Manuale d’uso / di manutenzione del prodotto PowerLite Pro G6150 del fabbricante Epson
Vai alla pagina of 269
PowerLite ® Pro G6050W/G6150/G6450WU/G6550WU/ G6750WU/G6800/G6900WU User's Guide.
.
Contents PowerLite ® Pro G6050W/G6150/G6450WU/G6550WU/ G6750WU/G6800/G6900WU User 's Guide ....... 9 Introduction to Your Projector .................................................................................................................
Connecting to a Component-to-VGA Video Source .................................................................. 37 Connecting to an S-Video Video Source ................................................................................... 37 Connecting to a Composite Video Source .
Setting Up Monitoring Using SNMP ................................................................................................... 75 Controlling a Networked Projector Using a Web Browser .............................................................
Color Mode ....................................................................................................................................... 118 Changing the Color Mode ............................................................................
Viewing Scheduled Events .......................................................................................................... 150 Editing a Scheduled Event..........................................................................................
Solutions When "Not Supported" Message Appears ................................................................... 196 Solutions When Only a Partial Image Appears ............................................................................ 196 Solutions When the Image is Not Rectangular .
PowerLite ® Pro G6050W/G6150/G6450WU/G6550WU/ G6750WU/G6800/G6900WU User's Guide Welcome to the PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU/G6800/G6900WU User's Guide .
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information.
Easy-to-use setup and operation features • Interchangeable bayonet lens options available • Project images side by side from two separate input sources • Create one large seamless display when p.
1 Projector with standard zoom lens 1 2 Cable cover 3 Cable clip 2 4 Remote control 5 Remote control batteries (two AA alkaline) 6 Power cord 7 VGA computer cable 8 Lens unit screw 9 Projector documen.
2 2 clips included with the PowerLite Pro G6800/G6900WU models Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To connect a computer through its VGA port to the projector's BNC ports, you need a VGA-to-5-BNC cable or adapter.
Option or part Part number Genuine Epson replacement lamp (ELPLP76) V13H010L76 Air filter (ELPAF43) V13H134A43 Quick Wireless Connection USB key (ELPAP09; PowerLite Pro V12H005M09 G6050W/G6150/G6450WU.
Option or part Part number HDMI audio video cable 12 feet (3.6 m) length AV22300-12 Short throw zoom lens (ELPLU01) V12H004U01 Rear projection wide lens (ELPLR03) V12H004R03 Standard zoom lens (ELPLS0.
Registering also lets you receive special updates on new accessories, products, and services. Parent topic: Projector Features Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury.
Projector Parts - Interface Ports Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Exh.
7 Wireless LAN indicator light (PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU) 8 Air filter/intake vent 9 Speaker (PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU) 10 Air filter cover latch 11.
Parent topic: Projector Part Locations Projector Parts - Interface Ports 1 Audio1 port 2 Computer port 3 BNC ports 4 Audio2 port 5 RS-232C port 6 Remote port 7 Audio L-R ports 8 Video port 9 S-Video p.
16 Network LAN port 17 SDI port (PowerLite Pro G6900WU) 18 Service port Parent topic: Projector Part Locations Projector Parts - Base 1 Front adjustable foot 2 Rear feet 3 Screw holes for cable cover .
4 Security cable attachment point 5 Mounting bracket holes 6 Screw hole for lens unit release button Parent topic: Projector Part Locations Projector Parts - Control Panel 1 Power button 2 Source Sear.
Parent topic: Projector Part Locations Related references Projector Light Status 22.
Projector Parts - Remote Control 23.
1 On button (turns power on) 2 Standby button (turns power off) 3 Source buttons (changes input source; some buttons may not function depending on the model) 4 Auto button (automatically adjusts posit.
27 Light button (lights up the buttons temporarily) 28 Indicator light (lights up when the remote control is in use) 29 Remote control signal emitter (emits remote control signals) Parent topic: Proje.
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Attaching and Removing the Lens Unit Attaching and Removi.
Front Rear Front ceiling 27.
Rear ceiling Note: Be sure to leave at least 20 inches (50 cm) of space in front of the air exhaust and intake vents and, when setting up multiple projectors, 20 inches (50 cm) of space between the projectors.
• Horizontally : Within the adjustment range of the rear adjustable feet. If you project from the ceiling or from the rear, be sure to select the correct Projection setting and if necessary, turn on the Inv Direction Button setting. If the projector is installed at an angle, be sure to select the Direction setting.
