Manuale d’uso / di manutenzione del prodotto FALCON del fabbricante Energizer
Vai alla pagina of 69
USBird HAWK / FALCON / EAGLE8/A / MONO8 / FLEX8C AUDIO / VIDEO RECORDERS USERS MANUAL WINDOWS VERSION RELEASE 5.0 03/02/2007.
1 TABLE OF CONTENTS SECTION PAGE 1 INTRODUCTION ……….………………………………….. 3 1.1 System Requirements 1.2 Installation 1.3 Run Program 1.4 Red LED 1.5 Powered USB Hub 2 SETUP ….…………………………………………………….
2 9.1 PLAYER MAIN MENU BUTTONS 9.2 CREATE A JPEG 9.3 CREATE A SEGMENT 9.4 AVI 9.5 WAV APPENDIX - A USBird SOFTWARE INSTALLATION APPENDIX - B MJPEG CODEC APPENDIX - C WINDOWS MEDIA PLAYER APPENDIX - D .
3 SECTION - 1 INTRODUCTION The USBird support unit code was designed to be simple to use. To keep this manual down in size the obvious settings and displays will not be covered. The term " RECORDER " will be used when referring to the HAWK/4/8/8A, FALCON/4, EAGLE8 /A/B/C/D/E, FLEX8E, and all other ADS recorders with a built in USB port.
4 5- USBird_Manual - a PDF copy of this manual 6- USBird_Install - a PDF instruction guide to load software. For new soft ware installa tion f o llow this order: 1. Install USBird softwar e. Refer to Appendix A. 2. Optional - Windows Media Player 7.1.
5 Figure 1. 3.1 Hardware Wizard Figure 1.3.2 Install Automatically Figur e 1.3.3 Complete Wizard 1. In the Welcome to the Found New Hardware Wizard, select “Y es, this time only.” Refer to Figure 1.3.1 Hardware Wizard 2. Select “ Install the software automatically (Recommended)” Refer to Figure 1.
6 The computer recognize s the RECORDER if the same USB port is always used and the Found New Hardware Wizard will not appear. Attaching the recorder to a brand new USB port for t he first time initiates the Found New Hardware setup. 1.4 RED LED A solid red LED (light) must always appear when RECORDER is connected to the computer.
7 EAGLE8/A/B/C/D/E, MONO8, and FLEX8E use the USBird software. The video settings are disabled once the audi o recorders are connected. Refer to Figure 1- 5 Video Settings Figure 1-5 Video Settings IMPORTANT REMINDER!!! Always press the stop button or set the slide switch to OFF and remove batteries before you attach the RECORDER to the computer.
8 SECTION 2 SETUP The SETUP menu shown in Figure 2-1 appears on startup. Always select CONNECT RECORDER to read the settings of t he attached RECORDER.
9 The APPROXIMATE RECORDING TIME: displays the amount of recording time whether you have audio, video, or both. The RESOLUTION of the camera and VIDEO RATE greatly effect the approximate recording time. The HIGH and LOW Resolution are determined by which camera is currently connected.
10 Figure 2.2.1 ENABLED / SET TIMERS 2. At the TIMER RECORDING START DATE / TIME the TIME is in military (24 Hour) format. Enter the date under TIMER RECORDING START DATE . A calendar appears. Enter the ti me in the TIME section. The TIME activates the recorder.
11 Figure 2.2.2 TIMER MODE Entry Menu NOTE!! The unit automatically resets to MA NUAL Mode after the data transfer. If you uncheck the “ ENABLE box” and choose “APPLY CHANGES”, the unit will revert to Manual. 2.3 ERASE RECORDER The RECORDER data memory MUST always be erased after each use.
12 SECTION 3 UTILITY The UTILITY selection is covered next because the operator may need to define the computer disk drives for the USBi rd program and run maintenance programs for the RECORDER. If you received your computer from ADS the disk drives have been configured.
