Manuale d’uso / di manutenzione del prodotto 7000 del fabbricante Datalogic Scanning
Vai alla pagina of 204
PowerScan® 7000 2D Imager Product Reference Guide.
Datalogic Scanning, Inc. 959 T erry Street Eugene, Oregon 97402 T elephone: (541) 683-5700 F ax: (541) 345-7140 An Unpublished W ork - All rights reser ved.
Product Reference Guide i Table of Contents Chapter 1 Getting Started ......................................................... 1-1 About This Manual ............................................................................ 1-1 Manual Conventions .
ii PowerScan® 7000 2D Scan Stand Mode ..............................................................................3-7 Scan Stand Symbol ..................................................................... 3-7 Presentation Mode ....................
Product Reference Guide iii To Add a Data Format ................................................................. 5-2 Other Programming Selections ..................................................... 5-3 Data Format Editor Commands .................
iv PowerScan® 7000 2D China Post .......................................................................... 6-43 Korea Post .......................................................................... 6-44 QR Code ......................................
Product Reference Guide v Installing Power Image Configurator from the Web ......................... 9-4 Chapter 10 Serial Programming Commands ............................ 10-1 Conventions .............................................................
vi PowerScan® 7000 2D.
Product Reference Guide 1-1 Chapter 1 Getting Started The P owerScan ® 7000 2D imager marks a new performance level for handheld area imagers. They deliver aggr essive read rates and depths of field on 1D, stacked linear , and matrix codes.
Getting Started 1-2 PowerScan ® 7000 2D Manual Conventions The symbols listed below ar e used in this manual to notify the reader of key issues or procedures that must be observed when using the imag.
LED and Beeper Indications Product Reference Guide 1-3 LED and Beeper Indications The imager is equipped with a beeper (speaker) and two indicator LEDs; one green and one yello w .
Getting Started 1-4 PowerScan ® 7000 2D Plug and Play Plug and Play bar codes pro vide instant imager set up for commonly used interfaces. Connecting the imager with an RS-232 Serial Port 1. T urn off power to the terminal/computer . 2. Connect the appropriate interface cable to the imager .
Plug and Play Product Reference Guide 1-5 3. Plug the serial connector into the serial port on your computer . T ighten the two screws to secur e the connector to the port. 4. If the terminal does not support P ower Off the T erminal (P .O.T .) connections plug the power supply into the host connector and the AC o utl et .
Getting Started 1-6 PowerScan ® 7000 2D 2. The imager beeps. 3. V erify imager operation by scanning the part number bar code from the back co ver of this manual. F or additional USB programming and technical information, visit the website listed on the back co ver of this manual.
Plug and Play Product Reference Guide 1-7 Each bar code above also programs the follo wing suffixes for each sym- bology: USB PC Keyboard or USB Macintosh Key- board Scan one of the following codes to program the imager for USB PC Key- board or USB M acintosh Keyboard.
Getting Started 1-8 PowerScan ® 7000 2D USB HID Scan the following code to program the imager for USB HID bar code imagers. Scanning this code changes the terminal ID to 131. USB COM Port Emulation Scan the following code to program the imager to emulate a r egular RS- 232-based COM port.
Plug and Play Product Reference Guide 1-9 ACK/NAK Mode Connecting the imager in Universal Key- board Wedge mode The U niversal Keyboar d W edge (UKB W) model allows an RS-232 transmission or Keyboard W edge mode according to the type of cable connected.
Getting Started 1-10 PowerScan ® 7000 2D 3. Connect one end of the Y cable to the keyboard cable and the other to the keyboard port on the host/computer . 4. Scan the following bar code to program the imager for the UKB W interface. K e y b o a r d Captive Screws Retainer Boss Cable Connector ~p ap2 32 ; 232 C T S 1 ³ .
Product Reference Guide 2-1 Chapter 2 Terminal Interfaces Terminal ID If your interface is not a standard PC A T , refer to Suppor ted T er minals on page 2-2 , and locate the T erminal ID number for your PC.
