Manuale d’uso / di manutenzione del prodotto Axtreme 02984405 del fabbricante Alamo
Vai alla pagina of 106
Published 0 7 /06 (Rev 02-20-07) Part No. 0298 4405 ALAMO INDUSTRIAL 1502 E. W alnut Seguin, T exas 78155 830-379-1480 © 2006 Alamo Industrial ASSEMBL Y MANUAL (ST ANDARD INSTRUCTIONS) BOOM ARM MOWER.
.
.
TO THE OWNER/OPERA T OR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
© 200 6 Alamo Group Inc. Axtreme Boom General Assembly (02-06) (Rev 02-20-07) NOTES.
© 2006 Alamo Industrial Index -1 Axtreme Boom - Asy Man (07/06) INTRODUCTION ABOUT THIS MANUAL: The intent of this publications to provide the competent technician with the information necessary to assemble the Alamo Industrial Product. This will, in turn provide for complete customer satisfaction.
Axtreme Boom - Asy Man (07/06) © 2006 Alamo Industrial Index -2 Section Page Index.. ........................................................................................................................ Index-1 to Index 2 Section 1 Safety Instructions .
.
Section 1 - 1 © 2006Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 SAFETY SECTION Section 1 Axtreme Boom.
Section 1 - 2 © 2006 Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 Safety Section Read these assembly instructions through completely and understand them before proceeding with the assembly of the equipement. A safe and careful operator is the best operator .
Section 1 - 3 © 2006Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) PELIGRO! !LEA EL INSTRUCTIVO! READ , UNDERST AND , and FOLLOW the following Safety Messages.
Section 1 - 4 © 2006 Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 Many of the parts are heavy and require lifting assistance. Do not try to lift the heavy parts by yourself.
Section 1 - 5 © 2006Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 Before starting the mower make sure the area is clear and the floor has been swept. The mower blade can throw objects several hundred feet. Thrown objects could damge property or cause severe bodily injuries even death.
Section 1 - 6 © 2006 Alamo Group Inc. Axtreme Boom (Asy. Man.) 07/06 DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability t o operate the equipment safely.
© 2006 Alamo Industrial Section 2 - 1 Axtreme Boom - Asy Man (07/06) Axtreme Boom Model S pecifications Section 2.
© 2006 Alamo Industrial Section 2 - 2 Axtreme Boom - Asy Man (07/06) SPECIFICA TIONS - AXTREME BOOM READ THIS BEFORE BEGINNING ASSEMBL Y : The Axtreme Boom has electronic component s: . The electronic components can be damaged if care is not taken when performing repairs, testing and/or during assembly.
© 2006 Alamo Industrial Section 2 - 3 Axtreme Boom - Asy Man (07/06) 2 . Fif ty Inch (50") Cutting Head Specifications: Blade / Motor Rotation (Looking down from Top of Deck)............... Clockwise Blade Tip Speed..............................
© 2006 Alamo Industrial Section 2 - 4 Axtreme Boom - Asy Man (07/06) 5 . Control V alve: 5 S pool used with Rotary Heads w/ Door Valve Type................................................................................ Open Center 5 Spool Valve Control (Manual Standard).
© 2006 Alamo Industrial Section 2 - 5 Axtreme Boom - Asy Man (07/06) SPECIFICA TIONS - AXTREME BOOM 7 . V alve Sections Function: Mechanical Control Vale (See Figure 1) Spool Cylinder Function Pressu.
© 2006 Alamo Industrial Section 2 - 6 Axtreme Boom - Asy Man (07/06) 8 . Hose End Fitting T orque Specification: Hose End Type: 37 Degree Angle End Steel Hose End Fittings* Dash Nominal Cyl.
© 2006 Alamo Group Inc. Section 3 - 1 Axtreme Boom (Asy. Man) 07/06 Axtreme Boom T ractor Preperations Section 3 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model. The way the frame mounts to the tractor components can vary with tractor model.
