Manuale d’uso / di manutenzione del prodotto AN-2030 del fabbricante Finisar
Vai alla pagina of 35
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 1 1 Application Note AN - 2030 2 Digital Diagnostic Monitoring Interface 3 for SFP Optical Transceivers 4 5 1.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 2 1 3. Enhanced Digital Diagnostic Interface Definition 2 3 Overview 4 5 The enhanced digital diagnostic interface is a superset of the MOD - DEF interface 6 defined in the SFP MSA document dated September 14, 2000.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 3 1 Figure 3.1: Digital Diagnostic Memory Map 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Specific Data Field De scriptions 38 39 The information in italics in Table 3.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 4 Table 3.1 Serial ID: Data Fields – Address A0 1 Data Address Size (Bytes) Name of Field Description of Field BASE ID FIELDS 0 1 Identifier Type of serial transceiver (see table 3.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 5 Identifier 1 The identifier value sp ecifies the physical device described by the serial information. 2 This value shall be included in the serial data.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 6 1 TABLE 3.3: Connector values 2 Value Description of connector 00h Unknown or unspec.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 7 Transceiver 1 The following b it significant indicators define the electronic or optical interfaces that are 2 supported by the transceiver.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 8 The SONET compliance code bits allow the host to determine with which specifications 1 a SONET transceiver complies. For each bit rate defined in Table 3.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 9 BR, nominal 1 The nominal bit rate (BR, nominal) is specified in units of 100 Megabits per second, 2 rounded off to the nearest 100 Megabits per second.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 10 transceiver technology. It is common for the trans ceiver to support both 50 micron and 1 62.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 11 Vendor Rev 1 The vendor revision number (vendor rev) is a 4 - byte field that contains ASCII 2 characters, left - aligned and padded on the right with ASCII spaces (20h), defining the 3 vendor’s product revision number.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 12 Options 1 The bits in the option field shall specify the options implemented in the transceiver as 2 described in table 3.6. Standard Finisar SFP transceivers do not implement TX_FAULT 3 or RATE_SELECT, so byte 65 set to 00010010b .
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 13 1 Date Code 2 The date code is an 8 - byte field that contains the vendor’s date code in ASCII 3 characters. The date code is mandatory.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 14 Table 3.8: Diagnostic Monitoring Type 1 Data Address Bits Description 92 7 Reserved for legacy diagnostic implementations. Must be ‘0’ for compilance with this document.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 15 Enhanced Options 1 “Enhanced Options” is a 1 byte field with 8 single bit in dicators which describe the 2 optional digital diagnostic features implemented in the transceiver.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 16 1 Table 3.10: I/O Timing for Soft Control & Status Functions 2 Parameter Symbol.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 17 1 Diagnostics 2 2 wire serial bus address 1010001X (A2h) is used to access measurem.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 18 calibrated to absolute units using the most representative fiber output type. 1 Accuracy is ±3dB. Data is not valid when the transmitter is disabled.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 19 External Calibration 1 Measurements are raw A/D values and must be converted to real units using calibration 2 constants stored in EEPROM locations 56 – 95 at 2 wire serial bus address A2h (see 3 Table 3.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 20 5) Measured received optical power.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 21 Calibration Constants 1 2 TABLE 3.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 22 The slope constants at addresses 76, 80,84, and 88, are unsigned fixed - point binary 1 numbers. The slope will therefore always be positive.
AN - 2030: Digital Diagnostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 23 1 Table 3.16c: IEEE - 754 Single - Precision Floating Point Number Format 2 FUNCTIO.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 24 Real Time Diagnostic Registers TABLE 3. 17 : A/D Values and Status Bits (2 Wire Address A2h) Byte Bit Name Descriptio n Converted analog values.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 25 110 1 LOS Digital state of the LOS Output Pin. Updated within 100msec of change on pin. This function is implemented in all Fin isar transceivers with digital diagnostic capability.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 26 Table 3. 18 : Alarm and Warning Flag Bits (2 - Wire Address A2h) Reserved Optional Alarm and Warning Flag Bits 112 7 Temp High Alarm Set when internal temperature exceeds high alarm level.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 27 Bytes 123 – 126 contain write - only RAM for entry of a 32 bit password that allows access to user writable EEPROM at locations 128 - 247.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 28 4. DDTC Electrical Interface Definition Overview The Digital Diagnostics Transceiver Controller (DDTC) IC manages all system monitoring functions in the SFP transceiver module.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 29 2 - Wire Interface Reset : After any interruption in protocol, power loss, or system reset, the following steps reset the DDTC . 1. Clock up to nine cycles.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 30 Acknowledge Polling : Once the internally - timed write has started and the DDTC inputs are disabled, acknowledge polling can be initiated.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 31 Detailed 2 - Wir e Serial Port Operation This section gives a more detailed description of 2 - wire theory of operation.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 32 Within the bus specifications a regular mode (10 0 kHz clock rate) and a fast mode (400 kHz clock rate) are defined. The DDTC works in both modes.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 33 of the command/control byte (R/W) defines the operation to be performed. When set to a 1 a read operation is selected, and when set to a 0 a write operation is selected.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 34 DC ELECTRICAL CHARACTERISTICS ( Vcc = 3.15V to 3.60V) PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES Input Leakage (SDA, SCL) I LI - 1 +1 µ A 2 Input Logic 1 (SDA, SCL) V IH 0.
AN - 2030: Digital Diagn ostic Monitoring Interface for Optical Transceivers F i n i s a r 9/26/02 Revision D Page 35 For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089 - 1133 Tel. (408) 548 - 1000 Fax (408) 541 - 6138 sales@finisar.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Finisar AN-2030 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Finisar AN-2030 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Finisar AN-2030 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Finisar AN-2030 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Finisar AN-2030, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Finisar AN-2030.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Finisar AN-2030. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Finisar AN-2030 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