PowerLite Pro G6150/G6800 Standard Zoom Lens - 4:3 Aspect Ratio Screen or Projection distance image size Wide to Tele 1 50 inches 51 to 94 inches (130 to 238 cm) 2 80 inches 83 to 151 inches (211 to 3.
Parent topic: Projector Placement Projector Connections You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound. • Connect any type of computer that has a standard video output (monitor) port, DisplayPort, or HDMI port.
Connecting to a Computer for VGA Video You can connect the projector to your computer using a VGA computer cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.
2. Connect the other end to the projector's HDMI port. Note: If you have problems hearing audio through the HDMI connection, you can use the Audio3 port instead to play sound. Connect one end of an optional 3.5 mm stereo mini-jack audio cable to the projector's Audio3 port and the other end to your computer's audio out port.
Parent topic: Connecting to Computer Sources Connecting to a Computer for 5 BNC Video You can connect the projector to your computer using an optional VGA-to-5-BNC cable. 1. Connect the VGA connector to your computer's monitor port. 2. Connect the 5 BNC connectors to the projector's BNC ports.
2. Connect the other end to the Audio port that corresponds to the Computer or BNC ports you are using. Parent topic: Connecting to Computer Sources Related tasks Connecting to an External Computer Monitor Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
2. Connect the other end to the projector's HDMI port. Note: If you have problems hearing audio through the HDMI connection, you can use the Audio3 port instead to play sound. Connect one end of an optional 3.5 mm stereo mini-jack audio cable to the projector's Audio3 port and the other end to your computer's audio out port.
Related tasks Connecting to a Video Source for Sound Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable.
2. Connect the other end to the projector's S-Video port. Parent topic: Connecting to Video Sources Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable.
2. Connect the other end to the projector's SDI port. Parent topic: Connecting to Video Sources Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports (PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU).
• Connect the red and white plugs on the other end of the cable to the projector's Audio L-R ports. Parent topic: Connecting to Video Sources Related tasks Connecting to an External Computer Mo.
See the documentation that came with the HDBaseT transmitter for instructions on connecting it to your video device or computer. Note: To enable communication from the Ethernet and serial ports on the transmitter, select On for the Control Communications setting in the projector's Extended menu.
Related references Projector Setup Settings - Extended Menu Connecting to External Speakers To enhance the sound from your presentation, you can connect the projector to external self-powered speakers. You can control the volume using the projector's remote control.
Attaching and Removing the Lens Unit Follow the instructions in these sections to attach or remove the lens unit. Attaching the Lens Unit Removing the Lens Unit Parent topic: Setting Up the Projector Attaching the Lens Unit You can attach a compatible lens to the projector.
1 Tighten 2 Loosen 2. Hold the lens unit with the white dot facing up. Insert the lens unit straight into the projector's lens socket and turn it clockwise until you hear it click into place.
3. Insert the screw that came with the projector or the lens unit, and tighten it. This secures the lens unit and prevents it from accidentally being removed. Parent topic: Attaching and Removing the Lens Unit Removing the Lens Unit You can remove the lens unit to replace it with a different lens.
2. Remove the screw securing the lens unit release button. 3. Press and hold the lens unit release button as you turn the lens unit counterclockwise until you hear it click.
Parent topic: Attaching and Removing the Lens Unit Attaching and Removing the Cable Cover You can attach the cable cover that came with your projector to hide the attached cables from view. 1. Bundle the cables together using a band or other fastener (not provided).
3. Tighten both cable cover screws. To remove the cover, loosen both screws and take the cover off of the projector. Parent topic: Setting Up the Projector Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the power and HDMI cables.
2. Insert the end of the cable clip anchors into the cable clip slots near the power inlet and HDMI port. 1 Cable clip slot 2 Cable clip anchor 3 Cable clip 3. Place the open cable clips around the power and HDMI cables, but don't lock them into place.
Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Registering a Digital Cer.
Connecting to a Wired Network Selecting Wired Network Settings Parent topic: Using the Projector on a Network Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network cable. To ensure proper data transmission, use a Category 5e shielded cable or better.
3. Select the Network menu and press Enter . 4. Select Network Configuration and press Enter . 5. Select the Basic menu and press Enter . 54.
