Manuale d’uso / di manutenzione del prodotto 1340 del fabbricante Dell
Vai alla pagina of 39
Dell™StudioXPS™1340ServiceManual Notes, Notices, and Cautions Information in this document is subject to change without notice. © 2008DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Base Cover Dell™StudioXPS™1340ServiceManual Removing the Base Cover Replacing the Base Cover Removing the Base Cover 1. Ensure that the computer is turned off. 2.
Back to Contents Page Battery Latch Assembly Dell™StudioXPS™1340ServiceManual Removing the Battery Latch Assembly Replacing the Battery Latch Assembly Removing the Battery Latch Assembly 1.
4. Replace the mylar tapes. Ensure that the newly installed latch moves smoothly and freely when pushed and released. 5. Follow the instructions in Replacing the System Board . Back to Contents Page NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer.
Back to Contents Page Before You Begin Dell™StudioXPS™1340ServiceManual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer This section provides procedures for removing and installing the components in your computer.
2. Turn off your computer (see Turning Off Your Computer ). 3. Disconnect all telephone or network cables from the computer. 4. Press and eject any installed cards from the ExpressCard slot and the 8 - in -- 1 Memory Card Reader. 5. Disconnect your computer and all attached devices from their electrical outlets.
Back to Contents Page Flashing the BIOS Dell™StudioXPS™1340ServiceManual Flashing the BIOS From a CD Flashing the BIOS From the Hard Drive If a BIOS upgrade CD is provided with the new system board, flash the BIOS from the CD.
.
Back to Contents Page Coin - Cell Battery Dell™StudioXPS™1340ServiceManual Removing the Coin - Cell Battery Replacing the Coin - Cell Battery Removing the Coin - Cell Battery 1. Follow the instructions in Before You Begin .
Back to Contents Page Processor Dell™StudioXPS™1340ServiceManual Removing the Processor Installing the Processor Removing the Processor 1. Follow the instructions in Before You Begin .
Installing the Processor 1. Align the pin - 1 corner of the processor so that it points to the triangle on the ZIF socket, and insert the processor into the ZIF socket. When the processor is correctly seated, all four corners are aligned at the same height.
Back to Contents Page Processor Heat Sink Dell™StudioXPS™1340ServiceManual Central Processor Heat Sink Graphic Processor Heat Sink/Thermal Fan Central Processor Heat Sink Removing the Central Processor Heat Sink 1.
3. Tighten the four captive screws that secure the central processor heat sink to the system board. 4. Replace the rear caps (see Replacing the Rear Caps ). 5. Replace the base cover (see Replacing the Base Cover ). 6. Slide the battery into the battery bay until it clicks into place.
3. Tighten the two captive screws and replace the other two screws that secure the graphic processor heat sink to the system board. 4. Connect the thermal fan cable to the system board connector. 5. Replace the central processor heat sink (see Replacing the Central Processor Heat Sink ) 6.
Back to Contents Page Display Assembly Dell™StudioXPS™1340ServiceManual Removing the Display Assembly Replacing the Display Assembly Removing the Display Assembly 1. Follow the instructions in Before You Begin .
8. Disconnect the display cable, power light cable, and camera cable from their system board connectors and dislodge the cables from their routing guides. 9. Remove the four screws (two on either side) that secure the display assembly to the computer base.
Back to Contents Page eSATA Connector Dell™StudioXPS™1340ServiceManual Removing the eSATA Connector Replacing the eSATA Connector Removing the eSATA Connector 1. Follow the instructions in Before Working Inside Your Computer .
5. Replace the system board (see Replacing the System Board ). 6. Replace the display assembly (see Replacing the Display Assembly ). Back to Contents Page NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer.
Back to Contents Page Hard Drive Dell™StudioXPS™1340ServiceManual Removing the Hard Drive Replacing the Hard Drive Removing the Hard Drive 1. Follow the instructions in Before You Begin .
