Manuale d’uso / di manutenzione del prodotto 225A del fabbricante Directed Electronics
Vai alla pagina of 19
CONGRA TULA TIONS ENDP ANEL LA Y OUT FEA TURES / SPECIFICA TIONS ENDP ANEL LA Y OUT (cont.) INST ALLA TION TR OUBLESHOO TING WIRING TR OUBLESHOO TING (cont.) PO WER / GROUND TR OUBLESHOO TING (cont.) CONNECTIONS TR OUBLESHOO TING (cont.) CONNECTIONS (cont.
The extended use of a high powered audio system may result in hearing loss or damage. While TUBE DRIVER systems are capable of "Concer t Le v el" volumes with incredible accuracy , they are also designed for you to enjoy at more reasonable levels all of the sonic subtleties created by musicians.
1 Power Bandwidth: 5 Hz -50 KHz T otal Harmonic Distortion: 0.2% or less (A-weighted) Input T opology: Balanced Differential Input Sensitivity: 500mV - 12 volts RMS Input Impedance: 10K Ohms Output Impedance: 2 - 16 Ohms, bridged 4 - 32 Ohms Specifications The TD2200PRO and TD225A amplifiers represent a radical new approach to mobile audio.
Fuse Requirements Recommended Fuse Rating f o r TD2200 i s 10 0 Amps Recommended Fuse Rating f o r TD225A is 10 0 Amps Y ou will need to install an in-line fuse or cir cuit breaker in the power wire within 18” of the battery . This fuse or circuit breaker pr otects your vehic le fr om fire in case the power wire shorts to the vehicle bod y .
Recommended MINIMUM Gauge 3 W arning! Amplifiers Generate Heat! Y ou can mount the TU B E D RIVER in any position, even upside-down. However , you m ust maintain pr oper airflow . Do not install your TU B E D RIVER under carpets or enclose it behind airtight panels.
4 W arning! T o prevent a short to ground, disconnect the negative (-) terminal of the system’s battery before you begin. If the power cable shorts to ground, current will continue to flow until the short is opened, the main fuse blows, the battery explodes, or the wire melts.
5 Follow these simple instructions and ref er to the diagram below to make your speaker connections: • Using at least 16 gauge wire, run wire from the speakers to the amplifier(s) using the same pre.
6 Mixed Mono Output All multi-channel T UBE D RIVERS are capable of being bridged into a 4- Ohm mono output without switches or bridging modules. Y ou can achieve this mono channel by using the left positive (+) speaker connection and the right negative (-) speaker connection.
Input Jacks Y our TUB E D RIVER includes both RCA and Mini-DIN (balanced) inputs. The supplied RCA connections allow you to use TU B E D RIVER with other brands of audio gear . Our Diff erential RCA inputs provide a dr amatic improv ement in noise reduction ov er standard RCA input types .
8 Input Gain Control There is an Input Gain Control located on the end panel under the RCA input jacks. This is not a v olume control! This control matches the output signal voltage of the source unit to the amplifier inputs.
HANDCRAFTED IN THE USA By Precision Power POWER CONNECT POWER W ARM UP 9 P o wer Side 1 3 2 1. PO WER A red light indicates that the amplifiier is turned on (After warm-up sequence). 2. W ARM UP A red light indicated that the tubes are warming up. (Refer to Pg.
1. SPEAKER OUTPUTS/REMO TE(T urn on) After connecting remote and speaker wires plug in the connector here. 2. GAIN CONTR OL Use this control to match the output level of the head unit to the outputs of the amplifier 3. B ALANCED INPUT Plug in the mini-din output from the LDX-33 crossover , LD-3 line driver, or other balanced source here.
11 No Sound Amplifier T urning Down at Normal V olume Do you have 12V at the amplifier ’s connections? Is the W ARM UP LED illuminated? YES NO YES The warm up cycle can take up to 40 sec., Is there sound after that? Y ou’re done Is there signal on the RCA ’s? YES NO Does the amp remote (REM) have 12V? Check all connections.
12 No Sound in One Channel Amplifier T urning D ow n at High V olume YES Reverse the left and right inputs. Check the pre-amp (RCA/Mini-Din) cables for open connections and make corrections. Did you find open connections? NO Y ou’re done SOUND IS NO W IN.
13 Noises While the Engine is On Alternator whine: This noise changes in frequency with engine RPM. Check for: . Excessive input le vel . High resistance in cabling or corr oded and/or loose connections . P olarity of the input cab les If the problem persists, check the whines and pops checklist below .
14 Noises While the Engine is On or Off System hiss: Distor tion: System hiss is a white noise that occurs even when the engine is off. It is usually due to excessively high gain settings. If the hiss is still audible when you disconnect the input cables from the amplifier , check the input level on the amplifier .
15 eject VOLUME BASS TREBLE RIGHT LEFT BALANCE TRACK REVERSE FOWARD 1 2 3 4 8 7 6 5 PPI MAR KET ING DPT Trk 1 LD4 Source Unit TD2200 PRO LD3 Studio Driver System 6 Studio Drive r System 6 Subwoofer TD.
16 AMP RCA Right Input DIF. RCA Left Input INPUT ATTENUATION AMP Left Right MINI-DIN Input DIF. GAIN GAIN Left Right BALANCED/RCA Switch BALANCED/RCA Switch B A CK T O CONTENTS.
Three-Y ear Limited U .S.A. W arranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Directed Electronics 225A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Directed Electronics 225A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Directed Electronics 225A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Directed Electronics 225A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Directed Electronics 225A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Directed Electronics 225A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Directed Electronics 225A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Directed Electronics 225A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
