Manuale d’uso / di manutenzione del prodotto XDVD1002CM del fabbricante Dual
Vai alla pagina of 20
INSTALLATION/OWNER'S MANUAL XDVD1002CM.
D V D O p e r a t i o n . . . . . . ...................................... C D O p e r a t i o n ............................................. M P 3 O p e r a t i o n ........................................... D i v X O p e r a t i o n . . . . ......
3 XDVD1002CM PREPARATION Before You Begin Cautions To prevent damage or injury: 1. Make sure to ground the unit securely to the vehicle chassis ground. 2. Do not remove the top cover of the unit. 3. Do not install the unit in a spot exposed to excessive heat or the possibility of water splashing.
4 5 XDVD1002CM PREPARATION Contents Main Unit Remote Control Recommended Tools and Equipment • Upholstery hook tool (for removal of panels, if necessary) • #1 and #2 Phillips screwdrivers • Utility knife, razor knife, or shears • Misc.
4 5 XDVD1002CM INSTALLATION Wiring Diagram - Main Unit Yellow Black Red Brown Brown/Black Green Aux 2 Input (Red Jacket) A/V Output (Black Jacket) Connect to battery circuit or constant 12 volt source.
XDVD1002CM INSTALLATION Mounting 6 1. Test fit the mounting bracket and unit on the ceiling of the vehicle, verify- ing that it is not going to interfere with the safe operation of the vehicle and is physically safe for the driver and passengers. 2. Once the mounting location is determined, carefully mark the location with masking tape.
XDVD1002CM OPERATION Control Locations - Main Unit 7 9 10 11 2 3 6 4 5 Power Source Select Chapter/Track Down Dome Light Switch Screen Release Aux1 Inputs 1 2 3 4 Rear IR Sensor Motorized Disc Slot Fr.
XDVD1002CM OPERATION Control Locations - Remote 8 9 Power Return Fast Reverse Enter Chapter/Track Down Root Menu Setup Menu Step Subtitle Dimmer Angle 1 Shuffle Goto Video/Source Repeat LCD Screen Men.
XDVD1002CM OPERATION General Operation To turn on the unit, press the power button on the main unit or on the remote. Press again to turn the unit off.
Press SOURCE on the main unit to select between the following sources: AUX1 > AUX2 > DVD. Press SOURCE on the remote to select between AUX1 > AUX2 > DVD. Adjust volume using VOLUME / on the remote (0-16). Press MUTE on the remote to silence the audio.
XDVD1002CM OPERATION General Operation - Setup Menu 10 11 In the AUDIO SETUP menu, the following menus are availble: Select SPDIF from the AUDIO SETUP menu. Press to make selection. Press or to adjust (ON/OFF). Select OP MODE from the AUDIO SETUP menu.
XDVD1002CM OPERATION DVD Operation 12 13 Press SOURCE on the remote or the main unit to select DVD mode. Press EJECT on the remote control or on the main unit to open the motorized disc slot, insert disc. Press EJECT on the remote control or on the main unit to eject the disc.
XDVD1002CM OPERATION DVD Operation 12 13 Press A-B on the remote for more than 2 seconds to set point “A”. Press A-B for more than 2 seconds to set point “B”. The points between “A” and “B” will continually repeat. Press A-B to cancel repeat A-B.
14 15 XDVD1002CM OPERATION CD Operation Press SOURCE on the remote or the main unit to select DVD mode. Press EJECT on the remote control or on the main unit to open the motorized disc slot, insert disc. Press EJECT on the remote control or on the main unit to eject the disc.
14 15 XDVD1002CM OPERATION Additional MP3 Operation When an MP3 encoded disc is first inserted, SMART NAVI will show on screen. The disc will automatically begin playback . NOTE: It may take a few seconds for the unit to read disc. Disc playback must be stopped by pressing on the remote.
16 17 XDVD1002CM OPERATION DivX ® Operation When a DivX encoded disc is first inserted, playback will begin with the first file auto- matically, To access the SMART NAVI menu screen, stop playback by pressing on the remote . Disc playback must be stopped by pressing on the remote.
16 17 XDVD1002CM WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
18 19 XDVD1002CM OPERATION Troubleshooting Copyright Notes This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
18 19 XDVD1002CM OPERATION Specifications Signal-to-noise: >92dB Dynamic range: >85dB Frequency response: 20Hz-20kHz Panel size: 10.2 ” Diagonal measurement Format: Widescreen 16:9 View area: 8.
Dual Electronics Corp. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-382-5476 www.dualav.com ©2005 Dual Electronics Corp. All rights reserved.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dual XDVD1002CM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dual XDVD1002CM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dual XDVD1002CM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dual XDVD1002CM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dual XDVD1002CM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dual XDVD1002CM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dual XDVD1002CM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dual XDVD1002CM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