6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• If you must set addresses manually, turn off DHCP and enter the projector's IP Address , Subnet Mask , and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control.
Enabling WPA or EAP Security Parent topic: Using the Projector on a Network Related references Optional Equipment and Replacement Parts Installing the Wireless LAN Module To use the projector over a wireless network, install the Epson 802.11b/g/n wireless LAN module (PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU).
3. Remove the screw securing the wireless LAN module stopper, then remove the stopper. 4. Insert the wireless LAN module into the port. 58.
5. Replace the wireless LAN module stopper and secure it using the screw you removed. 6. Close the air filter cover. 7. Plug in and turn on the projector.
3. Verify the correct SSID and IP address is displayed, then remove the wireless LAN module from the projector. 4. Insert the Quick Wireless Connection USB key into the same port used for the wireless LAN module. You see a projected message that the network information update is complete.
8. Follow the on-screen instructions to install the Quick Wireless Connection driver. Note: If you see a Windows Firewall message, click Yes to disable the firewall. After a few minutes, your computer image is displayed by the projector. If it does not appear, press the LAN button on your projector remote control or restart your computer.
5. Select the Basic menu and press Enter . 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • Web Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
7. Select the Wireless LAN menu and press Enter . 8. Select the settings on the Wireless LAN menu as necessary for your network. 9. When you finish selecting settings, select Setup complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Wireless LAN System 802.11b/g Sets the type of wireless LAN system the projector is 802.11b/g/n connecting to Connection Mode Quick Selects the type of wireless connection:.
Setting Options Description DHCP On Turns on DHCP if your network assigns addresses automatically; Off set to Off to manually enter the network's IP Address , Subnet Mask , and Gateway Address IP.
2. Make sure AirPort is turned on, then do one of the following: • If your projector is set up on an existing network (Advanced mode), select the network name (SSID). • If your projector is configured for Quick mode, select the SSID you assigned to the projector.
5. Select the Security menu and press Enter . 6. Select a WPA or EAP setting from the drop-down menu. 7. Select the settings on the security menu as necessary for your network. 8. When you finish selecting settings, select Setup complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Passphrase Various passphrases from 8 to For WPA-2-PSK security, selects 32 characters the pre-shared passphrase used on the network EAP Method PEAP For WPA/WPA2-EAP securi.
Setting Options Description RADIUS Server Name Various server names up to 32 For WPA/WPA2-EAP security, characters selects the server name to verify Verify Exp.
2. Make sure the projector is turned on. 3. Start your web browser on a computer connected to the network. 4. Type the projector's IP address into the browser's address box and press the computer's Enter key. You see the Web Control screen and a prompt to enter a user ID and password.
10. When you finish registering the certificate, click Apply to finalize your changes and complete the registration. Digital Certificate Types for Registration via Web Control Parent topic: Registerin.
Specification Description Extension PKCS, P12 Encryption RSA Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512 Key length 512/1024/2048/4096 bit Common name Network host name Organization Optional Password Up .
PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU 73.
5. Enter the IP address for the SMTP Server option. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
Setting Up Monitoring Using SNMP Network administrators can install SNMP (Simple Network Management Protocol) software on network computers so they can monitor projectors. If your network uses this software, you can set up the projector for SNMP monitoring.
5. Select the SNMP menu and press Enter (PowerLite 1945W/1955/1965). 6. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button.
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely. Note: The web setup and control features support Microsoft Internet Explorer 6.
1 Power on button control 2 Input source selection controls (some buttons may not be available depending on the model) 3 Freeze button control 4 A/V Mute button control 5 Page Up and Page Down button controls 6 Closed caption control 7 Volume button controls 8 Source search control 9 Standby button control 6.
Note: If you want to use the Crestron RoomView system when the projector is turned off, you need to adjust the Standby Mode settings in the Extended menu. 1. Press the Menu button. 2. Select the Network menu and press Enter . 3. Select Network Configuration and press Enter .
5. Set the Crestron RoomView setting to On to allow the projector to be detected. Note: Enabling Crestron RoomView disables the Epson Message Broadcast feature in the EasyMP Monitor software. 6. When you finish selecting settings, select Complete or Setup Complete and follow the on-screen instructions to save your settings and exit the menus.
3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box. 4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. Turning On the Projector Turning Off the Projector Selecting the Language for the .
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. The projector's power light turns orange. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode).