13 DragtoDisc software is C:Program FilesRoxi oEasy CD Creator 7DragtoDiscDragtoDisc.exe. Refer to Appendix E-4 CHANGE FORMAT UTILITY If the drive is a re-writable MO (Magneto Optical) then the program will automatically use the Windows utility, therefore you do not need to define one.
14 3.5 CLOCK BATTERY EXPIRATION The user may examine the internal Clock Battery expiration date from this men u. Every two years ADS will change the ba ttery and re-test the recorder at no charge. 3.6 UPDATE RECORDER SOFTWARE This button will load the firmw are that is on the hard di sk into the RECORDER.
15 SECTION 4 TRANSFER To transfer the evidence to the archive media (CD/DVD) follo w the steps outlined below: * Set the RECORDER to OFF and remove batteries. U se the USB cable provided by ADS to attach the RECORDER to the computer, 1. Select CONNECT RECORDER to read RECORDER settings and content.
16 Figure 4-2 Select Storage Device After the user chooses DVD WR (D VD burner) or CD WR (CD burner) the CD/DVD Select displays the type of media and which sessions will be transferred. Selecting DVD 1 transfers all the sessions that will fit on the first DVD.
17 will fit on the third CD. CD-R m edia has to be formatted first. Refer to Figure 4-4 CD3 FIGURE 4-4 “CD 3” 4. After the user views their selection in the CD/DVD Select, highlight DVD1 and select TRANSFER .
18 YOU SHOULD NOT USE SPECIAL CHARACTERS AND SPACES IN THE FILE NAME. 5. Enter descriptive info rmation and select Enter. Refer to Figure 4-7 Keyboard 6. Data transfer begins. When the bl ue bars stop, transfer is completed. Refer to Figure 4-8 Transfer complete Figure 4-7 Keyboard The TRANSFERRING DONE displays when dat a transfer has completed.
19 4.1 Definitions of th e Status Abbreviations On the Transfer and Playback screens the STATUS of each session are displayed. Each abbreviation TR, FE, LB, and PF have their own definition. Refer to Figure 4-9 STATUS Figure 4-9 STATUS TR = Transferred session complete The chosen session has transferred properly.
20 4.2 FORMAT CD / DVD WARNING!!! For EVIDENCE you should use a “GOLD” CD/ DVD because cheap media may loose data over time. We recommend “ MITSUI GOLD ”. 1. Select FORMAT button from the Transfer screen. Refer to Figure 4.2.1 SELECT FORMAT 2.
21 Figure 4.2.3 DRAG TO DISC INTERF ACE Figure 4.2.4 FORMATDISC 5. Enter Volume Label, which will be the name given to the CD and select OK. Refer to Figure 4.2.5 VOLUME LABEL Figure 4.2.5 VOLUME LABEL 6. After Format is complete, the Drag to Disc icon will appear with the disk name.
22 4.3 EJECT THE CD / DVD 1. Select EJECT button. Refer to Figure 4.3.1 SELECT BUTTON Figure 4.3.1 SELECT BUTTON 2. Select the DRIVE lett er and select EJECT. Refer to Figure 4.3.2 DRIVE LETTER Figure 4.3.2 DRIVE LETTER 3. Check the boxes of all the three options.
23 FIGURE 4.3.3 EJECT OPTIONS 4.4 COPY Recording from Hard Drive to CD/DVD The numbers in the diagram co rrespond to the direction number. 1. Format blank Media. (CD or DVD) Refer to Section 4.2 FORMAT CD / DVD 2. Go to PLAYBACK Refer to Figure 4.4.1 PLAYBACK S CRE EN 3.
24 Multiple recordings can be transferred together, for example sessions numbered 4,5,and 6 can be copied together since they are in sequential order. I F you wanted to copy sessions 1 and 6 you have to transfer them one at a time. 5. Select the COPY button Refer Figure 4.
25 Figure 4.4.4 Copy in Progress 8. Once the Copy Complete is displayed, check to make sure the recording plays back in the PLAYBACK Menu. Refer to Figure 4.4.5 Copy Complete Figure 4.4.5 Copy Complete 9. Eject and Finalize the CD/DVD through the DragtoDisc program.
