Manuale d’uso / di manutenzione del prodotto 8196428 del fabbricante Frymaster
Vai alla pagina of 40
Frymaster, a member of the Co mmercial Food Equipm ent Service Ass ociation, recomm ends usin g CFESA Certified Technicians. 24-Hour Service Hotline 1-800-551-8633 AUGUST 200 8 www.
i NOTICE IF, DURING THE WARRANTY PERIOD, TH E CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED D IRECTLY FROM FRYMASTER DEAN , OR ANY O F ITS AUTHORIZED SERVICE CEN TERS, AND/OR THE PART BEING U SED IS MODIFIED FR OM ITS ORIGINAL C ONFIGURATI ON, THIS WAR RANTY WIL L BE VOID.
ii DANGER Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical conduit. A restraint kit is provided with the fryer. If the restraint kit is missing contact your local Frymaster Factory Authorized Service Center (FASC) for part number 826-0900.
iii YFPRE SERIES ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS ........................................................................................................ i CHAPTER 1: Service Procedures 1.1 General .............................
1-1 YFPRE SERIES ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frym aster fryer, disconnect the fr yer from the electrical power supply. When electrical wires are disconnect ed, it is recommended that they be marked to facilitate re- assembly.
1-2 3. Remove the two screws from the upper corners of the contr ol panel and allow the control panel to swing down. 4. Unplug the wiring harness from the 15-pin connector on the interface b oard and disconnect the grounding wire from terminal adjacent to the 15- pin connector on th e back of the controller.
1-3 3. Remove the four screws from both the left and right sides of the lower back panel. 4. Locate the high-limit that is being replaced and follow the two-black wires to the 12-pin connector C-6. Note where the leads are connected prior to removing them from the connector.
1-4 5. Raise the element and remove the securing pro be bracket and m etal tie wraps that secure the probe to the element (see illustr ation below). 6. Gently pull on the temperature probe and grommet, pulling the wires up the rear of the fryer and through the element tube assembly.
1-5 1.6 Replacing a Heating Element 1. Perform Steps 1-3 of section 1.5, Replacing a Temperature Probe . 2. On full-vat fryers where the temperature probe is attached to the elem ent being replaced, disconnect the wire harness c ontaining the probe wiring.
1-6 8. Reconnect the element connector ensuring that th e latches lock. 9. Insert the temperature probe lead s into the 12-pin wiring harness connector C-6 (see illustration below). For full-vat, the red lead goes in to position 3 and the white into position 4.
1-7 5. Unplug the elements wires (white wire s with plugs) inside component box. 6. Remove the lid. 7. Remove the screw (white arrows below) from each of the tabs on either side of the contactor box. 8. Unplug the 12-pin control cord inside the box. 9.
1-8 2. Disconnect the fryer from the electrical power s upply and reposition it to gain access to both the front and rear. 3. Slide the metal bezel up to release the bottom ta bs, then slide the beze l down to disengage the upper tabs.
1-9 21. Position the elem ent tube assembly in the f ry pot and reinstall the m achine screws and nuts removed in Step 14. 22. Reconnect the oil return flexline(s) to the fr ypot, and replace alum inum tape, if necessary, to secure heater strips to the flexline(s).
1-10 If the pump starts af ter resetting the therm al overloa d switch, then som ething is causing the motor to overheat. A major cause of overheating is when se veral frypots are filtered sequentially, overheating the pump and motor. Allow the pump m otor to cool at least 30 minutes before resuming operation.
1-11 2. Disconnect the fryer from the electrical power s upply and reposition it to gain access to both the front and rear. 3. Disconnect the flexlines running to th e oil-return manifold at the re ar of the fryer as well as the pump suction flexlines at the end of the f ilter pan connection (see photos b elow).
1-12 10. Reconnect the unit to the electrical power suppl y, and verify that the pump is functioning correctly (i.e., when a filter handle is placed in the ON position, the motor should start and there should be strong suction at the intake f itting and outflow at the rear flush port.
1-13 1.10 Interface Boar d Diagnostic Chart The following diagram and charts provide ten quick system checks that can be perform ed using only a multim eter.
1-14 1.11 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. F OHMS C F OHMS C F OHMS C F OHMS C F OHMS C 60 1059 16 130 1204 54 200 1350.
1-15 1.12 Component Wiring 1.12.1 Standard Wiring YFPRE.
1-16 1.12.2 Tilt Switch Wiring 1.12.3 Terminal Block Wiring.
1-17 1.12.4 Contactor – DELTA Co nfiguration, 3 Phase MERCURY CONTR OLS CIRCUIT.
1-18 1.12.5 Contactor – Single Phase.
2-1 YFPRE SERIES ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 1 2 3 4 ITEM PART # COMPONENT 1 803-0366 Basket, 4-Lane Cooking 2 106-9620 Cover, Full-Vat Frypot 3 803-0278 Brush, Frypot, Teflo.
2-2 2.2 Cabinetry.