Parent topic: Using Basic Projector Features Related references Projector Setup Settings - Extended Menu Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Extended menu and press Enter .
4. Select Display > Screen > Screen Type . You see this screen: 5. Select your screen's aspect ratio and press Enter . 6. Press the Menu button to accept the changes. Note: After changing the Screen Type setting, adjust the aspect ratio for the projected image.
5. Use the arrow buttons on the remote control or projector to adjust the position of the image. 6. When you are finished, press the Menu button. Note: The screen position cannot be adjusted if the Screen Type is set to 16:10 for the PowerLite Pro G6050W, G6450WU, G6550WU, or G6900WU models or 4:3 for the PowerLite Pro G6150 and G6800 models.
2. Slide the lens shift dial lock as shown to release the lock. 3. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary.
1 Center of lens 2 Projected image when lens shift is set in the center 3 V × 67% (PowerLite Pro G6050W/G6450WU/G6550WU/G6750WU/G6900WU); V× 57% (PowerLite Pro G6150/G6800) 4 H × 30% Note: The image cannot be moved to both the horizontal and vertical maximum values.
Follow these guidelines when using lens shift to adjust your images: • When adjusting the image height, position the image lower than where you want it to be and then move it up using the vertical lens shift dial. This will help prevent the image from moving down after adjustment.
Adjustable Settings Using a Test Pattern Parent topic: Using Basic Projector Features Related tasks Setting the Screen Type Adjustable Settings Using a Test Pattern The following image adjustments can be made while the test pattern is displayed. Top menu Submenu/Option Image Color Mode Abs.
1. Turn on the projector and display an image. 2. To adjust the image height, rotate the front foot to extend or retract it. 3. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
3. Select the Settings menu and press Enter . 4. Select the Geometric Correction setting and press Enter . 5. Select the H/V-Keystone setting and press Enter .
Related tasks Displaying a Test Pattern Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. 1. Turn on the projector and display an image.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter . 7. Press the arrow buttons to adjust the image shape as necessary.
3. Select the Settings menu and press Enter . 4. Select the Geometric Correction setting and press Enter . 5. Select the Arc Correction setting and press Enter .
6. Use the arrow buttons on the projector or the remote control to select the corner or side of the image you want to adjust. Then press Enter . 7. Press the arrow buttons to adjust the image shape as necessary.
3. Select the Settings menu and press Enter . 4. Select the Geometric Correction setting and press Enter . 5. Select the Curved Surface setting and press Enter . Note: If you see a confirmation message to continue, press Enter again. You see this screen: 6.
7. Use the arrow buttons on the projector or the remote control to select the area you want to adjust. Then press Enter . Note: To reset your Curved Surface adjustments, press the Esc button for at least 2 seconds to display a reset screen, then select Yes .
Note: If the triangle pointing in the direction you are adjusting the shape turns gray, you cannot adjust the shape any further in that direction. 9. Press the Esc button to return to the Curved Surface menu screen. 10. Repeat the previous three steps as necessary to adjust any remaining image parts.
Note: If necessary, you can fine tune the results of your Curved Surface adjustments using Point Correction. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Rel.
5. Select the Point Correction setting and press Enter . 6. Select the number of grid lines to display and press Enter . 7. Use the arrow buttons on the projector or remote control to move to the point on the grid that you want to adjust. Then press Enter .
Correcting Image Shape with Corner Wall You can use the projector's Corner Wall setting to adjust the shape of an image projected on a surface with right angles, such as a rectangular pillar or the corner of a room (PowerLite Pro G6800/G6900WU). 1.
6. Select the Corner Type setting and press Enter . 7. Select one of the following: • Horizontal Corner when the surfaces line up horizontally • Vertical Corner when the surfaces line up vertically 8. Press the Esc button to return to the Corner Wall menu screen.
10. Adjust the projector's position and use the lens shift option to center the image over the corner of the wall or the point where the two surface areas meet. (The rest of these steps shows Horizontal Corner as the selected Corner Type but the workflow is the same for Vertical Corner.
When Vertical Corner is selected, adjust the left and right areas using the points nearest the center of the image as your reference points. Note: To reset your Corner Wall adjustments, press the Esc button for at least 2 seconds to display a reset screen, then select Yes .
17. When you are finished, press Menu to exit. Note: If necessary, you can fine tune the results of your Corner Wall adjustments using Point Correction.
