Manuale d’uso / di manutenzione del prodotto FA848C del fabbricante First Alert
Vai alla pagina of 33
H H a a r r d d w w i i r r e e d d / / W W i i r r e e l l e e s s s s S S y y s s t t e e m m F F A A 8 8 4 4 8 8 C C User Guide N9939 7/00 PRELIMINARY Previous Menu.
- 2 - Table Of Contents QUICK REFERENCE .................................................................................................. 3 INTRODUCTION .................................................................................................
- 3 - Quick Reference TO TURN SYSTEM ON 1. Check to make sure the system is ready, The On/Off ( ARM ) light will light (Green READY light is lit). 2. Enter your 4-digit user code. 3. Exit through a door designated by your installer as an exit/entry door.
- 4 - Quick Reference The following table lists the “Quick Commands” available with this control. Key Description Keypads Comments # 1 Quick Arm - If system is ready All keypads Allows you to arm the system without requiring your user code. User code is always needed to disarm the system, though.
- 5 - Introduction Congratulations on your decision to protect your home or business with the OMNI-848 security system. You have chosen a reliable, state-of-the-art security system that is remarkably easy to operate.
- 6 - System Reference ZONE DESCRIPTIONS In the following table, enter a description of the area of protection for each zone. Example: Zone 1 Windows on North side of building Zone 4 Main entrance to building.
- 7 - System Reference ( cont) SEND-HELP ALERT All keypads are equipped with emergency-pair keys. In order to activate the alert, both keys must be pressed at the same time. The type of keypad you have installed dictates which keys you press. Your installer will show you how to activate these emergency keys.
- 8 - System Reference ( cont) USER CODE ASSIGNMENTS In the following table, enter the names of the individuals assigned to each user number. User Assigned To… User Assigned To… 1 33 2 34 3 35 4 3.
- 9 - Turning The System On IS THE SYSTEM READY? You can turn the burglar portion of your security system on and off. Before you can turn the system on, it must be “ready.” If you have a protected door open, or someone is moving in view of a motion detector, the system will not display “ READY .
- 10 - NOT READY PART 1 and.
- 11 - Turning The System On (cont) Determine which zone or zones are not ready, resolve the problem, and turn the system on normally. If the problem cannot be resolved, you may bypass the zone that is not ready. Bypassing should only be done if the problem on the zone cannot be resolved, OR if you intentionally wish to leave the zone off.
- 12 - NOTE: This system can be programmed by the installer for the AUTOSTAY feature which automatically bypasses interior zones if you arm the system and do not exit through a delay zone during exit time.
- 13 - Turning The System On (cont) TO TURN THE SYSTEM ON IN INSTANT MODE In INSTANT mode, all alarm sensors including doors that normally have a delay to allow you to turn the system off will report an alarm immediately if activated. Check to make sure the system is ready.
- 14 - † If the Quick Bypass feature has been enabled by the installer, do not enter the user code when unbypassing zones..
- 15 - Turning The System Off When you turn the system off, you turn off only the burglar portion of your system; any smoke or heat detectors and panic keys will remain on. You must enter through a designated entry door and turn off the system within the time allowed.
- 16 - User Codes TO ADD OR CHANGE A USER CODE Users can be added or changed directly at the keypad. Your system can have up to 64 different user codes, with each assigned to one of four authority levels and to a primary partition. The authority level determines the functions that user can perform.
- 17 - Miscellaneous Commands SEND HELP ALERTS Your system can be programmed for 3 separate keypad Send Help alerts that would send an emergency signal to your central station. See the System Reference sheet to see which have been programmed for your system.
- 18 - NOTE: Temporary users (i.e. baby sitters, housekeepers, etc.) should not be shown the Bypass procedure..
- 19 - Miscellaneous Commands (cont) QUICK EXIT Restarts exit delay time if the system is already armed. This allows someone to leave after the system has been armed, without having to disarm the system first. To restart the exit delay time, press : STAY .
- 20 - Miscellaneous Commands ( cont) TO VIEW AUTOARM TIME To view the autoarm time for the partition to which the keypad is assigned, press: # [52] [user code with authority level 1 or 2]. AUTOARM TIME: 05:00PM (The user code is not required if so programmed by installer.
- 21 - Using a Pager If programmed, the system can send messages to a pager. The messages display as follows: ACCT E XXX where: "ACCT" = the 4-digit central station no. 2 account number. "E" = is the event code. There are 4 event types: alarms, troubles, openings, and closings.
- 22 - pause is optional and is not required to enter your pager phone number.) If the [Code] key was pressed, it counts as one character. The keypad will emit a single acknowledgement chirp as each number is pressed. 3. Press the [#] key after you have made your pager phone number changes.
- 23 - Testing The System SYSTEM TEST It is recommended that you test your system once a week using the following procedure: NOTE: If your system is monitored, contact your central station before you perform this test. 1. Turn your security system on.
- 24 - Recommendations On Smoke Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association’s (NFPA) Standard #72 noted below.
- 25 - Emergency Evacuation Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants.
- 26 - Glossary AC INDICATOR: Small green power on-off light between the center buttons on the keypad. When lit, the system is running on primary power; when not lit, the system is running off the backup battery. ALARM: Sound from keypad or other horn/siren indicates a burglar alarm, fire alarm, or other condition you should be alerted to.
- 27 - Your system supports two entry times, allowing you to have a different length of time for different doors..
- 28 - Glossary (cont) EXIT DELAY: The period of time allowed between turning the system on and leaving through a designated exit/entry door before the system will register an alarm condition. This is determined at the time of installation. INTERIOR ZONE: An interior zone is a group of points that protect the interior of your premises.
- 29 - Glossary (cont) SILENT CONDITION: Most types of alarms and troubles alert you with the keypad sounder and the sirens, horns, or speakers located in your premises. The intent is to advise you of the alarm or trouble and allow you to respond promptly.
- 30 - FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your inf.
- 31 - LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary, fire, or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.
- 32 - LIMITATIONS OF THIS ALARM SYSTEM (cont) Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers who are located on the other side of closed or partly open doors.
LIMITED WARRANTY First Alert Professional Security Systems .,. a subsidiary of Pittway Corporation, and Pittway Corporation, its divisions, subsidiaries and affiliates ("Seller"), 175 Eileen.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il First Alert FA848C è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del First Alert FA848C - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso First Alert FA848C imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul First Alert FA848C ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il First Alert FA848C, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del First Alert FA848C.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il First Alert FA848C. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo First Alert FA848C insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
