Manuale d’uso / di manutenzione del prodotto 9100 del fabbricante Dell
Vai alla pagina of 51
Dell™Inspiron™XPSandInspiron9100ServiceManual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth™Card Hard Drive Fans Hinge .
Back to Contents Page Before You Begin Dell™Inspiron™XPSandInspiron9100ServiceManual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer 1.
11. Remove any installed memory modules , Mini PCI cards , and devices , including a second battery if one is installed. 12. Remove the hard drive .
Screw Identification When you are removing and replacing components, photocopy " Screw Identification " as a tool to lay out and keep track of the screws.
Back to Contents Page Display Ground Screw: (1 each) Palm Rest: (3 each) (4 each) Video Card: (4 each) Speakers:.
Back to Contents Page Flashing the BIOS Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. 2. Insert the BIOS update program floppy disk or CD, and turn on the computer.
Back to Contents Page Bluetooth™Card Dell™Inspiron™XPSandInspiron9100ServiceManual If you ordered a Bluetooth card with your computer, the card is already installed. 1. Follow the instructions in " Preparing to Work Inside the Computer .
Back to Contents Page Microprocessor Module Dell™Inspiron™XPSandInspiron9100ServiceManual Removing the Microprocessor Module 1. Follow the instructions in " Preparing to Work Inside the Computer .
9. Lift out the microprocessor module. Installing the Microprocessor Module 1. Align the pin - 1 corner of the microprocessor module with the pin - 1 corner of the ZIF socket, and insert the microprocessor module. When the microprocessor module is correctly seated, all four corners are aligned at the same height.
Back to Contents Page Display Assembly and Display Latch Dell™Inspiron™XPSandInspiron9100ServiceManual Display Bezel Display Panel Display Latch 1. Follow the instructions in " Preparing to Work Inside the Computer .
6. Use the pull - tab to disconnect the display cable. 7. Lift the display out of the computer at a 90 - degree angle. Display 1 display cable 2 antenna cab.
Display Bezel 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display . 3. Remove the six rubber display bumpers and two screw covers. 4. Remove the six M2.5 x 6 - mm screws and two M2.
Display Panel 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display . 3. Remove the display bezel . 4. Remove the M2 x 3 - mm ground screw that attaches the display - panel ground wire to the back display cover.
7. Press in both sides of the top flex - cable connector, and pull the top flex - cable connector away from the display connector. 8. Use the pull - tab to disconnect the bottom flex - cable connector from the inverter connector.
1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the display . 3. Remove the display bezel . 4. Remove the two M2.5 x 4 - mm screws and remove the display latch. Back to Contents Page 1 M2.
Back to Contents Page Fans Dell™Inspiron™XPSandInspiron9100ServiceManual The two fans are located on the bottom of the computer, one with screws labeled "F2" (fan 2) and one with screws labeled "F3" (fan 3).
5. Use the fan release lever to lift the fan out of the computer. When replacing fan 2, press down on the fan surface labeled "Press here" to securely seat the fan in place. To remove fan 3: 1. Unscrew the two captive screws labeled "F3.
.
Back to Contents Page Hard Drive Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn over the computer and remove the M3 x 3 - mm screw.
6. Replace and tighten the screw. 7. Use the Operating System CD to install the operating system for your computer. For instructions, see "Reinstalling Microsoft Windows XP" in your Owner's Manual . 8. Use the Drivers and Utilities CD to install the drivers and utilities for your computer.
Back to Contents Page Hinge Covers Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left and right hinge covers: a.
c. Open the display all the way (180 degrees) so that it lies flat against your work surface. d. Lift the center hinge cover just enough to access the flex - cable connector. e. Using the pull - tab, disconnect the center – hinge - cover flex cable from the system board connector.
Back to Contents Page Keyboard Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Open the display. 3. Remove the center hinge cover .
Back to Contents Page .
Back to Contents Page Keyboard Bracket Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left, right, and center hinge covers .
Back to Contents Page Display Release Latch Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left, right, and center hinge covers .
Back to Contents Page Modem Dell™Inspiron™XPSandInspiron9100ServiceManual Removing the Modem 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left, right, and center hinge covers .
2. Align the connector on the bottom of the modem with the modem connector on the system board and then press down on the right side of the modem to seat both connectors. 3. Replace the M2.5 x 3 - mm screw. Back to Contents Page NOTICE: Ensure that the modem cable is routed correctly when you replace the modem.
