Manuale d’uso / di manutenzione del prodotto LX-300+ del fabbricante Epson
Vai alla pagina of 16
EPSON LX-300+ 5/00 EPSON LX-300+ - 1 User Replaceable Parts Options Single-bin Cut-sheet Feeder (C806371) Feeds up to 50 sheets of ordinary single-sheet paper. Additional Tractor Unit (C800301) Used in combination with the other tractor, improves continuous paper handling and reduces the chance of paper jams.
EPSON LX-300+ 2 - EPSON LX-300+ 5/00 Electrical Environmental Line spacing 1/6 inch or programmable in 1/216-inch increments Printable columns 80 columns (at 10 cpi) Resolution (maximum) 240 × 144 dp.
EPSON LX-300+ 5/00 EPSON LX-300+ - 3 Paper Use recycled paper, envelopes, and single-sheet multipart forms only under normal temperature and humidity conditions, as follows: Temperature: 59 to 77 °F (15 to 25 °C) Humidity: 30 to 60% RH Do not load paper that has been folded or is damaged, wrinkled, or curled.
EPSON LX-300+ 4 - EPSON LX-300+ 5/00 Paper Alignment Printing starts at “0” on the scale. The unprintable area is to the left of the “0”. Printable Area Single sheets and envelopes A The minimum top margin is 0.17 inch (4.2 mm). B The minimum left and right margins are 0.
EPSON LX-300+ 5/00 EPSON LX-300+ - 5 Safety Approvals 120 V Safety standards UL 1950 CSA C22.2 No. 950 EMI FCC part 15 subpart B class B CSA C108.8 class B 230 V Safety standards EN 60950 EMI EN 55022 (CISPR pub. 22) class B AS/NZS 3548 class B Acoustic noise Approx.
EPSON LX-300+ 6 - EPSON LX-300+ 5/00 Selecting Fonts After entering the Micro Adjust mode by holding down the Pause button for three seconds, you can change font settings with the Tear Off button. The two Tear Off lights come on ( n ) and go off ( o ) to show the current selection.
EPSON LX-300+ 5/00 EPSON LX-300+ - 7 Paper Positions Top-of-Form Position The top-of-form position is where the printer starts printing on single sheets or continuous paper. Tear-off Position Continuous paper is in the tear-off position when the perforation is aligned with the tear-off edge.
EPSON LX-300+ 8 - EPSON LX-300+ 5/00 Printing with the Pull Tractor To load continuous paper using the pull tractor, you must move the tractor to the pull tractor position, as described in steps 1 through 4 below. If your tractor is already installed in this position, make sure the printer is off and skip to step 7.
EPSON LX-300+ 5/00 EPSON LX-300+ - 9 7. Slide the left sprocket unit so that its sprockets match the position of the holes in the paper and lock the unit in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it.
EPSON LX-300+ 10 - EPSON LX-300+ 5/00 To adjust the top-of-form position for continuous paper loaded on the pull tractor, see the following example: First mark a point 0.1 inch (2.5 mm) above the paper’s perforation; then position the paper so that the mark is even with the top edge of the plastic ribbon cover.
EPSON LX-300+ 5/00 EPSON LX-300+ - 11 5. After you set the tear-off position, press the Pause button to turn off the Micro Adjust mode. 6. Tear off the printed page(s). When you resume printing, the printer automatically feeds the paper back to the top-of-form position.
EPSON LX-300+ 12 - EPSON LX-300+ 5/00 Adjusting the Paper Thickness Lever Before printing on special paper, you need to change the paper thickness setting. The paper thickness lever is under the cover on the left side of the printer. The numbers next to the lever indicate the thickness setting.
EPSON LX-300+ 5/00 EPSON LX-300+ - 13 Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer’s control panel using the default setting mode.
EPSON LX-300+ 14 - EPSON LX-300+ 5/00 Bidirectional Alignment If you notice that the vertical lines in your printout are not properly aligned, you can use the printer’s bidirectional adjustment mode to correct this problem. To complete the steps below, you need 5 letter or A-4 size single sheets or 5 pages of continuous paper.
EPSON LX-300+ 5/00 EPSON LX-300+ - 15 Cleaning the Printer To keep your printer operating at its best, you should clean it thoroughly several times a year. Follow these steps: 1. Remove any paper loaded in the printer and turn it off. 2. Unplug the power cord from the electrical outlet; then disconnect the interface cable from the printer.
EPSON LX-300+ 16 - EPSON LX-300+ 5/00.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Epson LX-300+ è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Epson LX-300+ - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Epson LX-300+ imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Epson LX-300+ ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Epson LX-300+, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Epson LX-300+.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Epson LX-300+. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Epson LX-300+ insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
