Manuale d’uso / di manutenzione del prodotto 40-650 Type 2 del fabbricante Delta
Vai alla pagina of 16
1 DA TED 11-25-98 INSTRUCTION MANUAL P ART NO. 1349463 © Delta International Machinery Corp. 1998 18" V ariable Speed Scr oll Saw (Model 40-650, T ype 2) Quick Quality Quiet.
2 T ABLE OF CONTENTS SAFETY RULES ..................................................................................................................................3 ADDITIONAL SAFETY RULES FOR SCROLL SA WS ............................................
3.
4 ADDITIONAL SAFETY RULES FOR SCROLL SA WS 1. WARNING: Do not operate your scr oll saw until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the oper- ation of Scroll Saws, obtain advice fr om your supervi- sor , instructor or other qualified person.
5 Fig. 2 UNP ACKING AND CLEANING Y our new scroll saw and stand is shipped complete in one container . Carefully unpack the saw , stand and all loose items from the shipping container . Figure 2 illustrates the saw and all loose items and Figur e 3 illustrates the stand and all related parts.
6 Fig. 3 ASSEMBLING ST AND 1. Assemble the stand, as shown in Fig. 4, using the 24 carriage bolts, flat washers and hex nuts. NOTE: The round holes on the top of the two top braces (A) are to be positioned toward the r ear leg (B) and all three legs are positioned outside the bottom shelf and top braces.
7 Fig. 5 Fig. 6 Fig. 7 Fig. 8 3. Figure 8 illustrates the saw (H) fastened to the stand (J). Place the stand on a level sur- face and securely tighten all stand mounting hardwar e. 2. Fasten the rear of the saw to the stand using the two 5/8" long screws (F) Fig.
8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 ASSEMBLING HOLDDOWN FOOT 1. With wrench supplied, assemble holddown foot (A) Fig. 10, to rod (B) using 1/2² hex sock- et head screw (C) with lockwasher and flat washer . Prongs of holddown foot (A) should straddle blade.
9 CONNECTING SCROLL SAW TO POWER SOURCE IMPORT ANT : BEFORE CONNECTING THE SAW TO THE POWER LINE, MAKE SURE THE SWITCH IS IN THE “OFF” POSITION. Fig.
10 F ASTENING ST AND TO SUPPOR TING SURF ACE If there is any tendency for the scr oll saw to move during operation, the scroll saw stand must be fastened to the floor . Fig. 17 OPERA TING CONTROLS AND ADJUSTMENTS ON-OFF POWER SWITCH The on-off switch (A) Fig.
11 Fig. 18 DUST BLOWER A dust blower (A) Fig. 18, is provided, and can be moved to direct air to the most ef fective point on the cutting line. ADJUSTING BLADE TENSION T ension is applied to the blade when the blade tension lever (A) Fig. 19, is in the rear position, as shown.
12 ADJUSTING CLAMPING ACTION OF BLADE HOLDERS Differ ent widths of scroll saw blades will make it necessary to adjust the clamping action of the blade holders. It should be noted, however , that very little adjustment is necessary and very little clamping force is requir ed to hold the blade satisfactorily .
13 Fig. 25 3. Push blade holder clamping lever (C) Fig. 25, to the rear as shown. This will automatically r elease the blade (D) from the upper blade holder (E). 4. Push lower blade holder clamping lever (F) Fig. 26, to the rear . This will automatically release blade (D) fr om lower chuck.
14 Fig. 27 Fig. 28 Fig. 29 Fig. 31 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS FOR T ABLE 1. Loosen table lock handle and move the table all the way to the left and tighten table lock handle. 2. Using a square (A) Fig. 29, check to see if the table is 90 degrees to the saw blade, as shown.
15 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSH- ES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed.
16 BLADE BREAKAGE Blade breakage is usually caused by one or mor e of the following: 1. Bending the blade during installation. 2. Improper blade tension. 3. Improper blade selection for the work being cut. 4. Forcing the work into the blade too rapidly .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta 40-650 Type 2 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta 40-650 Type 2 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta 40-650 Type 2 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta 40-650 Type 2 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta 40-650 Type 2, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta 40-650 Type 2.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta 40-650 Type 2. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta 40-650 Type 2 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
