Manuale d’uso / di manutenzione del prodotto 28-263 del fabbricante Delta
Vai alla pagina of 17
INSTRUCTION MANUAL DA TED 4-15-00 P ART NO. 426-02-651-0037 Copyright © 2000 Delta Machinery Platinum Edition 14" Band Saw (Model 28-263) If you have any problems with your new Delta Power T ool, please call us toll free. Have your model and serial numbers ready .
2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazards involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possi- bility of personal injury .
3 ADDITIONAL SAFETY RULES FOR BAND SA WS 1. ADJUST the upper blade guide about 1 / 8 above the material being cut. 2. MAKE SURE that blade tension and blade tracking are pr operly adjusted. 3. STOP the machine and wait for the blade to come to a complete stop before r emoving scrap pieces from the table.
4 Fig. 5 B C A 3. Remove two mounting screws, one of which is shown at (E) Fig. 2, that ar e holding motor (F) to the top of stand (A). IMPOR T ANT : DO NOT REMOVE CABLE TIE (G) THA T IS HOLDING SWITCH CORD (H) TO VERTICAL MOUNTING BAR (J), UNLESS YOU ARE USING THE ACCESSOR Y 28-984 HEIGHT A TT ACHMENT ON THE BAND SAW .
5 Fig. 6 Fig. 7 B D F A C C A B D ASSEMBLING BAND SA W TO ST AND 1. Car efully place the band saw (A) Fig. 6, onto the band saw stand (B). NOTE: Position the band saw so the pulley (C) is over the opening (D) in the stand.
6 Fig. 9 ASSEMBLING SWITCH 1. MAKE CERT AIN THE BAND SAW IS DISCON- NECTED FROM THE POWER SOURCE . 2. CAUTION: THE ST ART/STOP SWITCH-TO- MOTOR CORD (F) FIG. 9, IS TIED TO VERTICAL MOUNTING POST (G) OPPOSITE THE MOTOR PUL- LEY . THIS CABLE TIE (H) PREVENTS THE SWITCH- TO-MOTOR CORD (F), FROM CONT ACTING THE BEL T OR MOTOR PULLEY DURING OPERA TION.
7 CONNECTING BAND SAW TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp fuse. Have a certified electrician r eplace or repair a worn cord immediately .
Fig. 16 8 EXTENSION CORDS Use only three-wir e extension cords which have three-pr ong grounding-type plugs and three-pole r eceptacle which accept the tool’ s plug. Replace damaged or wor n cord immediately . DO NOT A TTEMPT TO REP AIR POWER CORD. OPERA TING CONTROLS AND ADJUSTMENTS ST ARTING AND STOPPING THE SA W 1.
9 9 Fig. 17 T ABLE INSERT Place table insert (A) Fig. 17, into the hole pr ovided in the table surface, making certain the pin (B) in the table engages one of the indents in the table insert. TIL TING THE T ABLE 1. The table on the band saw can be tilted 45 degr ees to the right and 10 degrees to the left.
10 Fig. 21 Fig. 22 Fig. 23 C 10 ADJUSTING BLADE TENSION DISCONNECT MACHINE FROM POWER SOURCE. On the back of the upper wheel slide bracket, there is a series of graduations. These indicate the proper tension for various widths of blades. With the blade on the wheels, turn the knob (A) Fig.
11 11 Fig. 24 ADJUSTING UPPER BLADE GUIDE ASSEMBL Y DISCONNECT MACHINE FROM POWER SOURCE. The upper blade guide assembly (A) Fig. 24, should always be set as close as possible to the top surface of the material being cut by loosening lock knob (B) and moving the guide assembly (A) to the desired position.
12 12 ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPOR T BEARING DISCONNECT MACHINE FROM POWER SOURCE. The lower blade guides and lower blade support bearing should be adjusted at the same time as the upper guides and bearing as follows: 1. The lower blade guides (A) Fig.
13 BAND SA W BLADES A band saw blade is a delicate piece of steel that is sub- jected to tremendous strain. Y ou can obtain long use from a band saw blade if you give it fair tr eatment. B ensure you use blades of the pr oper thickness, width, and temper for the various types of material to be cut.
ACCESSORIES The testing of this unit has been accomplished with the following accessories. For safest operation, it is recommended that only these accessories be used with this unit. WARNING: Since accessories other than those listed have not been tested with this unit, use of such accessories could be hazardous.
15 15 15 Printed in U.S.A. DEL T A/PORTER-CABLE GUARANTEE Delta is proud of the quality power tools it sells. The component parts of our tools are inspected at various stages of production and each finished tool is subjected to a final check before being packaged for shipment.
.
The following are trademarks of POR TER-CABLE • DEL T A Corporation (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Delta 28-263 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Delta 28-263 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Delta 28-263 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Delta 28-263 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Delta 28-263, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Delta 28-263.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Delta 28-263. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Delta 28-263 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