© 2006 Alamo Group Inc. Section 3 - 2 Axtreme Boom (Asy. Man) 07/06 General Information: The tools you will need at the assembly site are as follows: 1. Welding equipment (including correct head gear, eye shields, and protective clothing.) 2. Impact wrench or socket and ratchet set.
© 2006 Alamo Group Inc. Section 3 - 3 Axtreme Boom (Asy. Man) 07/06 Disconnect the negative lead (ground) from the battery terminal to prevent any damage to the electrical system. WARNING! LEVELING TRACTOR: TRACTOR MUST be on level ground before assembly is begun.
© 2006 Alamo Group Inc. Section 3 - 4 Axtreme Boom (Asy. Man) 07/06 Replacement Oil Filter I ncluded in the packing box of this unit is a replacement filter element for filter assembly in the tank. This Mower unit's hydraulic components have been carefully cleaned and packaged at the factory to prevent contamination from entering the system.
© 2006 Alamo Group Inc. Section 3 - 5 Axtreme Boom (Asy. Man) 07/06 WARNING: Never operate the tractor with a loose wheel rim or disc. Always tighten nuts to the specified torque and at the recommended intervals. 2. Extend front wheels out so that it is 55" inches between the inside of the tires.
© 2006 Alamo Group Inc. Section 3 - 6 Axtreme Boom (Asy. Man) 07/06 Lay Out Component s in Display . It is helpful to lay out the component in as neat a display as possible. Lay out the Bolts according to size and length. Lay out the Nuts and washer by size.
© 2006 Alamo Group Inc. Section 3 - 7 Axtreme Boom (Asy. Man) 07/06 W ARNING DO NOT WELD On This Unit During or Af ter Installation: DO NOT WELD any components or items on this unit after the installation of the maverick Boom has begun. The Maverick Boom uses electronic modules and compo- nents that could be damaged by welding.
© 2006 Alamo Group Inc. Section 3 - 8 Axtreme Boom (Asy. Man) 07/06 NOTES.
© 2006 Alamo Group Inc. Section 4 - 1 Axtreme Boom (Asy. Man) 07/06 Axtreme Boom Battery , Exhaust & Fuel T ank Modification With Main Frame Inst allation Section 4 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model.
© 2006 Alamo Group Inc. Section 4 - 2 Axtreme Boom (Asy. Man) 07/06 that will relocate the battery tray farther to the rear. This is done so the Boom Swing will not hit battery when in the transport position. The RH Step Will need to be removed to allow access to relocate battery.
© 2006 Alamo Group Inc. Section 4 - 3 Axtreme Boom (Asy. Man) 07/06 Exhaust / Muffler Relocation Exhaust/Muffler Relocation: 1. Remove The Exhaust (If Required, See As- sembly Drawings sent with unit) . . The Exhaust relocation kit will include a new mounting bracket, Bolting hardware, replacement exhaust pipe from turbo to muffler.
© 2006 Alamo Group Inc. Section 4 - 4 Axtreme Boom (Asy. Man) 07/06 Fuel T ank Replacement over head hoist to support and lift the wheel and tire assembly. The tractors factory fuel tank is mounted behind the RH rear tire and wheel (See Figure 9). 2.
© 2006 Alamo Group Inc. Section 4 - 5 Axtreme Boom (Asy. Man) 07/06 5. Install the new mount brackets to the tractor frame. (If Required, See Assembly Drawings sent with unit) The tank mounting brackets will bolt to the tractor the same as the factory brackets that were removed.
© 2006 Alamo Group Inc. Section 4 - 6 Axtreme Boom (Asy. Man) 07/06 Frame Inst allation Under Mount Frame Asy (24 & 30 ft are the same except for the LH weight) 30 ft model only Swing Cylinders S.
