Manuale d’uso / di manutenzione del prodotto 9310 del fabbricante DKS Enterprises
Vai alla pagina of 55
Model 9310 Vehicular Slide Gate Operator Owner’s Manual DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com P/N 9310-065 Rev E 5/07 Copyright 2003 DoorKing, Inc. All rights reserved.
Page 2 9310-065-E-5-07.
Use this manual with the following models only . All 9310 models with circui t board 4403-010. IMPORTANT! The 4403 circuit board used in th e model 9310 IS NOT interchangeable with the 440 2 circuit board used in the earlier model 9300 operators.
Mount operator to pad usin g 3/8 or 1/ 2 s leev e anchors. See page 18-19. 1 2 Attach chain. Adj ust chai n t o all ow approxi m at ely 1-inch of sag per 10-feet of gate widt h. Be sure to remov e th e pin f rom the breather plug. See page 20-21. 3 Connect supply volta ge as desc ribed in section 2.
9410 9410 EXIT LOOP REVERSE LOOP ON 12 3 1 DIRECTION 2 TIMER 1 Open Cycle Photocell 2 Close Cy cle Photocell 3 Open Cycle Contact Se nsor 4 Close Cy cle Contact Se nsor 5 Common 6 Common Secondary Ent.
Glossary GATE: A moving barrier such as a s winging, sliding, raisi ng, lo wering, or the like, barrier, that is a sta nd-alone passage barrier or is that portion of a wall or fence system that controls entrance and/or egress by persons or vehicles and completes the perimeter of a defined are a.
Entrapment Protection Protection Against Entrapment TYPE A: Inherent entrapment protection system. TYPE B1: Provision for connection of, or supplied with, a non-contact sensor (photoelectric sensor or the equivalent). Whe n used as the PRIMARY device, must be monitored.
Important Notices Vehicular gate ope rator products p rovide convenience and securit y. However, gate operators must use high levels of force to move gates and most people underestimate the power of these systems and do not realize the pote ntial hazards associated with an incorrectly desi gned or installed system.
Important Safety Instructions WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate controls. Keep the remote cont rol away from children. 3. Always keep peopl e and objects away from g ate.
Instructions regarding intended installation: Install the gate operator only if: 1. The operator is app ropriate for the cons tru ction of the gate and the usage class of the gate. 2. All openings of a horizontal slide gate ar e guard ed or screened from the bottom of the gate to a minimum of 4 feet (1.
For gate operators utili zing contact sensors: 1. One or more contact sensors shall be located where the risk of entrapment or obstruction exist, such as at the leading edge, trailing edge, and post mounted both inside and outside of a veh i cula r horizontal slide gate.
Slide Gate Requirements Gate Roadway Pedestrian Access Fence Vehicula r Ga t e Sidewalk Operator Fence All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minim um of four (4) feet (1.22 m) above the ground to prevent a 2 1/4 inch (57.
Slide Gate Protection Fence Operator Pedestrian Access Fence Sidewalk Reverse Loop Reverse (Open) Loop Open Loop (Optional) 1 1 1 2 3 4 Loops to he lp mi ni mi z e t h e pot e nt ia l of th e ga t e to close w hen a ve hicle i s pres e nt. Num ber and placement of loops is depend ent on the application.
Table of Contents Section 1 – Installation 1.1 Specifications ............................................................................................................. ..............................17 1.2 Concrete Pad ...........................
Section 5 – Maintena nce and Troubleshooting 5.1 Maintenance Schedule ....................................................................................................... ...................... 45 5.2 Operator Diagnostics ........................
Page 16 9310-065-E-5-07.
SECTION 1 - INST ALLA TION Prior to beginning the installation of the slide gate operator, we suggest that you become familiar wit h the instructions, illustration s, and wiring guide-lines in this manu al. This will help insure that your installation is performed in an efficient and professio nal manner.
1.2 Concrete Pad The model 9310 vehicular gate operato r is desi gned to be mounted on a concrete pad. 1. Construct a form for the mounting pad ac cordi ng to the specifications shown below. No te that the pad for the 1 H P operator extends an a dditional 6 inches to the right to accommodate the larger cov er .