Parent topic: Using Basic Projector Features Related tasks Displaying a Test Pattern Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.
2. Carefully rotate the distortion ring counter-clockwise until it cannot go any further. Note: Be careful not to shift the short throw lens when adjusting it to prevent the projected image from shifting.
4. Rotate the distortion ring until the area around the edges of the image is also focused. 5. Rotate the focus ring again to focus the entire screen image. 6. If the area around the lens projection axis is out of focus, rotate the distortion ring again to bring the area into focus.
1 49 feet (15 m) 2 ±60° 3 ±20° 4 ±30° 5 +10° to +50° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
4 S-Video port source 5 Networked computer source 6 DisplayPort source 7 HDMI port source 8 SDI port source (PowerLite Pro G6900WU) 9 HDBaseT port source (PowerLite Pro G6750WU/G6800/G6900WU) Parent t.
2. Hold down the A/V Mute button on the remote control for five seconds. The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for five seconds again.
4. Select the Projection setting and press Enter . 5. Select a projection mode and press Enter . 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios.
The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3. To cycle through the available aspect ratios for your input signal, press the Aspect button repeatedly.
Aspect ratio setting Description Native Displays images as is (aspect ratio and resolution are maintained). Parent topic: Image Aspect Ratio Related tasks Setting the Screen Type Color Mode The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types.
3. Press the Color Mode button on the remote control to change the Color Mode. The image appearance changes and the name of the Color Mode appears briefly on the screen. 4. To cycle through all the available Color Modes for your input signal, press the Color Mode button repeatedly.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button.
You must adjust the volume separately for each connected input source. 1. Turn on the projector and start a presentation that includes audio. 2. To lower or raise the volume, press the Volume buttons on the remote control. A volume gauge appears on the screen.
5. Select the Date & Time setting and press Enter . 6. Use the displayed keyboard to enter the date and time. 7. When you are finished, press Menu .
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Stopping Video Action Temporaril.
Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it.
• To pan around the zoomed image area, use the arrow buttons. • To zoom out of the image, press the E-Zoom – button as necessary. • To return to the original image size, press Esc .
Parent topic: Projector Security Features Setting a Password To use password security, you must set a password. 1. Hold down the Freeze button on the remote control until you see the Password Protection menu. This takes about five seconds. 2. Press the down arrow to select Password and press Enter .
6. Press Esc to return to the Password Protection menu. 7. Make a note of the password and keep it in a safe place in case you forget it. Parent topic: Password Security Types Selecting Password Security Types After setting a password, you see the Password Protection menu.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector. You must enter the correct password to use the projector. 1. Hold down the Num button on the remote control while you enter the password using the numeric buttons.
Parent topic: Password Security Types Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature).
6. Select Yes and press Enter . (If you want to change the selected area, select No , press Enter , and repeat the last step.) You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter . You see a prompt asking if you want to save the image as the User's Logo.
Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2. Select the Settings menu and press Enter .
Parent topic: Locking the Projector's Buttons Installing a Security Cable You can install two types of security cables on the projector to deter theft. • Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson.
1. Press the Split button on the remote control. The currently selected input source moves to the left side of the screen. 2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter , select the input source, select Execute , and press Enter .
7. To exit the split screen feature, press the Split or Esc button. Parent topic: Adjusting Projector Features Using Multiple Projectors You can combine the projected images from two or more projectors to create one large image.
Follow the instructions in these sections to setup and project from multiple projectors. Projector Identification System for Multiple Projector Control Adjusting the Position of the Projected Image Fr.
4. Select Projector ID and press Enter . 5. Use the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter . Repeat these steps for all the other projectors you want to operate from one remote control.
3. Hold down the ID button on the remote control while you press the numeric button that matches the projector's ID. Then release the buttons. Note: If you don't know the projector's ID, hold down the ID button and press the Help button to temporarily display the projector's ID on the screen.
Related tasks Displaying a Test Pattern Adjusting the Image Position Using Lens Shift Resizing the Image With the Zoom Ring Correcting Image Shape with Quick Corner Correcting Image Shape with Point C.
• Full Display : Adjusts the image to the projector's screen size as you scale the image 6. Select one or more of the following scaling options and adjust it as necessary: • – or + : Scales.