© 2006 Alamo Group Inc. Section 4 - 7 Axtreme Boom (Asy. Man) 07/06 Frame Inst allation: 1. Frame Components. The frame will include the rear axle mounts, a LH & RH Frame rail. Two front frame mounts, a LH & RH. One center frame weldment. (See Figure 17, 18, 19, 20 & 21) 2.
© 2006 Alamo Group Inc. Section 4 - 8 Axtreme Boom (Asy. Man) 07/06 Frame Inst allation 3. Install Rear Frame Mount Rails. Rear frame rails consist of a LH & RH. We have started with the Left Hand Rail. The three point lift stabilizer brackets will need to be unbolted on both sides.
© 2006 Alamo Group Inc. Section 4 - 9 Axtreme Boom (Asy. Man) 07/06 5. Install Center Frame Weldment. The Center Frame Weldment has a front and a back side (LH & RH side). The Center frame must be installed with the two openings (See Figure 26) toward the front of the tractor.
© 2006 Alamo Group Inc. Section 4 - 10 Axtreme Boom (Asy. Man) 07/06 Frame Inst allation Boom Rest Weldment (f/24 ft. boom) & (f/ 30 ft. boom) Figure 29 Figure 31 Figure 30 7. Install LH Axle Strap. The Axle Strap bolts down over the top of the Axle (LH Side) and bolts run through the Rear Frame rails.
© 2006 Alamo Group Inc. Section 4 - 11 Axtreme Boom (Asy. Man) 07/06 Counter Weight Inst allation : 1. Counter Weight (CWT) Installation. The Counter weight (See Figure 1 ) mounts on the LH side Under Frame Weldment. Its is retained with three pins, the long pin on top, the short pin at the rear and a short pin at the front.
© 2006 Alamo Group Inc. Section 4 - 12 Axtreme Boom (Asy. Man) 07/06 Figure 34 Figure 33 Frame Inst allation T urret Assembly Installation : 1. Turret Assembly. Theturret assembly is shipped assembled with the hydraulic swing cyl- inders, hoses, pivot bearing assembly, boom mount weldment and mounting pins installed (See Figure 35 & 36).
© 2006 Alamo Group Inc. Section 4 - 13 Axtreme Boom (Asy. Man) 07/06 Figure 37 Figure 38 3. Turret Assembly Installation. Theturret assembly mounts on the RH side onto the center section under frame (See Figure 36 & 37) . Using a hoist (or other lifting device) lower the turret assembly until it is level with the underframe.
© 2006 Alamo Group Inc. Section 4 - 14 Axtreme Boom (Asy. Man) 07/06 Adjust Boom Swing Stop CAUTION ! You MUST READ and UNDERSTAND this section as it is critcal BEFORE attempting to put boom rest position the first time. FAILURE TO PERFORM THIS ADJUSTMENT could cause damage to the cab of the tractor.
© 2006 Alamo Group Inc. Section 4 - 15 Axtreme Boom (Asy. Man) 07/06 Adjust Boom Swing Stop Swing Stop Lug Built onto the Turret Cylinder Link Weldment T urret Assembly as seen from the bottom Turret.
© 2006 Alamo Group Inc. Section 4 - 16 Axtreme Boom (Asy. Man) 07/06 NOTES.
© 2006 Alamo Group Inc. Section 5 - 1 Axtreme Boom (Asy. Man.) 07/06 Axtreme Boom Wheel W eight Inst allation Section 5 This section show the secondary weight that can be added to the LH rear wheel. NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model.
© 2006 Alamo Group Inc. Section 5 - 2 Axtreme Boom (Asy. Man.) 07/06 Rear Wheel Counter Weight Item Part No. Qt y Description 1 02979603 3 Hex Head Bolt, 7/8" NC X 16" 2 02971569 3 Wheel Weight Washer, Special 3 02970758 1 Wheel Weight Casting, 1400 lbs.
