Manuale d’uso / di manutenzione del prodotto 5548P del fabbricante Dell
Vai alla pagina of 20
Dell PowerConnect 5500 Series Getting Started Guide Regulatory Models: PowerConnect 5524, 5524P , 5548, 5548P ContaxGS.book Page 1 Frid ay, August 20, 2010 1:53 PM.
Notes, Cautions, and W arnings NOTE: A NOTE indicates important in formation that helps you make better use of your system. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WAR NI NG : A WARNING indicates a potential for property damage, personal injury , or death.
Contents 3 Contents 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . 5 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Site Preparation . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking . . . . . . . . . . . . . . . .
4 Contents 3 Configuring the Switch . . . . . . . . . . . . . 13 Configuration Work Flow . . . . . . . . . . . . . . . . 13 Connecting the Switch to the T erminal . . . . . . . . . 14 Booting the Switch . . . . . . . . . . . . . . . . . . . . 15 Configuring the Stack .
Getting Started Guide 5 Installation Overview This guide describes how to install and run the P owerConnect 5500 series switches. F or more information, see the Dell P owerConnect 5500 Series User Guide , available on your Documentation CD, or check the Dell Support website at support.
6 Installation • Cabling — The cabling is routed to avoid sou rces of electrical noise, such as radio transmitters, broadcast ampl ifiers, power lines, and fluorescent lighting fixtures. • Ambient Requirements — The ambient unit operating temperatur e range is 0 to 45ºC (32 to 113ºF) at a re lative humidity of 10% to 90%, non- condensing.
Installation 7 Installing the Switch The P owerConnect 5500 Series switches can be: • Installed o n a rack • Placed on a flat surface Installing in a Rack CAUTION: Disconnect all cables from the unit before mounting the switch in a rack or cabinet.
8 Installation 3 Repeat the process for the rack-mountin g bracket on the other side of the switch. 4 Insert the unit into the 48.26-cm (19-inch) rack, ensuring that the rack-mounting holes on the switch l ine up to the mounting holes on the rack. 5 Secure the unit to the rack with the rack scr ews (not provided).
Getting Started Guide 9 Stacking Overview Each switch is a member in a stack, although the stack may consist of only a single switch. Up to eight switches are supported per stack. All stacks must have a Master unit, and may have a Master Backup unit. All other switches are connected to the stack as members (slaves).
10 Stacking F igur e 2-1 shows this process. Figure 2-1. Stacking Cable Diagram HDMI Ports F r o n t P a n e l HDMI Ports F r o n t P a n e l HDMI Ports F r o n t P a n e l F r o n t P a n e l HDMI Ports ContaxGS.
Stacking 11 Unit ID Assignment Each switch in the stack has a unique uni t ID that defines the unit’s position and function in the stack. F igur e 2-2 describes the stacking LEDs on the front panel of the switch.
12 Stacking Manual Assignment T o assign unit IDs to the switches in the stack, do the following for each switch in the stack: 1 Connect the switch to the terminal, as described in "Connecting the Switch to the T erminal". 2 T urn on the switch to begin auto boot and press Return or Esc to abort and enter the Start Up menu.
Getting Started Guide 13 Configuring the Switch This section describes the configuratio n that must be performed after the switch is installed and connected to power supplies. Additional advanced functions ar e described in the Dell P owerConnect 5500 Series User Guide on the Documentation CD.
14 Configuring the Switch Connecting the Switch to the T erminal The switch is configured and monitor ed through a terminal desktop system that runs terminal emulation software.
Configuring the Switch 15 Booting the Switch After the local terminal is connected, turn on power . The switch then goes through power -on self -test (POST). PO ST runs every time the switch is started and checks hardwar e componen ts, to determine if the switch is operational before completely booting.
16 Configuring the Switch Configuring the Stack The switch is always considered to be a stack of switches even if the stack only contains a single switch. If there is mo r e than one switch in the stack, each switch must be configured individual ly . See "Unit ID Assignment" for instructions on how to configure the stack.
Configuring the Switch 17 • The IP addr ess to be assigned to the VLAN 1 interface through which the switch is to be managed (by d efault, every external and internal port is a member of the VLAN 1).
18 Configuring the Switch To manage the switch usin g SNMP (required for Dell Network Manager) you can: • Setup the initial SNMP version 2 account now. • Return later and set up the SNMP version account. For more information on setting up a SNMP version 2 account, see the user documentation.
Configuring the Switch 19 7 Set up user account privilege level, as follows: The following information is displayed: Now we need to set up y our initial privilege (Level 15) user account. Th is account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later.
20 Configuring the Switch 11 P ress Enter . The following information is displayed: Finally, set up t he default gateway. Please enter the IP address of the gateway from which this network is reachable (e.g. 192.168.2.1).D efault gateway (A.B.C.D):[0.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dell 5548P è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dell 5548P - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dell 5548P imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dell 5548P ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dell 5548P, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dell 5548P.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dell 5548P. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dell 5548P insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