1.3 Operator Installation Position the operator on the pad so that there is a minimum clearance of one (1) in ch between the back of the operator housing and the g ate.
1.4 Chain Installation 1. Secu re the chain brackets to each e nd of the gate so that the brackets are level with the top chain cutouts in the operator housing . Brackets should be attached to the insi de of the frame so that the chain bolts, when attached, do not protrude beyond the frame of the gate.
1.5 Front Mount Installation 4 8 GROUND LEVEL CONCRETE PAD REMOVE BREATHER PLUG PIN 9310-065-E-5-07 Page 21.
1.6 Rear Mount 4 8 GROUND LEVEL CONCRETE PAD REMOVE BREATHER PLUG PIN Gate Brackets Idler Assembly P/N 2600-818 Page 22 9310-065-E-5-07.
1.7 Warning Sign Installation This DoorKing slide gate operator i s shipped with two warning signs. The purpose of the warning signs is to alert uninf ormed persons, a nd to remind persons familiar with the system, that a potential hazard may exist so that appropriate action can be ta ken to avoid the hazard or to redu ce exposure to the hazard.
Page 24 9310-065-E-5-07.
SECTION 2 – WIRING Before attempting to connect any wiring to the oper ator, be sure that the circuit brea ker in the electrical panel is in the OFF po sition. A separate po wer disconnect must be installed at the operator location. Perm anent wiring must be installed to the op erator as required by lo cal electrical codes.
2.1 High Voltage Connections Use Table 1 to determine high voltage wire si ze re quirements. T he distance shown in the ch art is measured in feet from the operator to the power so urce. If power wiring is grea ter than the maximum distance shown, it is reco mmended that a service feeder be in stalled.
2.2 Control Wiring Controls must be far en ough from the gate so that th e user is prevented from co ming in contact with the gate while operating the c ontrols. Outdoor or easily acc essible controls should have a security feature to prev ent unauthor ized use.
2.3 Loop Detectors Loops and loop detectors must be i nstalled with this gate opera tor to prevent the gate from accidentally closing on vehicles th at may be in the path of the gate . Detail A Detail A TB 1 From inside Reverse loop From outside Reverse loop Reverse Reverse Exit DOORKING, INC.
2.4 Auxiliary Device Wiring 123456789 1 0 1 1 1 2 1 3 1 4 15 16 17 18 4403-010 Circuit Board Secondary Entrapment Prote ction Input s DOORKING, I NC., INGLEWOOD , CA 90301 Title: Date: Rev.
2.5 Primary – Secondary (Bi-parting) Gate Wiring The interface wiring between the two operator s requir es six (6) wi res (18 AWG minimum) for control and secondary entrapment protection d evice connecti on. Each operator must be conne cted to it's own power source as de scribed in section 2.
2.6 Terminal Identification and Description 2.6.1 M ain Terminal (P1) 1. 24 VOLT COMMON Same as terminal 13. 2. OPEN / RADIO RELAY Functions same as terminal 4. 3. 24 VOLT RADIO POWER 4. FULL OPEN / CLOSE INPUT When gate is closed, input w ill open gate to full position.
2.6.2 Secondary Device Terminal (P3) External entrapment prevention devices are connected here. 1. OPEN PHOTO-BEAM This input is only active when the gate is in the opening cycle. An open photo-beam input during the opening cycle will cause the gate to stop.
SECTION 3 - ADJUSTMENTS The switch settings and adjustments in this chapte r should be made after your installation and wiri ng to the operator(s) is comp lete. Whenever any of the programming switche s on the circuit board are changed, power must be shut-off, and then turned back on for the new setting to take effect.
3.2 Switch Settings The two DIP-switches located on th e circuit board are used to p rogram the operator to operate i n various modes and to turn on or off various ope rating features. Whenever a switch setting is changed, power to the o perator must b e turned OFF and then turned b ack on for the new setting to take affect.
3.2.1 Programming Switch Description and Function 8-DIP (Top) S witch Sw it ch 1 : Set so that the operator cycles open u pon initial power up and open command. If the operator cycles close, turn powe r o ff and change the setting on this switch. Sw it ch 2 : Turns the auto close timer on or off.