© 2006 Alamo Group Inc. Section 5 - 3 Axtreme Boom (Asy. Man.) 07/06 Rear Wheel Counter Weight Inst alling Wheel Weight 1. This Wheel Weight is 1400 lbs. Always use caution when working with it. 2. Locate the three Holes in LH Rear Wheel. Make sure these holes are 15/16" dia.
© 2006 Alamo Group Inc. Section 5 - 4 Axtreme Boom (Asy. Man.) 07/06 NOTES.
© 2006 Alamo Industrial Section 6 - 1 Axtreme Boom (Asy Man) 07/06 Axtreme Boom Section 6 T ypical Pump - Driveline - Hyd Assembly instructions NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model. The way the frame mounts to the tractor compo- nents can vary with tractor model.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 2 Pump - Driveline - Hose Removal Pump - Driveline - Hose Information: This Section covers the Pump and Driveline Components. Some precautions must be followed during the assembly Process before unit is ever started for the first time.
© 2006 Alamo Industrial Section 6 - 3 Axtreme Boom (Asy Man) 07/06 Pump - Driveline - Hose Removal Clamp Yoke & Tube End Tractor Engine Pulley Pulley Adpater Use Bolts & Washers (4 ea.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 4 Figure 5 Tube End of Driveshaft Splined Clamp Yoke Typical Pump Mount Plate Shown Figure 6 Bar to Hold Drive Shaft Driveshaft, Spline Clamp Yoke End 4. Driveline timeing means the universal joints are both the same position when driveline half is slid together.
© 2006 Alamo Industrial Section 6 - 5 Axtreme Boom (Asy Man) 07/06 Figure 1 1 Gap ? Check, this must have a gap between Pump & drivesahft Figure 10 Figure 9 Pump Assembly Splined Clamp Yoke 1/16" to 1/8" Gap between Pump & Yoke (must) Pump - Driveline - Hose Installation 9.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 6 Figure 13 Figure 14 Return Hose & Return Filter Pressure Hose To Motor Pressure Hose to Cyl Valve Tank Suction Hose Control Valve Figure 12 Pump Retaining Bolts (2) 12. Tightening Pump Mounting Bolts.
© 2006 Alamo Industrial Section 6 - 7 Axtreme Boom (Asy Man) 07/06 Figure 15 Motor Control V alve Block Pump - Driveline - Hose Installation The pump / motor control valve block, this bolts to the right hand side of the pump (See Figure 13, 14, 15 & 16).
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 8 Pump - Driveline - Hose Installation Cylinder Diverter V alve Block The Cylinder Diverter Valve Block is used to control the hydraulic head swivel option if used.
© 2006 Alamo Industrial Section 6 - 9 Axtreme Boom (Asy Man) 07/06 Pump - Driveline - Hose Installation Return From Cyl Control Valve Return to Tank Return Filter Return Oil Cooler with Fan Figure 21.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 10 Hyd Schematic - Mechanical Operated (S t d) Figure 22 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Filte.
© 2006 Alamo Industrial Section 6 - 11 Axtreme Boom (Asy Man) 07/06 Hyd Schematic - Electrically Controlled (Opt) Figure 23 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Fil.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 6 - 12 NOTES.
© 2006 Alamo Group Inc. Section 7 - 1 Axtreme Boom (Asy. Man) 07/06 Axtreme Boom Boom & Head Inst allation W ith Hyd Connections Section 7 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model. The way the frame mounts to the tractor compo- nents can vary with tractor model.
© 2006 Alamo Group Inc. Section 7 - 2 Axtreme Boom (Asy. Man) 07/06 Boom / Head Inst allation Figure 1 Swing Cyl. Hose with Green / White Tie Swing Cyl. Hose with Green Tie Rear of Tractor Boom Installation / Boom Hoses: 1. Turret Assembly, The turret assembly has the cylinders connected and the hoses are connected to the cylinders.
© 2006 Alamo Group Inc. Section 7 - 3 Axtreme Boom (Asy. Man) 07/06 6. Connect lower end of Lift Cylinder. The Base end (lower end) of lift cylinder will mount into the turret under the boom mount.
