Manuale d’uso / di manutenzione del prodotto G4815 del fabbricante Fisher-Price
Vai alla pagina of 16
G4815 Instructions Bounce ‘n Go ™ Coupe Please read these instructions carefully and identify all parts before assembly . Refer to the parts and fasteners pages for identification. Keep this instruction sheet for future reference, as it contains important information.
2 Parts Handle/Canopy Notes: • Some parts shown are assembled to both sides of the coupe. • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry cloth before assembling this product.
3 W arning and Caution CA UTION W ARNING T o av oid serious injury: • Adult supervision required. • Never use near cars and other motor vehi- cles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools, or other bodies of water .
4 1 • Place the frame upside down on a flat surface. Make sure the steering linkage assembly is fitted to the front end of the frame. • Remove the tape holding the front axles to the frame. Rotate the front axles out. 2 • Push the front axles down into the groove in each end of the steering linkage.
5 5 • Fit an axle cover over the cap nuts and to the front end of the frame. Push down on the axle covers to “snap” them into place. Hint: Y ou may need to carefully tap the axle covers with a hammer to secure in place. Axle Covers 6 • Slide a 5 / 16 " washer onto a front axle.
6 9 • Fit a .354" cap nut onto the end of the front axle. • Cover the cap nut with the assembly tool. T ap the cap nut assembly tool with a hammer to secure the cap nut to the front axle. • Pull on the small, front wheel to be sure it is secure on the front axle.
7 13 • Slide the smooth end of the rear axle into the hole in one side of the bouncer base/spoiler , a frame bushing, the frame, the other frame bushing and out through the hole in the other side of the bouncer base/spoiler .
8 17 • Fit an axle cover to the large, rear wheel, as shown. • Push the axle cover to “snap” it into place. Hint: Y ou may need to carefully tap the axle cover with a hammer to secure in place. • Repeat assembly steps 13-17 to assemble an axle bushing, large, rear wheel, wheel bushing, .
9 Assembly 21 • Lift the front end of the vehicle. • Insert the straight end of the steering column up through the hole in the frame. 23 • Fit the steering wheel onto the turn signal and the steering column. 24 • Fit a .354" cap nut onto the end of the steering column.
10 26 • Fit the sound box inside the center of the steering wheel. Assembly 27 • Fit the top edge of the sound box cover into the groove in the steering wheel. • “Snap” the sound box cover into the center of the steering wheel. Sound Box Sound Box Cover • Loosen the screws in the sound box battery compartment door .
11 Assembly 30 • Insert the upper post into the lower post. 31 • Fit the grip halves to the post assembly , over the latch halves. • Insert three #6 x 1 / 2 " screws into the grip halves to join all three parts together . Tighten the screws.
12 32 • Position the post so that the lower bend is toward the front end of the coupe. • Insert the post into the column on the back of the coupe. 33 • Insert the #10 x 2 1 / 8 " bolt into the column on the back of the coupe. • Tighten the bolt.
13 Seat Adjustment • Place the seat onto the coupe into either of two positions – front or back . • Have your child sit on the seat and check the distance between your child’s feet and the pedals. Now , move the seat closer to or further from the pedals .
14 • Locate the sliding latches inside the bouncing base/spoiler . While lifting both sliding latches on the bouncing base/spoiler , rotate the bouncing base/spoiler down . Continue to rotate the bouncing base/spoiler down until it “snaps” into place.
15 • Locate the sliding latches inside the bouncing base/spoiler . While pushing both sliding latches on the bouncing base/spoiler down , rotate the bouncing base/spoiler up . Continue to rotate the bouncing base/spoiler up until it “snaps” into place.
Care • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy . • Do not leave this toy outside in the rain. W ater inside the soundbox could cause it to malfunction. • This toy has no consumer replaceable parts.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Fisher-Price G4815 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Fisher-Price G4815 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Fisher-Price G4815 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Fisher-Price G4815 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Fisher-Price G4815, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Fisher-Price G4815.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Fisher-Price G4815. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Fisher-Price G4815 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