3.3 Limit Switch Adjustments 1. Be sure that power to the operator is OFF. 2. Push the gate to the open position. Ad just the OPEN limit nut so that it is activating the OPEN limit switch. 3. Push the gat e to the close position. Adjust the CLOSE limit nut so that it is activ ating the CLOSE limit switch.
3.4 Reverse Sensitivity Adjustment This vehicular gate operator is equippe d with an in herent (Type A) entrapment sensing system. This system will sense an obstru ction in either the opening or clos ing gate cycles and will cause the gate to reverse direction should an obstruction be encountered.
Page 38 9310-065-E-5-07.
SECTION 4 – OPERA TING INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate controls. Keep the remote control away from children. 3. Always keep peopl e and objects away from g ate.
4.2 Shutdown Conditions Under various entra pment conditions the operator wil l assume either a soft or hard shutdown (alarm) condition. To determine what type of reset acti on is required, y ou will nee d to understand how the different entrapment conditions affect the gate ope rat or.
4.2.3 Hard Shutdown A hard shutdown condition occu rs when the inhe rent entrapme nt protection system has sensed two consecutive obstru ctions before the gate re aches the full open o r full closed position.
4.3 Manual Gate Operation This operator is equi pped with a manual releas e system that will allow th e gate to be pushed open in the event of a power outage or equipment failure. There are two manual release system s that are available on this gat e operator.
4.3.3 Fail-Secure Manual Operation The FAIL-SECURE option locks the gate whe n prim ary (AC) power is removed and requires a keyed release to place the gate in manual operation. Th e FAIL-SECURE option is typically used in CLASS III and CLASS IV applications.
Page 44 9310-065-E-5-07.
SECTION 5 – MAINTENANCE AND TROUBLESHOOTING Inspection and service of this gate op erator by a qualified technici an should be performe d anytime a malfunction is observed or suspected. High cycl e usa ge may req uire more frequent service checks. 5.
5.2 Operator Diagnostics This gate operator is de signed with built-in diag nost ics that will ale rt you to potential or existing problems that the micr oprocessor has detecte d. Specific fault condition s are checked and the operator will signal that a fault exist through the built -in alarm.
5.3 Trouble Shooting Have a good VOM meter to che ck voltages and continuity. A Meg-Ohm meter cap able of checking up to 500 meg-ohms of re sistance is necessary to properly check the integrity of the gro und loops. When a malfunction occurs, isolate the problem to one of three areas: 1) the operator, 2) the loop system, 3) the key ing device s.
Gate opens a short distance, then stops and reverses. • Disconnect the gate from the gate operator and check that the gate slides freely without any binding. • Re-adjust the open reverse sensitivity. • Replace the circuit board. Gate opens but will not close.
5.4 Accessories The following accessory items can be used with the m odel 9310 slide gate operator. Contact Sensor Contact sensor s for use as a secondary ent rapment protection device. Miller Edge, Inc. ME120, ME 123, MG020, MGR20, MGS20 Photo Cell Non-contact (photo cells) sens ors for use as a secondary entrapm ent protection device.
Title: Date: Rev. Dwg . No. DOORKING, I NC., INGLEWOOD , CA 90301 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .
Title: Date: Rev. Dwg . No. DOORKING, I NC., INGLEWOOD , CA 90301 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .
Title: Date: Rev. Dwg . No. DOORKING, I NC., INGLEWOOD , CA 90301 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .
Title: Date: Rev. Dwg . No. DOORKING, I NC., INGLEWOOD , CA 90301 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .
Title: Date: Rev. Dwg . No. DOORKING, I NC., INGLEWOOD , CA 90301 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 .
9310-065-E-5-07 Page 55.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il DKS Enterprises 9310 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del DKS Enterprises 9310 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso DKS Enterprises 9310 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul DKS Enterprises 9310 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il DKS Enterprises 9310, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del DKS Enterprises 9310.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il DKS Enterprises 9310. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo DKS Enterprises 9310 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