Adjusting the Lamp's Brightness When projecting with multiple projectors, you must adjust the brightness setting so that all projectors are as bright as the darkest lamp (PowerLite Pro G6050W/G6150/G6550WU/G6750WU/G6800/G6900WU). Note: Even after adjusting the brightness levels, the brightness of each lamp may not match exactly.
3. Select the Multi-Projection setting and press Enter . 4. Select the Edge Blending setting and press Enter . You see this screen: 5. Turn on the Edge Blending , Guide Display , and Pattern Guide settings. Note: If the projected guide is unclear, try changing the Guide Colors setting.
The range should be set so that the displayed guides are at the edges of the overlapping area between the two images. 9. Press Esc to go back to the previous screen. 10. Select the Blend Curve setting (PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU) and select a gradient for the shaded area.
Note: • You cannot adjust the black level when a test pattern displayed. • The brightness and tone of the overlapping areas may differ from the rest of the image even after adjusting the black level. 1. Press the Menu button. 2. Select the Extended menu and press Enter .
5. Select the Black Level setting and press Enter . You see this screen: 6. Select the Area Correction setting and press Enter . The points you can use to set the range for black level adjustments are displayed.
Note: The points displayed differ depending on the edge settings ( Top Edge , Bottom Edge , Right Edge , Left Edge ) and the geometric adjustment method selected. For example, if Left Edge is set and 5 × 5 is selected for the Point Correction setting, you see a screen like this: 7.
9. To move another point, press the Esc button and repeat the previous two steps. 10. When you are finished, press the Esc button twice and select Yes when you see the confirmation message to return to the Black Level menu screen.
2. Select the Extended menu and press Enter . 3. Select the Multi-Projection setting and press Enter . 4. Select the Multi-screen setting and press Enter . You see this screen: Note: Press Enter to toggle between the projected image and the adjustment screen.
Viewing 3D Images Using an optional polarizer and 3D glasses, you can use two projectors to project and view passive 3D images. See the instructions supplied with the optional equipment for setup and use. For optimal viewing, select the 3D Images setting from the Signal menu and select one of the 3D color modes.
5. Select one of the following options: • Load Memory : Overwrites your current settings with saved settings • Save Memory : Saves your current settings to memory (10 memories with different names are available) Note: A memory name that is being used is indicated by a green mark.
Viewing Scheduled Events Editing a Scheduled Event Parent topic: Adjusting Projector Features Viewing Scheduled Events You can view your scheduled events on the calendar displayed on the Schedule Settings screen. A colored rectangular box on the calendar indicates a scheduled event.
4. Press the left or right arrow buttons to highlight the date on the calendar containing the scheduled event you want to edit. 5. Press the up or down arrow buttons to highlight the event you want to edit, then press Esc . 6. Select from the following options: • On/Off : Enable or disable the selected event.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings. Using the Projector's Menus Image Quality Settings - Image.
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter .
To change settings for an input source, make sure the source is connected and select that source. Setting Options Description Color Mode See the list of available Color Adjusts the vividness of image .
Setting Options Description Advanced Various options available Adjusts the gamma levels and intensity of individual hues in the image Auto Iris On Adjusts the projected luminance based on the image brightness Off when certain Color Modes are selected Note: The Brightness setting does not affect lamp brightness.
Note: You can restore the default settings of the Position , Tracking , and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Progressive Off Sets whether to convert interlaced-to-progressive signals Video for certain video image types Film/Auto Off : for fast-moving video images Video : for most .
Setting Options Description Input Signal Auto Specifies the signal type from input sources connected to RGB computer ports Component Auto : detects signals automatically RGB : corrects color for compu.
Setting Options Description DisplayPort EQ Setting 1 Adjusts the input signal level for the device connected to the 2 DisplayPort connector. Change the setting to reduce interference or correct other image problems.
Setting Options Description Geometric Correction H/V-Keystone Adjusts the projected image shape Quick Corner H/V Keystone : lets you manually Arc Correction correct the angles of the (PowerLite Pro ho.
Setting Options Description Power Consumption Normal Selects the brightness mode of the projector lamp Temp Interlock Normal : sets maximum lamp ECO brightness Temp Interlock : automatically dims the .
Parent topic: Adjusting the Menu Settings Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is Front/Ceiling oriented correctly Rear Rear Ceiling Direction Varying levels available Select.
Setting Options Description Standby Mode Communication On Enable this setting to allow the following operations to occur Communication Off when the projector is in standby mode: • Monitor and contro.
