Manuale d’uso / di manutenzione del prodotto SA446 del fabbricante Delta
Vai alla pagina of 20
INSTRUCTION MANUAL 4" Belt / 6" Disc Sander (Model SA446) P ART NO. 905578 -05-03-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR BEL T / DISC SANDERS WARNING : F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT operate your machine until it is completely assembled and installed according to the instructions.
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the machine.
6 4" BEL T / 6" DISC SANDER P ARTS Fig. 1A Fig. 1B 1 Fig. 1A Sander Parts 1. Motor and Base 2. Disc T able 3. Belt and Pulley Guard 4. Disc Plate 5. Dust Chute 6. Support Rod 7. Lower Disc Guard 8. Sanding Disc 9. Backstop 10. Miter Gage 11.
7 ASSEMBL Y INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE SANDER TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE OWNERS MANUAL. Fig. 2 Fig. 3 Fig. 4 2. Check to see if the belt (A) Fig.
8 Fig. 8 Fig. 6 Fig. 7 Fig. 5 ASSEMBLING BEL T AND PULLEY GUARD Assemble the belt and pulley guard (A) Fig. 5, to the machine base using the two M6x1x30mm cheese head screws (B), as shown. ASSEMBLING SANDING DISC PLA TE 1. Back the 1/4-20x1/4" hex socket set screw (A) Fig.
9 Fig. 12 Fig. 11 Fig. 10 Fig. 9 ASSEMBLING SANDING DISC 1. Make sure sanding disc plate (A) Fig. 9, is clean. 2. Peel backing from sanding disc and pr ess disc (B) firmly into position all the way around the sanding plate, as shown in Fig. 9. ASSEMBLING LOWER COVER FOR SANDING DISC Assemble the lower cover (A) Fig.
10 Fig. 15 Fig. 16 Fig. 14 Fig. 13 ASSEMBLING DUST CHUTE Align the three holes in the dust chute (A) Fig. 13 with the three holes in the left side of the sanding base. Place a M5.3 flat washer onto a M5x.08x10mm pan head screw (B) Fig. 13, and insert screw thr ough hole in dust spout and thread into taped hole in sander base.
11 Fig. 18 3. An alternate method of securing the sander to a supporting surface is to fasten the sander base to a mounting board 18" x 24" minimum size. The diagram, shown in Fig. 17, illustrates the size and center to center distance of the holes to be drilled in the mounting board.
12 Fig. 25 CHANGING POSITION OF SANDING ARM 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. The sanding arm (A) can be used in the horizontal position, as shown in Fig. 25; vertical position, as shown in Fig. 26; or any angle in between by loosening screw (B), positioning the arm (A) to the desired angle and tightening screw (B).
13 Fig. 28 Fig. 29 Fig. 30 Fig. 31 3. Place a square (B) Fig. 29, on the sanding belt with one end of the square against the backstop, and check to see if the backstop is square with the sanding belt. 4. If an adjustment is necessary , loosen scr ew (C) Fig.
14 Fig. 32 Fig. 33 Fig. 34 Fig. 35 3. If an adjustment to the table is necessary , loosen the three scr ews (B) Fig. 34, that fasten the table to the table mounting bracket and trunnion and adjust the table accordingly - then tighten the thr ee scr ews (B).
15 Fig. 39 Fig. 38 Fig. 37 Fig. 36 USING T ABLE ASSEMBL Y WITH SANDING BEL T When the sanding arm (A) Fig. 36, is used in the vertical position, the complete table assembly (B) can be moved from the disc unit to the belt unit as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE.
16 Fig. 40 Fig. 41 Fig. 42 Fig. 43 REPLACING SANDING BEL T 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Loosen screw (A) Fig. 40, and r emove backstop (B). 3. Slide tension lever (C) Fig. 41, to the right to release tension on sanding belt and remove sanding belt (D) fr om both sanding drums, as shown.
17 Fig. 44 4. Peel off old disc (E) as shown in Fig. 44. 5. Make sure the disc plate (F) Fig. 44, is clean and peel backing from new sanding disc. Pr ess the new sanding disc firmly into position on disc plate (F) and replace lower cover and table assembly which wer e removed in STEPS 2 and 3 .
18 Fig. 47 SANDING INSIDE CURVES Inside curves can be sanded on the top sanding drum, as shown in Fig. 47. Fig. 48 SANDING OUTSIDE CURVES Outside curves should be sanded on the sanding disc as shown in Fig. 48. WARNING: AL WA YS SAND ON THE LEFT (DOWNWARD) SIDE OF THE SANDING DISC, AS SHOWN.
19 NOTES.
20 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta SA446 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta SA446 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta SA446 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta SA446 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta SA446, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta SA446.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta SA446. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta SA446 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
