12 100B-1 0R TFB-70 00(2) T-643 FRP TRB -1100( 2) T -643 -F 50/150 S teel 50B-12 1.
1. MOUNTING 5 3k/3 k (con’t) 28/88 Steel 28BL-12H R 88F-126 H TFB-7000( 2) T-682 FRP T RB-1100(2 ) T-682-F Steel 28F -24H 88F-126 H TFB-7000( 2) T-682 FRP T RB-1100(2 ) T-682-F 28/150 S teel 28BL-12.
1. MOUNTIN G 6 3k/3 k (con’t ) 50/200 St eel 50BL-2 4H 200B-1 2H TFB-70 00(2) T-695 FRP TRB -1100( 2) T -695 -F Steel 50BL- 24HR 200B-1 2H TFB-70 00(2) T-683 FRP TRB -1100( 2) T -683 -F Steel 50F -2.
1. MOUNTING 7 2k (c on’t) 50 Steel 50B-12 TFB- 5000(1) T-61 1 FRP T RB-1000(1 ) T-611-F Steel 50BL-1 2 TFB-500 0(1) T-702 FRP T RB-1000(1 ) T-702-F Steel 50BL-1 2HR TFB-5000(1) T- 702 FRP T RB-1000(.
1. MOUNTIN G 8 1.2 Netwo rk Sound er The network sounder can be install ed on a desktop, deck or on a bulkhead. When selec ting a mounting locati on for the network sounder, kee p the fol lo wing in mind: • The temperature and humidit y at the mounting site should be mod e rat e and stable.
1. MOUNTING 9 • A magneti c compass will be affected if the network sounder is placed too c lose to it . Observe the compass saf e distances noted i n t he safety inst ruc tions to prevent di sturbance to the mag- netic c ompass.
1. MOUNTIN G 10 1.5 Optio na l Te mp era t ure Sen so rs 1.5.1 Tr ansom mount temperature sensor T-02MTB • Fix the cable at a convenient loca tion with cable clamp. • When the cable is led in through the tran som board, make a hole of approx . 17 mm in diameter to pass the conne ctor .
1. MOUNTING 11 1.5.2 Thru-hull temperature sensor T-02MSB, T-03MSB Select a s uitable mounting l ocation consi dering the f ollowing poin ts: • Select a mi d-boat flat po sition.
12 2. WIRING 2.1 Wiring O utline Connect the power cable, transducer cables, sensor cable, network cabl e and ground wire to their respective locations on the n etwork sounder.
2. WIRING 13 2.2 Trans ducer Cable TD-ID transd uc er (Air mar make transd uc er) The TD-ID type tr ansducer can be connected to t h i s equipment. However, note th e following lim- itations : • TD-ID transducer cannot be used with NavNet , NavNet vx2.
2. WIRING 14 4. Connect the transducer cable to t he WAGO connector, followi ng the inst ructions in the figure below and the inter connec tion dia gram. ( The opener fo r the WAGO connector i s attached in- side the equipment . See the fi gure above.
15 3. INITIAL SETTINGS 3.1 Tap Se tting This equipment is preprogr ammed for use with certai n transducers. A jumper wire i nside the equipment is set acco rding to transdu cer model. Check the jumper wire setting i nstructions on the sticker att ached to the chassis.
3. INITIAL SE TTINGS 16 3.2 DIP Switch Setting The DIP switch S2 sets up th e system accordi ng to the equipment connected. I n the default setting all switche s (1-8) are OFF. The DIP swit ch S3 should not be adjusted; leave al l swi tches in the OFF positi on.
3. IN ITIA L SETT INGS 17 DIP SW S2 sett ing, so under a nd IP a ddress Transduce r setting at NavNet/Na vNet3D After setting up the tr ansducer at the DFF3, set transduc er type at NavNet, NavNet 3D. See re- spective I nstallation Manual for the proc edure.
3. INITIAL SE TTINGS 18 3.3 Ope ra tio n Check For NavNet, the DFF3 is powered on/of f from ship ’s switc hboard. For NavNet 3D, it i s powered on/off f rom the displ ay unit. The LED on the c over of t he DFF3 lig hts or bl inks accor ding t o e quip- ment state, as descri bed i n the table below.
19 4. MAINTENANCE 4.1 Ma inten ance Regular maintenanc e is essential f or good performance. Check the items li sted in the table below at th e suggested interval to help k eep your equipment in good sh ape for years to come. Item Check po int, acti on Check i nterval Transd ucer cables Check th at cables are t ightly fast ened and are not damaged.
4. MAINTENANC E 20 4.2 Rep lacin g the Fuse The 5A fuse ( Type: FGBO-A 125V 5A PBF, Code No. 000-155-85 3-10) in the snap-in fuse hol der on the power cabl e protects th e equipment from equipment f ault and rever se polarity of t he ship's mains.
ＰＡＣＫＩＮＧ ＬＩＳＴ 02GF-X-9851 -0 DFF3-J/E N A M E O U T L I N E DESCRIPTION/CODE № Q'TY 1/1 ユニット U NIT ﾈｯﾄﾜｰｸ魚探 NETWORK SOUNDER DFF3 000-0 11-9 16-00 .
FURUNO DFF3 SP - 1 E2 037S01A 080318 SPECIFICA TIONS OF NETWORK SOUNDER DFF3 1 GENE RAL 1.1 T X frequency 28-200 kHz, two frequencies alternatel y transmitted (selectable) 1.2 Output powe r 1/2/3 kW nominal 1.3 Amplifier t ype Wide dynamic range linear amplifier (double superheterodyne) 1.
Jan.18'08 R.Esumi D-1.
2 4 3 A 1 B C DRAWN CHECKED APPROVED DWG.No. TITLE NAME 名称 INTERCONNE CTION DIAG RAM 相互結線図 REF.No. SCALE MASS kg C2037-C01- A T.YAMASAKI DFF3 ネットワーク魚探 NETWORK SOUN DER 02-161-1001-0 T.TAKENO NOTE *1: SHIPYARD SUPPLY. *2: OPTION.
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : MAR 2008 . Printed in Japan All rights reserved.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Furuno DFF3 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Furuno DFF3 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Furuno DFF3 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Furuno DFF3 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Furuno DFF3, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Furuno DFF3.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Furuno DFF3. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Furuno DFF3 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