Setting Options Description Multi-Projection Brightness Level Select various options when projecting from multiple (PowerLite Pro projectors G6050W/G6150WU/G6550WU/ G6750WU/G6800/G6900WU) Brightness L.
Setting Options Description Display Background — Selects the screen color or logo to display when no signal is received Startup Screen — Controls whether a special screen appears when the projecto.
Setting Options Description High Altitude Mode — Regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) BNC Sync Termination — Sets the termination for the signal .
Setting Options Description Date & Time — Adjusts the projector's system time and date settings Parent topic: Adjusting the Menu Settings Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details (PowerLite Pro Antenna level G6050W/G6150/G6450WU/G65 Projector Name 50WU/G6750WU) SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Net.
Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Information item Description Event ID Displays the application error log. Event ID Code List Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Proje.
Event ID code Cause and solution 0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct. 0894 Communication with unauthorized access point was disconnected. Contact your network administrator.
You cannot reset the following settings using the Reset All option: • Input Signal • User's Logo • Language • Network menu items • Lamp Hours • Password • Multi-screen • Date &.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Cleaning the Air Filter You need to clean the projector's air filter in the following situations: • The filter or vents get dusty. • You see a message telling you to clean it. • The projector's filter light flashes green. 1. Turn off the projector and unplug the power cord.
3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter. 6. Place the air filter back in the projector as shown and push gently until it clicks into place.
Related references Projector Light Status Replacing the Air Filter You need to replace the air filter in the following situations: • After cleaning the air filter, you see a message telling you to clean or replace it • The air filter is torn or damaged You can replace the air filter while the projector is mounted to the ceiling, if necessary.
3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations. 4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover.
Parent topic: Air Filter and Vent Maintenance Related references Projector Light Status Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
3. Use the screwdriver included with the replacement lamp to loosen the screws securing the lamp cover, and then remove the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury.
5. Hold the lamp by its handle and gently pull it out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 6. Gently insert the new lamp into the projector.
Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 7. Push in the lamp firmly and tighten the screws to secure it. 8. Replace the lamp cover and tighten the screws to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Related references Optional Equipment and Replacement Parts Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
3. Insert the batteries with the + and – ends facing as shown. 4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport or ship the projector safely: • Remove any equipment connected to the projector. • Do one of the following: • If you are using the standard zoom lens, keep it installed on the projector.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or S.
1 Power light 2 Lamp light 3 Temperature light 4 Filter light Power light Lamp light Temperature Filter light Status and solution light Green Off Off Off Normal operation. Flashing Off Off Off Warming up. Wait for an image to appear. green Orange Off Off Off Standby or sleep mode.
Power light Lamp light Temperature Filter light Status and solution light Flashing red Off Flashing Off Projector is too hot. orange • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter.
Power light Lamp light Temperature Filter light Status and solution light On Off Off Flashing Low air flow through the projector. orange • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter.
Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Where to Get Help Related tasks Cleaning the Air Filter Replacing the Air Filter Replacing the Lamp Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system.
Solutions to Sound Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Press the A/V Mute button on the remote control to see if the image was temporarily turned off.
Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press the Source Search or Search button and wait a few seconds for an image to appear. • Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary.
4. Select the Mirror Displays checkbox. Parent topic: Solutions When "No Signal" Message Appears Solutions When "Not Supported" Message Appears If the "Not Supported" message appears, try the following solutions: • Make sure the correct input signal is selected on the Signal menu.
Supported Video Display Formats Related tasks Setting the Screen Type Adjusting the Image Position Using Screen Position Solutions When the Image is Not Rectangular If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible.
Related references Input Signal Settings - Signal Menu Supported Video Display Formats Related tasks Displaying From a PC Laptop Displaying From a Mac Laptop Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus.
Solutions When the Image Brightness or Colors are Incorrect If the projected image is too dark or light, or the colors are incorrect, try the following solutions: • Press the Color Mode button on the remote control to try different color modes for the image and environment.
• If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac supports audio through the HDMI port. If not, you need to connect an audio cable.
• If the projector's lamp shuts off and the power and Temp lights are red, the projector has overheated and shut off. Check the solutions for this light status.
Optional Equipment and Replacement Parts Remote Control Operation Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dime.