26 SECTION 5 PLAYBACK In order to initiate playing video / audio perform the steps outlined below: 1. Select the PLAYBACK button located on the top row. 2. Select the “Source” drive, C, D, E etc in PLAY FROM 3. Select File and Session(s) you desire to listen and watch 4.
27 Figure 5-2 “USBird Player” Menu . Most of the controls are obvious, Windows Media Player Menu . To play from any time, just place the mouse on the “white box” on the time bar and hold the left mouse button down. Drag the arrow to when you want to play and release the mouse button start playing.
28 6. The EJECT button calls the DragToDisc program which finalizes and ejects the CD/DVD 7. The FORMAT button calls the DragToDisc program, which prepares a blank CD/DVD for data transfer. 8. The COPY button transfer files from different storage devices such as hard disk to CD/DVD or CD/DVD to hard disk.
29 Figure 5-4 PLAY RATE The PLAYBACK window can fit the entire screen by removing the PLAYER graphical interface. This is used when the recording is made into an analog copy such as VHS tape. Right cli ck on the PLAYBACK screen and select FULL SCREEN .
30 Analog audio can be made from the USBird recording. First attach an audio tape recording device to the sound card. Use the audio output of the sound card, usually the green conn ector. At the PLAYBACK screen check the box labeled ANALOG COPY . The Select screen appears.
31 DATE AND TIME from Windows Media Player The running time and the date of the AVI recording can be displayed through Windows Media Player by selecting View , Now Playing, Tools , Caption . The date and time of the recordi ng will be displayed at the bottom left of the playback screen.
32 SECTION - 6 HAWK4/8/A / FALCON/4 EAGLE8/A RECORDERS HAWK The HAWK line of recorders can perform both video and or audio recording. The record time is 30 f/s=1.7 HR; 15F/S=3 HR; 5 f/s-8 HR; 1 F/S=17 HR. The HAWK memory expansion cards (up to a total of 8) can be added to the HAWK for longer-term recordings.
33 and stop buttons. The HAWK8/A does not have the local audio playback controls. The HAWK8/A uses the black slide switch to activate the recorder into record mode. The mini USB port on the HAWK8/A is different from the HAWK/4. The new generation HAWK4 uses the slide switch and new mini USB port.
34 FALCON/2 The FALCON is the next generation aud io / video recording device. The FALCON is a slimmer version of the HAWK with more memory. The advantages of the FALCON are you can remove the recorder from the aluminum shell in order to place the recorder in objects where size makes a difference.
35 BATTERY Installation The HAWK uses two 1.5 v, "AA" batte ries for operation. The batteries are installed series providing 3 volts. The HAWK8/A uses 2 and 4 “AAA” batteries. Please note the label in the bottom of the unit for proper battery installation.
36 If the battery is low then t he LED will flash ON and OFF slowly. No red or green LED present the record is not recording. NOTE! If the low battery indicator is flashing, turn the unit “OFF” replace the cells and turn the unit ON or “RCD” again.
37 CAMERA CAMERA RESOLUTION COLOR STRIPES CIF LOW RESOLUTION B/W NONE CIF LOW RESOLUTION COLOR RED VGA HIGH RESOLUTION B/W YELLOW VGA HIGH RESOLUTION COLOR YELLOW/RED MICROPHONE The HAWK/EAGLE8 and FALCON can use its stereo internal or external microphones.
38 Next Generation: Our next generation recorders such as the HAWK/4, HAWK8, FALCON/4 use a black switch that slides into designated modes "ON" and "OFF If the remote record switch is attached to the RECORDER it must be used for ON/OFF control.
39 The playback function uses all 4 switches . NOTE that you must be in the OFF state to re-enter the re cord mode. The REW and FWD switches have different meaning when in PLAY or PAUSE.