© 2006 Alamo Group Inc. Section 7 - 4 Axtreme Boom (Asy. Man) 07/06 Figure 4 Figure 5 Figure 6 Figure 7 50 Inch Head w/o Swivel Hitch Mount 50 Inch Head w/o Swivel Hitch Mount 60 Inch Head with Swive.
© 2006 Alamo Group Inc. Section 7 - 5 Axtreme Boom (Asy. Man) 07/06 Figure 8 Head Swivel Cyl. # 4 Hose (Green / White Tie) Head Swivel Cyl. # 4 Hose (Green Tie) Door Cyl. # 4 Hose (Yellow Tie) Motor Pressure # 16 Hose (Red Tie) Motor Tank Return #16 Hose (Orange Tie) Motor Case Drain #12 Hose (Blue Tie) Door Cyl.
© 2006 Alamo Group Inc. Section 7 - 6 Axtreme Boom (Asy. Man) 07/06 Boom / Head Inst allation Figure 1 1 Figure 12 Figure 13 Sleeving Material for Hoses Hose Support Bracket Figure 14 Red Tie Blue Tie Orange Tie 12.
© 2006 Alamo Group Inc. Section 7 - 7 Axtreme Boom (Asy. Man) 07/06 Boom Cylinder Circuit Hoses: Electrical Joystick Controlled Valve (Option) Color Tie (Code) Hose Size Port Diverter Hyd.
© 2006 Alamo Group Inc. Section 7 - 8 Axtreme Boom (Asy. Man) 07/06 Hydraulic Hose Connections VS . 125/F C2 C3 SAE 4 P1 P2 Valve "B" Port to Diverter valve P1 Port (Green w/ White Tie) Val.
© 2006 Alamo Group Inc. Section 7 - 9 Axtreme Boom (Asy. Man) 07/06 Hydraulic Hose Connections 3 4 Door (Y ellow) Tilt (Red) Tilt (Red / White) Dipper (Blue) Dipper (Blue / White) Lift (Orange) Lift .
© 2006 Alamo Group Inc. Section 7 - 10 Axtreme Boom (Asy. Man) 07/06 Hyd Schematic - Mechanical Operated (S t d) Figure 20 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Filt.
© 2006 Alamo Group Inc. Section 7 - 11 Axtreme Boom (Asy. Man) 07/06 Hyd Schematic - Electrically Controlled (Opt) Figure 21 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Fi.
© 2006 Alamo Group Inc. Section 7 - 12 Axtreme Boom (Asy. Man) 07/06 NOTES.
© 2006 Alamo Industrial Section 8 - 1 Axtreme Boom (Asy Man) 07/06 Axtreme Boom Section 8 Remote V alve Cable Inst allation This Control valve is the Standard 5 Spool that is remote cable controlled, with the 5 Th. Spool operating the Door or the Swivel Head Mount Option through a diverter valve.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 2 Wire Harness : (Standard Mechanical Valve) 1. Starter Safety Switch Schematic, Mechanical Cable Operated Valve Type, NOT correct for Optional Joystick (Electronic) Controls.
© 2006 Alamo Industrial Section 8 - 3 Axtreme Boom (Asy Man) 07/06 Wire Harness - Cable Controled V alve Figure 1.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 4 Mechanical Remote Cable Controled V alve (S tandard) Figure 1 Door (Y ellow / White) Tilt (Red / White) Tilt (Red) Dipper (Blue / Whi.
© 2006 Alamo Industrial Section 8 - 5 Axtreme Boom (Asy Man) 07/06 V alve Remote Cable Controls Figure 2 11. Cable Mounting Bracket 8. Clevis Retaining Bolt 7. Screw On Cable Clevis Valve Asy 9. Clevis Retaining Nut 6. Cable To Clevis Locking Nut 5. Threaded Cable End 3 & 4 Cable Housing Locking Nuts & Adjusting Nuts 2.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 6 V alve Remote Cable Controls 6. Cable Clevis Installation. Screw the cable clevis (item 7) onto the threaded cable (item 5) until the threads are fully engaged into the clevis. If the locking nut (item 6) needs to be run further onto cable, this is OK.