7. Remove the four screws that secure the hard drive bracket to the hard drive and remove the bracket. Replacing the Hard Drive 1. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive.
Back to Contents Page Rear Caps Dell™StudioXPS™1340ServiceManual Removing the Rear Caps Replacing the Rear Caps Removing the Rear Caps 1. Follow the instructions in Before You Begin .
Back to Contents Page Keyboard Dell™StudioXPS™1340ServiceManual Removing the Keyboard Replacing the Keyboard Removing the Keyboard 1. Follow the instructions in Before You Begin . 2. Remove the palm rest (see Removing the Palm Rest ).
Replacing the Keyboard 1. Replace the keyboard on the palm rest. 2. Align the keyboard shield over the screw holes on the palm rest. 3. Replace the ten screws that secure the keyboard and the shield to the palm rest. 4. Connect the backlit keyboard cable (availability varies according to region) to the connector.
Back to Contents Page Status Light Board Dell™StudioXPS™1340ServiceManual Removing the Status Light Board Replacing the Status Light Board Removing the Status Light Board 1. Follow the instructions in Before You Begin .
.
Back to Contents Page Memory Dell™StudioXPS™1340ServiceManual Removing the Memory Module(s) Replacing the Memory Module(s) You can increase your computer memory by installing memory modules on the system board.
2. Slide the module firmly into the slot at a 45 - degree angle, and press the module down until it clicks into place. If you do not feel the click, remove the module and reinstall it. 3. Replace the base cover (see Replacing the Base Cover ).
Back to Contents Page Wireless Mini - Card Dell™StudioXPS™1340ServiceManual Removing the Mini - Card Replacing the Mini - Card If you ordered a wireless Mini - Card with your computer, the card is already installed.
4. Remove the screw that secures the Mini - Card to the system board. 5. Lift the Mini - Card out of the system board connector. Replacing the Mini - Card 1. Remove the new Mini - Card from its packaging. 2. Insert the Mini - Card connector at a 45 - degree angle into the appropriate system board connector.
Back to Contents Page .
Back to Contents Page Optical Drive Dell™StudioXPS™1340ServiceManual Removing the Optical Drive Replacing the Optical Drive Removing the Optical Drive 1. Follow the instructions in Before You Begin .
6. Detach the interposer from the optical drive. Replacing the Optical Drive 1. Attach the interposer to the optical drive. 2. Place the optical drive in the computer base. 3. Replace the two screws that secure the optical drive to the system board.
Back to Contents Page Palm Rest Dell™StudioXPS™1340ServiceManual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest 1. Follow the instructions in Before You Begin . 2.
6. Starting at the back center of the palm rest, use your fingers to gently ease the palm rest from the computer base by lifting the inside of the palm rest while pulling on the outside. 7. Disconnect the daughter board cable and keyboard cable from the respective system board connectors.
Back to Contents Page AC Adapter Connector Dell™StudioXPS™1340ServiceManual Removing the AC Adapter Connector Replacing the AC Adapter Connector Removing the AC Adapter Connector 1. Follow the instructions in Before You Begin .
4. Replace the eSATA connector (see Replacing the eSATA Connector ). Back to Contents Page .
Back to Contents Page System Board Dell™StudioXPS™1340ServiceManual Removing the System Board Replacing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer.
13. Disconnect the display cable, power light cable, camera cable, and status light board cable from the system board connector. 14. Lift the system board at an angle towards the side of the computer and disconnect the eSATA cable and AC adapter cable from the system board.
14. Replace the coin - cell battery (see Replacing the Coin - Cell Battery ). 15. Replace the base cover (see Replacing the Base Cover ). 16. Turn on the computer. 17. Insert the BIOS upgrade CD that accompanied the replacement system board into the appropriate drive.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dell 1340 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dell 1340 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dell 1340 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dell 1340 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dell 1340, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dell 1340.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dell 1340. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dell 1340 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
