Manuale d’uso / di manutenzione del prodotto NWS200 del fabbricante 3M
Vai alla pagina of 20
INST ALLA TION AND OPERA TING INSTR UCTIONS NWS RESIDENTIAL W A TER SOFTENERS MODELS: NWS100 NWS100M NWS150 NWS150M NWS200 NWS200M INSTR2208 0110 Installer , please leave with homeowner .
SAFETY INFORMATION Read, understand, and follow all safety informa tion contained in these instructions prior to installation and use of the NWS Series W ater Softener . Retain these instructions for future reference. Failure to follow installation, operation and maintenance instructions may result in property dama ge and will void warranty .
T ABLE OF CONTENTS SECTION DESCRIPTION 1 BEFORE INST ALLA TION 2 INST ALLA TION 3 REGENERA TION INSTRUCTIONS (Timing Setting Instructions) 4 SERVICE INSTRUCTIONS 5 SPECIFICA TION AND OPERA TING DA T A.
Check Y our Pumping Rate and Water Pressure: T wo water system conditions must be check ed carefully to avoid unsatisfactory operation or equipment damage: 1) MINIMUM water pressure r equired at the water softener inlet is 20 psi (138 kPa).
1-3 Facts to Remember While Planning Y our Installation: 1) All installation procedures MUST conform to local and state plumbing codes. 2 ) If lawn sprinkling, a swimming pool, or geothermal heating/c.
Step 1 (a) Remove control valve by removing quick connect clamp and using a garden hose or bucket, to fi ll SOFTENER T ANK with water (this fi lling method prevents air entrapment tha t can cause loss of resin during initial regeneration proce- dure).
CAUTION T o reduce the risk associated with property damage due to plugged water lines: • P ay particular attention to correct orienta tion of control valve. W ater fl o w should match arrow on control valve. The Inlet and Outlet of other water trea tment equipment products will vary depending on the control valve brand used.
2-3 Step 5 Attach DRAIN LINE to DRAIN LINE FITTING. T o prevent back pressure from reducing fl ow ra te below minimum required for backwash, DRAIN LINE MUST be sized according to run length and relative height.
3-1 SECTION 3: REGENERA TION INSTRUCTIONS INSTRUCTIONS FOR USING REGENERA TION FREQUENCY SCHEDULES: (Time Clock Initiated Models Only) 1) Determine ADJUSTED HARDNESS b y adding three (3) times the iron content in parts per million (ppm) to the hardness in grains per gallon (gpg).
3-2 Model(s) 200 HARDNESS — gpg Persons In Family 5 1 01 52 02 53 03 54 04 55 05 56 06 57 07 58 08 59 0 1 111111111112222222 2 111112222223333334 3 111222233334444666 4 11222333444666666 1 2 5 11223.
3-3 HOW TO SET METER GENERA TION CONTROL: TYPICAL RESIDENTIAL APPLICA TION: T o program, just set the time, set the hardness and it automatically monitors system needs and regenerates only when necessary . T o set time of day , press red time set button and turn 24-hour gear until present time of day is opposite “time of day arrow.
4-1 SECTION 4: SERVICE INSTRUCTIONS Problem Cause Solution 1) Hard water , (unit NOT using salt; liquid level in brine tank NOT too high). A. Electrical ser vice to unit interrupted. A. Assure permanent electrical ser vice (check fuse, plug, pull chain or switch.
5-1 SECTION 5: SPECIFICA TION AND OPERA TING D A T A Timer Initiated Meter Initiated ITEM NWS100 NWS150 NWS200 NWS100M NWS150M NWS200M Nominal Media Volume, cu. ft. (cu mtr) 1.0 (0.03) 1.5 (0.05) 2.0 (0.06) 1.0 (0.03) 1.5 (0.05) 2.0 (0.06) Salt Dosage, lbs (kg): Factory Setting (1) Maximum Setting 6.
6-1 COMPONENTS P ARTS LIST TWO T ANK MODELS (NS & NSM SERIES) REF NO. DESCRIPTION NWS100 NWS100M NWS150 NWS150M NWS200 NWS200M 1 Control Valve, T ime Clock Initiation, with Cover , less Bypass Control Valve, Meter Initia tion, with Cover , less Bypass N100150-5W N12J150-5W N100240-5W N12N240-5W N100240-5W N12R240-5W 2 Adapter Assy .
CONTROL V AL VE -12 DA Y TIMER 6-3.
6-4 ONL Y THOSE P ARTS CIRCLED IN DRA WING AND/OR LISTED BELOW ARE STOCK ITEMS ALL OTHERS ARE SPECIAL ORDER, NON-RETURNABLE P AR TS LIST - 12 DA Y TIMER REF P AR T No. DESCRIPTION A 60353-13 Power Head Assy ., Complete, L/Cover , NS/NLS Series (Incl. Ref.
CONTROL V AL VE - METER INITIA TED 6-5.
6-6 ONL Y THOSE P ARTS CIRCLED IN DRA WING AND/OR LISTED BELOW ARE STOCK ITEMS ALL OTHERS ARE SPECIAL ORDER, NON-RETURNABLE P AR TS LIST - METER TIMER REF P AR T No. DESCRIPTION A 60354-13 Power Head Assy ., Complete, L/Cover , NWS Series (Incl. Ref. Items 2-40) B 14039X Program Wheel Assy .
7-1 SECTION 7: MAINTENANCE REPLENISHMENT OF SAL T SUPPL Y : The salt storage capacity of the brine tank is a pproximately 160 lbs. During each regeneration a specifi c amount of salt is consumed, thus requiring its periodic replenishment (the frequency is dependent on the regeneration schedule).
SECTION 8: LIMITED W ARRANTY For any warranty questions, please refer to the enclosed warranty card or call 1-800-222-7880 or mail your r equest to: 3M Purifi cation Inc . 400 Research Parkw ay Meriden, CT 06450 Aqua-Pure is a trademark of 3M Company used under license .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il 3M NWS200 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del 3M NWS200 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso 3M NWS200 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul 3M NWS200 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il 3M NWS200, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del 3M NWS200.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il 3M NWS200. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo 3M NWS200 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
