Manuale d’uso / di manutenzione del prodotto 5232IM del fabbricante Dynex
Vai alla pagina of 19
CD-WRITER 5232IM CD-ReWritable Drive User’s Manual.
DANGER INVISIBLE LASER RADIATION WHEN O PEN AVOID DIRECT EXPOSURE TO BEAM VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATIO N DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYO NS.
FCC Compliance Statement This device complies with Part 15 of the FCC Ru les. Operation is subject to the following two condit ions: 1. this device ma y not cause harmful i nterference, and 2. this device must accept any interferen ce received, including interference that may cause undesired operat ion.
Table of Contents INTRODUCTION 1 S YSTEM R EQUIREMENTS 2 P ACKAGE C ONTENTS 2 INSTALLATION 3 H OST I NTERFACE C ONNECTIONS 3 H ARDWARE I NSTALLATION 4 D RIVER I NSTALLATION 6 Windows Environment 6 S O.
CD-WRITER 5232IM 1 INTRODUCTION CD-WRITER 5232IM is a half-height CD-ReWritable drive of standard IDE interface. It supports maximu m 52X speed writing ability on CD-R discs, 32X speed on CD-RW discs and 52X speed reading performance.
CD-WRITER 5232IM 2 System Requirements For IBM compatible PCs, the system requirements recommended are as follows: ♦ PC sufficient to run Windows 98/ME/2000/XP ♦ Pentium II 350MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
CD-WRITER 5232IM 3 INSTALLATION Host Interface Connections Most current mainboard models have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four dev ices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive.
CD-WRITER 5232IM 4 You may consider one of the two ways recommended below to connect your drive. ♦ To get the most stable performance for the CD-RW drive to write: Primary IDE Master: Hard Disk Prim.
CD-WRITER 5232IM 5 The red-edge of the IDE Cable must be connected to Pin 1 on the CD- ReWritable drive. 5. If you have a sound card that can be connected to this CD- ReWritable drive, you can connect the drive (as Audio-out) and the sound card (as Audio-in) with a 4- pin audio cable.
CD-WRITER 5232IM 6 Driver Installation Windows Environment CD-WRITER 5232IM is a PnP device, and Windows 98/ME/2000/XP can automatically detect the drive and load the appropriate driver. If Windows cannot detect the driv e, you can operate manually: 1.
CD-WRITER 5232IM 7 CONNECTION & OPERATION Front Panel 12 4 3 1. LED Indicator Flashes “green” while verifying or reading a disc/ writing a CD- R/CD-RW disc. 2. Disc Tray This is the tray for the disc. Pl ace the disc in the tray, then press the Close/Eject button or lightly push the tray to close it.
CD-WRITER 5232IM 8 NOTE: The front panel is subject to change wi thout notice. Rear View 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable.
CD-WRITER 5232IM 9 TECHNICAL DATA Performance Transfer rate Read : CD-ROM/CD-R: 7800kb/s (up to 52X) CD-RW: 6000kb/s (up to 40X) Write: CD-R 7800kb/s (up to 52X) CD-RW 4800kb/s (up to 32X) Access time.
CD-WRITER 5232IM 10 Form factor 5.25" Half Height Disc loading Tray (motorised) Audio output level Line out = 0.6 ± 10%Vrms Headphone out = 0.6± 10%Vrms Power 5 VDC & 12VDC Dimensions Height 41.8 ± 0.2 mm Width 148.6 ± 0.3 mm Depth 177.0 ± 0.
CD-WRITER 5232IM 11 Environment Temperature Operating 5°C to 45°C Non-operating -20°C to 60°C Humidity Operating 8% ~ 80%RH Non-operating 5% ~ 95%RH.
CD-WRITER 5232IM 12 TROUBLESHOOTING To help you get more familiar with CD-WRITER 5232IM, the following FAQ lists some common problems you might encounter. Please read it for reference before you request RM A support from your dealer. Q1. CD-WRITER 5232IM cannot be recognized.
CD-WRITER 5232IM 13 (1) Please check if the audio cable is connected to the audio connector properly. (2) Check both rear side of the CD-RW drive and sound card on M/B (If Audio chipset is on board). If they are well connected, check if the sound card is working.
CD-WRITER 5232IM 14 (4) Increase main memory capacity. (5) Select other burning software. (6) De-fragment the hard disk. (7) Keep the source & destination discs clean. (no scratches, fingerprints or contamination.) (8) Copy data as image file to hard drive to avoid buffer underrun.
3100552360 Version 1.0 March 2004.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dynex 5232IM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dynex 5232IM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dynex 5232IM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dynex 5232IM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dynex 5232IM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dynex 5232IM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dynex 5232IM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dynex 5232IM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