2-3 2.2 Cabinetry (cont.) ITEM PART # COMPONENT 106-9311 Cabinet Assembly 1 106-9431 Upright Assembly, LT Enclosure 2 106-9432 Upright Assembly, RT Enclosure 3 824-1920 Bridge Weldment, Pump/Motor 4 2.
2-4 2.3 Drain Components ITEM PART # COMPONENT 106-9351 Drain Valve Assembly 1 106-6020 Bracket, Assembly, 1-1/ 4" Drain Valve Microswitch 2 200-1257 Retainer, Drain Valve Nut 3 220-0143 Guard, M.
2-5 2.4 Electronics and Wiring Components 2.4.1 Heating Elements and Associated Parts ITEM PART # COMPONENT 1 826-2557 Element Kit, 208V (includes Items 2-12) 826-2558 Element Kit, 240V (includes Items 2-12) 807-4653 Element, 230V 8.
2-6 2.4.2 Tilt Switch Assembly ITEM PART # COMPONENT 1 ** 106-5876SP Sensory Assembly, Magnetic Positioning 2 ** 810-3007 Magnet, Magnetic Positioning (used with Item 1) * 826-2600 Tilt Switch Kit, Me.
2-7 2.4.3 4-Lane Controller ITEM PART # COMPONENT 1 106-9353 Wingstreet 4-lane Computer * 108-1253 Wingstreet 4-lane Comput er (for Canadian units) 2 810-3141 Sound Device 3 220-4284 Guard 4 807-4199 .
2-8 2.4.4 Contactor Box I T E M PART # COMPONENT 1 106-6031 Harness Assembly, Contactor Box Control, 12 Pin 2 106-6799 Harness Assembly, 208/240V Contactor Box Power 3 220-4489 Plate, Contactor Box Co.
2-9 2.4.5 Component Box ITEM PART # COMPONENT 1 826-2260 PCB Assembly, Interface Board, SMT 2 807-0979 Transformer, 208/240/ 12VAC, 50/60 Hz, 43 VA 3 807-0680 Filter Transformer, 208/240/24V, 50/60 Hz, 20 VA 4 810-1164 Block, 1 PLC Screwless Terminal 5 807-0670 Filter Relay, Midtex DPDT 24V 6 807-4036 Switch, Power 7 810-2446 Plug, .
2-10 2.5 Wiring 2.5.1 Contactor Box Harness Assembly, 12-Pin (Control) 2.5.2 Contactor Box Harness Assem bly, MDI, 6-Pin (Left Element) BLUE BLACK 1 2 3 4 5 6 BLACK BLACK BLUE BLUE PN 106-8744 2.5.3 Contactor Box Harness Assem bly, MDI, 9-Pin (Right Element) BLUE BLACK 1 2 3 4 5 6 BLACK BLACK BLUE BLUE 7 8 9 PN 106-8745 2.
2-11 2.5.5 Main Wiring Harnesses 2.5.6 Component Box and Filter Pump 1 2 ITEM PART # COMPONENT 1 106-5750SP Full Vat Control Harness J4 to J2 (Standard) 2 106-5935SP Filter Pump C2 to Component Box Wi.
2-12 2.6 Filtration System Components.
2-13 2.6 Filtration System Components (cont.) I T E M PART # COMPONENT 106-9313 Filter Pan Assembly 1 823-7086 Filter Pan 2 220-4446 SanaGrid Filter Screen 3 810-3414 Ring, Wireform Holddown 4 824-1957 Crumb Basket * 826-1392 O-ring (Pkg.
2-14 2.7 Frypot and Associated Parts 1 2 5 6 4 3 7 8 9 F r o n t o f F r y p o t I T E M PART # COMPONENT Frypot Assembly 1 823-6706 Frypot 2 807-0128 Bushing, Insulating, Heyco 3 220-4564 H a n d l e.
2-15 2.8 Wiring Connectors and Pin Connectors ITEM PART # COMPONENT 1 807-1068 2-Pin Female 2 807-2136 6-Pin Female, Hi Amp 3 807-2138 9-Pin Female, Hi Amp 4 807-0159 12-Pin Female 5 807-0875 15-Pin F.
2-16 2.9 Fasteners (Nuts, Bolts, Screws, Washers) ITEM PART # COMPONENT * 809-0514 Capscrew, 5/16-inch-18 NC Hex * 809-0448 Clip, Tinnerman * 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25) (809-0237) * 809-0247 Nut, 8-32 Keps Hex * 826-1376 Nut, 10-32 Keps Hex (Pkg.
THIS PAGE INTENTIONALLY LEFT BLANK.
Frymaster, L.L.C 8700 Line Avenue, Shreveport, Louisiana 7110 6 TEL 1-318-865-1711 FAX (Parts) 1-31 8-219 -7140 (Tech Support) 1-318-2 19-7135 819-6428 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1-8.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Frymaster 8196428 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Frymaster 8196428 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Frymaster 8196428 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Frymaster 8196428 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Frymaster 8196428, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Frymaster 8196428.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Frymaster 8196428. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Frymaster 8196428 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.