Manuale d’uso / di manutenzione del prodotto HD4000 del fabbricante 888 Digital
Vai alla pagina of 27
HD4000.
.
1 Safety Instructions • Always read the safety instructions carefully • Keep this User's Manual for future reference • Keep this equipment away from humidit y • Place this equipment on a reli abl e flat surface before setting it up. • Do not stand it on soft furnishings.
2 T able Of Content s Introduction ............................................................................................ 3 Front panel and rear panel illustration ................................................. 4 Front P anel ................
3 Introduction This DVB-T TV Receiver is a Free-T o-Air di gital terrestrial receiv er, allo wing you to access free-to-air digital terrestrial TV channels an d radio broadcasts on your T V set.
4 Front panel and rear panel illustration Front Panel ① ① Green Light To indicate the Stand-by mode ON/OFF (this mode is co ntrolle d by remote control only). Rear Panel ① ANT I N con nect the antenna here. ② LOOP OUT To connect a RF signal from the STB to either the RF Input jack (antenna) on your VCR or to the antenna inp ut of your TV.
5 Remote control Remote key functions: 1. POWER To turn the Stand-by mode ON/OFF. 2. INFO To display the current program information. 3. Numeric buttons (0-9) To control the numerical operation and es pecially to change program directly. 4. SUBT To switch the close caption ON/OFF.
6 Installing the batteries Remove the battery cover fr om the remote control and put two AAA size batteries inside the compartment. The diagram inside the battery compartment shows the correct way to install the batteries. Caution: 1. Keep batteries out of children’s reach.
7 Installation and Connections How to get good reception • In general you are not required to change the existing antenn a. However if your antenna is not in good condition you shou ld consider replacing them to ens ure uninterrupted digital televis ion viewing.
8 Installation and Connections Connect the STB receiver via YPbPr output and Audio output (for high definition viewing) Connect the STB recei ver via VG A output and Audio outp u t (for high definitio.
9 Installation and Connections Connect the recei ver via HDMI output (for high definition viewing) Audio connect ions via Optic al/Coaxial/Mixed A udio L/R Output.
10 First time installation Note: Be sure to turn o n the main power at the rear of your receiver before using the receiver. After all the connections have been made pr operly, switch on your TV . Make sure the receiver is connected to the mains and press Power to switch the receiver on.
11 Basic operations Switch program 1. Press the NUMERIC keys (0~9) on the remote con trol to select the channel number you want. 2. Press the ▲▼ key on the r emote contr ol or the fr ont panel t o change th e availa ble channels upward /downward. 3.
12 Basic operations Change video output mode Press OUTPUT key to select the matched video monitor be tween YPbPr and VGA. Change TV/Radio mode Press TV/Radio key to change the program list mode between T V and Radio. View program info 1. Press INFO key to view the detailed information of current program.
13 Basic operations EPG (Electric Program Guide) 1. Press EPG key to view the EPG information that are provided by the content providers. 2. Press ▲▼ key to view the event information such as event name, event time. . 3. Press OK key to view the detailed information of the current event.
14 Main menu This section guides you to w alk thro ugh of all o ptions on the Menu screen Navigation in the main menu 1. Press MENU key to bring up the main menu or return previo us. 2. Press ▲▼ key to move upward/down to the desired sub menu. 3. Press OK key to enter into the sub menu y ou select.
15 Main menu Menu Tree Inst allation Scan selected channels Auto scan Program Edit Edit F A V Browse Lock Skip Delete Rename Move System Setup A/V setting Local time setting System information Factory.
16 Installation Auto Scan 1. Go to Main menu > Installation. 2. Press BLUE key to auto scan all the channels. 3. Press EXIT key if you want to stop during the auto scan. Manual Scan 1. Go to Main menu > Installation 2. Press ▲▼ to select the channels you want to scan.
17 Program edit NOTE: If there is no prog ram stored, you c an not access the edit menu. Edit Favourite 1. Go to Main menu > Program edit > TV or Radio list. 2. Press YELLOW key to show the favorite list and then press ▲▼ key to select the desir ed favorite list, press OK key to enter favo rite edit mode.
18 Program edit Delete Program 1. Go to Main menu > Program edit > TV or D key to show a list of Edit modes. ion. . cel the operation. T enu. ename menu > Program edit > TV or Radio list. ress ▲▼ key to select the y to enable the rename function.
19 System setup A/V Output Settings 1. Go to Main menu > Sys tem setup > A/V output setting. output, Scree n aspect, key to confirm. ll 2. Press ▲▼ key to select the options: Resolution, Video Audio output. And press OK to enter submenu of select ed option.
20 User preferences OSD Language Go to Main menu > User preferences > OSD language. Only English is supported for this receiver. OSD Transparency 1. Go to Main menu > User preferences >OSD T ransp arenc y . 2. Press ▲▼ key to select the OSD Transparenc y option, and press OK key to enter submenu.
21 User preferences Parental Control User preferences sele ct the Parental Control option, . Parental Rating l. are available. l guidance year old r old ar old d . Installatio n Menu n Menu . Channel Edit Menu el Edit Menu . Setup Menu etup Menu . User preferences Menu s Menu .
22 Trouble shooting If you experience problems with this receiver or its install atio n, in the first instance roblem Possible cause What to do please read carefully the relev ant sections of this User Manual and this Troubleshooting section.
23 Technical specifications em Specification It Frequency Range o 230MHz VHF: 174MHz t UHF: 470MHz to 862MHz Input Impedance 75Ohms unbalanced Signal Input Level -78~-25dbm T uner Bandwidth 7MHz Demod.
WARRANTY INFORMATION PLEASE NOTE THA T DIGIT AL PRODUCTS GROUP PTY L TD ACT AS THE W ARRANTY AND SER VICE AGENTS FOR THIS Digitel+ PRODUCT . DO NOT RETURN THIS CARD TO DIGIT AL PRODUCTS GROUP IMPORT ANT PLEASE KEEP WARRANTY CARD, PROOF OF PURCHASE AND USER MANUAL IN A SAFE PLACE AS YOU WILL REQUIRE THESE WHEN M AKING A WARRANTY C LAIM.
WARRANTY CONDITIONS 1. Where required by DIGITEL+ / DPG only the original invoic e/receipt is sued by e dealer will be accepted as proof of purchase. covers only defects in the material and workmanship of the product r a period of 12months from t he date of original purchas e.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il 888 Digital HD4000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del 888 Digital HD4000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso 888 Digital HD4000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul 888 Digital HD4000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il 888 Digital HD4000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del 888 Digital HD4000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il 888 Digital HD4000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo 888 Digital HD4000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