© 2006 Alamo Industrial Section 8 - 7 Axtreme Boom (Asy Man) 07/06 10. Connect Cable to Control Handle. Install the cable locking nut onto the threaded cable (See Figure 7), screw the nut on leaving enough threads to fully screw the control handle to the cable.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 8 Figure 1 1 V alve Remote Cable Controls 13. The Arm Rest is bolted to the Control Handles. This has some options as to where it is bolted and can be bent to adjust to individual preference.
© 2006 Alamo Industrial Section 8 - 9 Axtreme Boom (Asy Man) 07/06 Start Off Ign Acc Acc T ractor Ignition Switch Push/ Pull Switch T ractor S tarter Brown Wire Brown Wire Y ellow or Orange Wire 10Am.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 10 Battery Brown Wire of Harness Cut Tractor Starter Wire to Starter Sole- noid and reroute through Joystick Harness Brown wires.
© 2006 Alamo Industrial Section 8 - 11 Axtreme Boom (Asy Man) 07/06 Hyd Schematic - Mechanical Operated (S t d) Figure 18 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Filte.
Axtreme Boom (Asy Man) 07/06 © 2006 Alamo Industrial Section 8- 12 Door (Y ellow / White) Tilt (Red / White) Tilt (Red) Dipper (Blue) Lift (Orange / White) Lift (Orange) Swing (Green / White) Swing (.
© 2006 Alamo Industrial Section 9 - 1 Axtreme Boom (Asy Man) 07/06 Axtreme Boom Optional Electric / Hydraulic Joystick Cylinder Control V alve Inst allation Section 9 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model.
© 2006 Alamo Industrial Section 9 - 2 Axtreme Boom (Asy Man) 07/06 Joystick Mounting Joystick Optional : The joystick is an option and allows the mower & boom to be operated with electronic control. The joystick will be mounted in different ways depending on the type tractor you have.
© 2006 Alamo Industrial Section 9 - 3 Axtreme Boom (Asy Man) 07/06 Joystick Mounting Joystick Resister Wiring Harness (Used with Joystick Option Only) FIGURE 3.
© 2006 Alamo Industrial Section 9 - 4 Axtreme Boom (Asy Man) 07/06 Wiring Harness used with Joystick V alve Controls Only (Note: Wires are marked with function identification) Joystick Mounting FIGUR.
© 2006 Alamo Industrial Section 9 - 5 Axtreme Boom (Asy Man) 07/06 Joystick Mounting through. If there is no hole one will need to be cut with a hole saw. Check the under side of the cab floor to make certain you do not hit a brace or any other object under the floor (See Figure 5) .
© 2006 Alamo Industrial Section 9 - 6 Axtreme Boom (Asy Man) 07/06 Joystick Mounting Item Qty Description 6. 2 Flatwasher 7. 2 Lockwasher 8. 2 Bolt 9.
© 2006 Alamo Industrial Section 9 - 7 Axtreme Boom (Asy Man) 07/06 Joystick Mounting 4. Install Joystick Console Controler. Set the Joystick Controller down on top of the mounting bracket and insert the two mounting bolts (with flat washer and lockwashers) form the bottom side of the console.
© 2006 Alamo Industrial Section 9 - 8 Axtreme Boom (Asy Man) 07/06 Joystick Mounting Cut Tractor Starter Wire to Starter Sole- noid and reroute through Joystick Harness Brown wires. Shown here is typical Ignition connection, Your Ignition may vary but the function will not.