40 One Forced Session One Forced Session Full Recording Length CIF (LOW) VGA (HIGH) CIF (LOW) VGA (HIGH) 30 f/s 22 minutes 14 minutes 88 minutes 56 minutes 15 f/s 42 minutes 27 minutes 168 minutes 108.
41 Figure 6-4 HAWK with button descriptions MICRO CAMS SXGA Camera The Micro Cams records at 640X 480 pixels. (High Resolution) The SXGA camera records at 1290 x 960 resolution at 1.3 megapixel. The SXGA is mainly used in stationary applications for example, a pole camera.
42 Low Light Cameras Long Lens, Button, Pinhole Figure 6-5 EAGLE8/ A with descriptions Fi gure 6-6 EAGLE8/Transmitter The Low Light Cameras work well in environment where light is a limited resource.
43 SECTION 7 "MONO8" RECORDER Figure 7-1 MONO8 The MONO8 audio recorder captures stereo for 10 hours or mono for 20 hours. Note that the pager is fully functional with the exception of the vibrator function.
44 SECTION 8 FLEX8F The FLEX8F is our most covert recorder. Th e solid-state electronics built on an untra-thin form factor assures inconspicuous evidence recording in highly transportable packages. Data is transferred to any PC via a Universal Serial Bus (USB).
45 SECTION 9 PLAYER Program The “PLAYER” is similar to our FBPLAYER used on the earlier EAGLE 2 and 4 line. The PLAYER plays audio and video f iles from the recorders however the PLAYER cannot change the settings of the RECORDER. The PLAYER code resides on all evidence CDs inside the HAWK directory.
46 2. The PLAY button, once sessions are chose the PLAY button to go into the PLAY screen. 3. The AVI button converts audio/video re cordings into AVI files. 4. The WAV button converts audio recordings into wav files 5. The EJECT button calls the DragToDisc program which finalizes and ejects the CDDVD.
47 5. The IMAGE button extracts a pi cture frame from the recording 6. The session volume can be adjust ed through the AUDIO L and R channel scroll bars. 7. The PLAY RATE adjusts the frames per second of playback. 8. The PLAY button begins audio and video playback .
48 Figure 9.2.1 Select IMAGE b. Next select the PAUSE button. Refer to Figure 9.2.1 Select IMA GE c. Select the IMAGE button. Refer to Figure 9.2.2 IMAGE Button Figure 9.
49 d. In the SAVE AS screen select the location where to save the JPEG (use the down arrow to navigate through the folders) and input a name for the JPEG in the File name. Refer to Figure 9.2. 3 Save As Screen e. Select Save. Refer to Figure 9.2. 3 Save As Screen Figure 9.
50 into its own individual session. T he SEGMENT is created in the PLAYBACK screen. 1. Create the segment by us ing the scroll bar. Find the beginning of the SEGMENT and select SET. Refer to Figure 9.3.1 Start of SEGMENT Figure 9.3.1 Start of SEGMENT 2.
51 Figure 9.3.2 End of SEGMENT 3. Select the SEGMENT button. Refer to Figure 9.3.3 SEGMENT Button Figure 9.3.3 SEGMENT Button 10. In the CaseIDForm screen the SEGMENT is designated by the SG followed by the original file name and session number. The FILE NAME can be renamed.
52 common user friendly format. An AVI file can be converted to the MJPEG2 format which can be played back on a standar d DVD player. AVIs can also be generated from the USBird Program in the Playback screen. In this demonstration the AVI will be ma de from the PLAYER program.
53 5. Insert a blank CDDVD in the CDDVD-WRITER and select FORMAT. Format the CD using the DragToDisc software. Refer to Section 4.1 Format CD/DVD 6. Select the AVI under CONTENT 7. Select COPY, the AVI file is c opied from Hawk_Temp to the CD/DVD. 8. Select EJECT and close out the CD Figure 9.
54 9.5 WAV A WAV file is created for other programs that recognize the WAV file format such as WINDOWS MEDIA PLAYER. We cove rt our proprietary audio format to a user-friendly format. WAV files can al so be generated from the USBird Program in the Playback screen.