Back to Contents Page Palm Rest Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left, right, and center hinge covers .
Back to Contents Page 1 M2.5 x 6 - mm screws (4) 2 touch - pad connector.
Back to Contents Page Pin Assignments for I/O Connectors Dell™Inspiron™XPSandInspiron9100ServiceManual USB Connector Video Connector S- Video TV - Out.
IEEE 1394 Connector DVI - I Connector S- Video Pin Signal 1 GND 2 GND 3 DLUMA - L 4 DCRMA - L Composite Video Pin Signal 5 NC 6 DCMPS - L 7 .
Back to Contents Page 7 DDC DATA 19 TMDS DATA0/5 SHLD 8 ANALOG VERT SYNC 20 TMDS DATA5 – 9 TMDS DATA1 – 21 TMDS DATA5+ 10 TMDS DATA1+ 22 TMDS CL.
Back to Contents Page Reserve Battery Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the center hinge cover .
Back to Contents Page Speakers Dell™Inspiron™XPSandInspiron9100ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the left, right, and center hinge covers .
Back to Contents Page System Board Dell™Inspiron™XPSandInspiron9100ServiceManual Removing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer.
12. With the front of the computer facing you, lift the system board assembly from the right side, swinging it up, then lift the left side and draw the system board assembly out of the computer. Installing the System Board 1. Perform all of the steps in " Removing the System Board " in reverse order.
Back to Contents Page System Components Dell™Inspiron™XPSandInspiron9100ServiceManual Back to Contents Page NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Back to Contents Page Microprocessor Thermal - Cooling Assembly Dell™Inspiron™XPSandInspiron9100ServiceManual Removing the Microprocessor Thermal - Cooling Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer .
.
Back to Contents Page Dell™Inspiron™XPSandInspiron9100ServiceManual Foracompletelistofabbreviationsandacronyms,seetheDell™InspironHelpfile.Toaccessthehelpfile,seetheOwner'sManualforyourDellcomputer.
Back to Contents Page Memory Module, Mini PCI Card, and Devices Dell™Inspiron™XPSandInspiron9100ServiceManual Memory Module Mini PCI Card Devices Memory Module 1. Follow the instructions in " Preparing to Work Inside the Computer .
4. Ground yourself and install the new memory module: a. Align the notch in the module edge connector with the tab in the connector slot. b. Slide the module firmly into the slot at a 45 - degree angle, and rotate the module down until it clicks into place.
If you ordered a Mini PCI card with your computer, the card is already installed. 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn over the computer. 3. Unscrew the captive screw labeled "C" and remove the Mini PCI card cover.
5. Align the Mini PCI card with the connector at a 45 - degree angle, and press the Mini PCI card into the connector until it clicks. 6. Connect the antenna cables to the Mini PCI card. 1 securing tabs NOTICE: To avoid damaging the antenna cables or the Mini PCI card, never place the cables under the card.
7. Replace the cover and tighten the captive screw. Devices Your computer ships with an optical drive installed in the module bay. Removing and Installing Devices While the Computer Is Turned Off 1. Press the device latch release.
3. Push the new device into the bay until it clicks. Removing and Installing Devices While the Computer Is Running 1. Before ejecting the device, double - click the Safely Remove Hardware icon on the taskbar, click the device you want to eject, and click Stop .
4. Push the new device into the bay until it clicks. The operating system automatically recognizes the device. 5. If necessary, enter your password to unlock your computer.
Back to Contents Page Video Card Dell™Inspiron™XPSandInspiron9100ServiceManual If you ordered a video card with your computer, it is already installed. To remove and replace a video card: 1. Follow the instructions in " Preparing to Work Inside the Computer .
Back to Contents Page Subwoofer Dell™Inspiron™XPSandInspiron9100ServiceManual If you ordered a subwoofer with your computer, it is already installed. To remove and replace a subwoofer: 1. Follow the instructions in " Preparing to Work Inside the Computer .
5. Connect the cable to the subwoofer connector. 6. Replace the battery in the battery bay. Back to Contents Page 1 battery 2 cable 3 subwoofer 4 subwoofer cabl.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dell 9100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dell 9100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dell 9100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dell 9100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dell 9100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dell 9100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dell 9100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dell 9100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