© 2006 Alamo Industrial Section 9 - 9 Axtreme Boom (Asy Man) 07/06 Inst alling Wire Harness T o V alve: 1. Wire Harness From Cab to Front. The wire harness runs out the bottom of the Cab on the right hand side. Run harness along under RH cab of Tractor to the control valve (See Figure 21).
© 2006 Alamo Industrial Section 9 - 10 Axtreme Boom (Asy Man) 07/06 5. Terminal Connections. The Valve is mounted on the left hand side of the hydraulic tank.
© 2006 Alamo Industrial Section 9 - 11 Axtreme Boom (Asy Man) 07/06 Hyd Schematic - Electrically Controlled (Opt) Figure 26 Swing Cyl's Lift Cyl Dipper Cyl T ilt Cyl Pump Hyd T ank Return to Fil.
© 2006 Alamo Industrial Section 9 - 12 Axtreme Boom (Asy Man) 07/06 Hyd Hose Codes at Control Valve & Head Swivel Divertor Valve Option Hose Bands Mark Color Codes: Hose fittings are marked with Color Coded Plastic Band. Some Bands are solid Color, some are Colored with Stripe.
© 2006 Alamo Group Inc. Section 10 - 1 Axtreme Boom ( Asy. Man.) 07/06 Axtreme Boom Fill Hydraulic T ank & S t art Up Instructions Section 10 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model.
© 2006 Alamo Group Inc. Section 10 - 2 Axtreme Boom ( Asy. Man.) 07/06 Fill Hydraulic T ank Fill Hydraulic T ank with Oil: 1 . DO NOT START TRACTOR until you have filled Hydraulic Oil Tank to a level as shown in Sight Glass gauge and fill the Suction Hose to Pump with Oil.
© 2006 Alamo Group Inc. Section 10 - 3 Axtreme Boom ( Asy. Man.) 07/06 Fill Hydraulic T ank Fill Hydraulic T ank with Oil: 5. Fill Tank . Fill the Hydraulic Tank (See Figure 4) Fill tank till the Oil is visible in the sight Gauge (See Figure 5 & 7).
© 2006 Alamo Group Inc. Section 10 - 4 Axtreme Boom ( Asy. Man.) 07/06 NOTES.
© 2006 Alamo Group Inc. Section11 - 1 Axtreme Boom (Asy. Manl) 07/06 Axtreme Boom PRE-DELIVER Y INSPECTION CHECKLIST Section 1 1 NOTE: This shows a basic mount for the frame installation and may not be the same for your tractor model. The way the frame mounts to the tractor components can vary with tractor model.
© 2006 Alamo Group Inc. Section 11 - 2 Axtreme Boom (Asy. Manl) 07/06 PRE-DELIVER Y INSPECTION CHECKLIST Pre-Operation Inspection: Check the following items before operating the unit to assure that they are properly assembled. (See previous pages for component location) Saf tey Equipment: ----- Operators Manual is with Unit.
© 2006 Alamo Group Inc. Section11 - 3 Axtreme Boom (Asy. Manl) 07/06 PRE-DELIVER Y INSPECTION CHECKLIST Pre-Operation Inspection: Check the following items before operating the unit to assure that they are properly assembled. Flail Mower Head: ___ Skid Shoe Bolts are torqued to 120 ft-lbs.
© 2006 Alamo Group Inc. Section 11 - 4 Axtreme Boom (Asy. Manl) 07/06 NOTES.
.
Axtreme Boom (Asy. Man) 07/06 (STANDRAD ASSEMBLY INSTRUCTIONS) (Rev 02-20-07) © 2006 Alamo Group Inc. Axtreme Boom Assembly Manual P/N 0298 4405.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Alamo Axtreme 02984405 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Alamo Axtreme 02984405 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Alamo Axtreme 02984405 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Alamo Axtreme 02984405 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Alamo Axtreme 02984405, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Alamo Axtreme 02984405.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Alamo Axtreme 02984405. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Alamo Axtreme 02984405 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.