55 A music CD can hold about 70 minutes of audio recording. If you have a two hour recording two CDs are needed. The WAV files are converted and written to the Hawk_Temp Folder. The user chooses where the Hawk_Temp Folder is stored. Refer to Figure 7-5 WAV CONVERSION SCREEN 5.
56 APPENDIX - A USBird SOFTWARE INSTALLATION To install/update the re sident code from CD. 1. Remove existing software from the CONTROL PANEL/ A DD REMOVE PROGRAMS .2. Go to USBird folder and select ‘Setup.exe’. 10. In the Welcome screen, select next.
57 APPENDIX – B MJPEG CODEC Installing MJPEG If the video can not playback insta ll the MJPEG codec. MJPEG Codec compresses the Hawk File so it can be played back through Windows Media Player. 1. Go to the MJPG_CODEC Folder. 2. Select LEAD MCMP_MJPEGCodec.
58 APPENDIX - C WINDOWS MEDIA PLAYER Installing Windows Media Player 7.1 If your computer does not correctly di splay AVI files install new Windows Media Player 7.1. 1. Go to My Comput er and go to USBIRD CD. 2. Select mp71.exe 3. In the Windows Media Play er 7.
59 APPENDIX - D UPDATE BINARY CODE How to update HAWK Binary Code 1. Select Utility button. 2. Select UPDATE RECORDER SOFTWARE . Figure D-1 UPDATE RECORDER SOFTWARE 3.
60 Do not unplug the recorder while it is updating the binary code, this can cause malfunction in the Hawk. Code update takes approximately 40 seconds. 4. After binary code update is complete , select OK at the CODE UPDATED box. Refer to figure D-3 CODE UPDATED BOX.
61 APPENDIX – E SETUP DRIVES 1. Select UTILITY , and select SETUP DRIVES . Refer to Figure E-1 Setup Drives Figure E-1 Setup Drives 2. In Setup Drives select ADD Refer to Figure E-2 Setup Drives Figure E-2 Setup Drives 3. Select drive with corresponding letter, choose TYPE and select OK.
62 Figure E-3 Add Drives 4. If the space is blank, press Change Format Utility button, to select the format program. The path for ROXIO 5 is C:Program FilesAdaptecEasy CD CreatorDirectCDdirectcd.exe. T he path for ROXIO 6 is C:Program FilesRoxioEasy CD Creator 6Dragto DiscDragtoDis c.
63 Figure E-5 New Drive Added 6. Now you can view the drives that were added. Refer to Figure E-6 View Drives Figure E-6 View Drives.
64 APPENDIX - F BATTERY ORIENTATION Proper battery placement is necessary in order for the recorder to function correctly. Use the battery diagram as a guide.
65 APPENDIX - G ADS SOFTWARE CONFIGURATIONS This message was written to clear up some confusion that may exists on the various software and hardware releas es that are out in the field. FBIRDWIN 3.5 (and 3.X) is used with desktops and PDR (not PDR2) stations.
66 APPENDIX - H TROUBLE SHOOTING Most problems can be solved by re ferring to the USBIRD MANUAL. Before you use the recorder, make sure memory has been eras ed. If you press the record button and see three blinking lights you must er ase the recorder memory.
67 APPENDIX – I Micro Cam Installation Mounting a MICROCAM into the concealment is made easy by the items below. The three items are shipped with the MICROCAMS. The items include, a drill bit, a center punch, and camera bezel or frame. MICROCAM Concealment Kit 1.
68 Center Punch and Camera Bezel Drill Bit 5. Place the drill bit inside the cent er punch. The center punch and camera bezel align the camera hole. 6. Once the camera hole is made re move the drill bit and center punch. 7. Replace the center punch with the MICROCAM.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Energizer FALCON è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Energizer FALCON - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Energizer FALCON imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Energizer FALCON ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Energizer FALCON, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Energizer FALCON.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Energizer FALCON. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Energizer FALCON insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