PowerLite Pro G6150 : Normal or Temp Interlock Power Consumption mode: White light output 6500 lumens (ISO 21118 standard) Color light output 6500 lumens ECO Power Consumption mode: White light output.
PowerLite Pro G6800 : Normal or Temp Interlock Power Consumption mode: White light output 7000 lumens (ISO 21118 standard) Color light output 7000 lumens ECO Power Consumption mode: White light output 4900 lumens (ISO 21118 standard) Contrast ratio 5000:1 with Auto Iris on and Normal Power Consumption mode Image size 50 inches (1.
Noise level PowerLite Pro G6050W/G6150/G6550WU : 37 dB (Normal Power Consumption mode) 31 dB (ECO Power Consumption mode) PowerLite Pro G6450WU : 34 dB (Normal Power Consumption mode) 31 dB (ECO Power.
Lamp life PowerLite Pro G6050W/G6450WU : Normal Power Consumption mode: Up to about 3000 hours ECO Power Consumption mode: Up to about 4000 hours PowerLite Pro G6150/G6550WU : Normal Power Consumption.
Width 19.9 inches (505 mm) Depth 15.0 inches (382 mm) Weight PowerLite Pro G6050W/G6150/G6450WU/G6550WU/G6750WU : (with standard lens and without 21.5 lb (9.7 kg) cable cover) PowerLite Pro G6800/G6900WU : 21.3 lb (9.6 kg) Standard lens is approximately 1.
Power consumption Operating: (100 to 120 V) PowerLite Pro G6050W : Normal Power Consumption mode: 498 W ECO Power Consumption mode: 421 W PowerLite Pro G6150/G6550WU : Normal Power Consumption mode: 5.
Power consumption Operating: (220 to 240 V) PowerLite Pro G6050W : Normal Power Consumption mode: 477 W ECO Power Consumption mode: 405 W PowerLite Pro G6150/G6550WU : Normal Power Consumption mode: 5.
Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA+ 60/75 1400 × 1050 WSXGA+ 1 60 1680 × 1050 UXGA 60 1600 × 1200 WUXGA 2, 3 60 1920 × 1200 MAC13" 67 640 × 480 MAC16" 75 83.
Display format Refresh rate (in Hz) Resolution (in pixels) WXGA 60 1280 × 800 60 1280 × 768 4 60 1366 × 768 5 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 WUXGA 2, 3 60 1920 × 1200 SDTV (480i 5 /480p) 60 720 × 480 S.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention device.
For Canadian Users This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs The list of GPL Programs busybox-1.
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or an.
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-read.
For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
Gnomovision version 69, Copyright (c) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type 'show w'. This is free software, and you are welcome to redistribute it under certain conditions; type 'show c' for details.
The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright ©) 1991, 1999 Free Software Foundation, Inc.
have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program.
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License").
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplie.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for.
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.
that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code. The IJG distribution formerly included code to read and write GIF files.
Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant and with the following additions to the disclaimer: There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs.
Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose.
License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows. Copyright notice: (c) 1995-1998 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty.
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable co.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and.
(C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software. (7) Sun Microsystems Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved. Developed at SunPro, a Sun Microsystems, Inc.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS".
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (15) Andrey A. Chernov Copyright (C) 1997 by Andrey A.
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTER.
(19) Todd C. Miller Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com> All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
made to this software or documentation, and that the name of Intel Corporation not be used in advertising or publicity pertaining to distribution of the software or the documentation without specific, written prior permission.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
(30) - Alex Tatmanjants (targets using libc/posix) Copyright (c) 1995 Alex Tatmanjants <alex@elvisti.kiev.ua> at Electronni Visti IA, Kiev, Ukraine. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN .
MIT License This projector product includes the open source software program which applies the terms and conditions provided by owner of the copyright to the "MIT License". The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TOPPERS/JSP This projector product includes the open source software program "TOPPERS/JSP" which applies the terms and conditions provided by owner of the copyright to the "TOPPERS/JSP".
(b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided otherwise. (4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the University of California, Berkeley and its contributors.
(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.
A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Epson PowerLite Pro G6150 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Epson PowerLite Pro G6150 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Epson PowerLite Pro G6150 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Epson PowerLite Pro G6150 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Epson PowerLite Pro G6150, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Epson PowerLite Pro G6150.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Epson PowerLite Pro G6150. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Epson PowerLite Pro G6150 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