Terminal Interfaces 2-2 PowerScan ® 7000 2D F or example, an IBM A T terminal has a T erminal ID of 003. Y ou would scan the T erminal ID bar code, then 0 , 0 , 3 from the Programming Chart on page B-5 of this manual, then Save .
Keyboard Country Product Reference Guide 2-3 Keyboard Country Scan the appropriate country code below to program the keyboar d for your country . As a general rule, the following characters are suppor.
Terminal Interfaces 2-4 PowerScan ® 7000 2D Keyboard Country (continued) Latin America Norwa y P oland P or tugal Romania Russia SCS Slov akia Italy Netherlands (Dutch) Spain Sweden Switzerland (Germ.
Keyboard Style Product Reference Guide 2-5 Keyboard Country (continued) Keyboard Style This programs keyboar d styles, such as Caps Lock and Shift Lock. Defa ult = Regu lar . Regular is used when you normally hav e the Caps Lock key off. Caps L ock is used when you normally have the Caps Lock key on.
Terminal Interfaces 2-6 PowerScan ® 7000 2D Automatic C aps Lock i s u s e d i f y o u c h a n g e t h e C a p s L o c k k e y o n a n d o f f . Th e s of t wa re t r ac k s a n d re fl e ct s i f y ou h a ve Ca p s Lo c k o n or o f f ( A T a n d PS/2 only).
Keyboard Modifiers Product Reference Guide 2-7 Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and T urbo M ode. Control + ASCII Mode On The Imager sends key combinations for ASCII control characters for val- ues 00-1F .
Terminal Interfaces 2-8 PowerScan ® 7000 2D RS-232 Modifiers RS-232 Baud Rate Baud Rate sends the data from the imager to the terminal at the specified rate.
RS-232 Modifiers Product Reference Guide 2-9 RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the wor d length at 7 or 8 bits of data per character . If an application requires only ASCII H ex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
Terminal Interfaces 2-10 PowerScan ® 7000 2D RS-232 Receiver Time-Out The unit stays awake to receive data until the RS-232 R eceiver T ime- Out expires. A manual or serial trigger resets the time-out. When an RS-232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out.
RS-232 Modifiers Product Reference Guide 2-11 RS-232 Handshaking RS-232 handshaking is a set of rules concerning the exchange of data between serially communicating devices. If using R TS/CTS handshaking, the imager issues an active R TS signal to the receiving device.
Terminal Interfaces 2-12 PowerScan ® 7000 2D NOTES.
Product Reference Guide 3-1 Chapter 3 Output Image VGA Y ou can set the image size to a VGA r esolution, if necessary , to accom- modate older applications that require a smaller image siz e. When Image V GA is set to On, the resultant image is 640x480 pixels.
Output 3-2 PowerScan ® 7000 2D Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the imager emits on a good read. Default = M edium. Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the imager emits on a good read.
Good Read Indicators Product Reference Guide 3-3 Beeper Duration – Good Read The beeper duration codes modify the length of the beep the imager emits on a good read. Default = N or mal. LED – Good Read The LED indicator can be programmed On or Off in response to a good rea d.
Output 3-4 PowerScan ® 7000 2D Good Read Delay This sets the minimum amount of time before the imager can read another bar code. Default = No D elay .
Trigger Modes Product Reference Guide 3-5 When in serial mode, the imager scans until a bar code has been read or until the deactivate command is sent. In serial mode, the imager can also be set to turn itself off after a specified time has elapsed (see Read Time- Out , which follows).
Output 3-6 PowerScan ® 7000 2D If the unit remains idle during the lo w power time-out interval, the unit goes into low po wer mode. Whenever the trigger is enabled, the low power time-out timer is r eset. NO TE This time-out does not begin until the imager time-out setting has expired.
Scan Stand Mode Product Reference Guide 3-7 Scan Stand Mode When a unit is in Scan St and mode, it remains idle as long as it sees the Scan S tand symbol. (See Scan Stand Symbol that follows.) When a dif- ferent code is presented, the I mager is triggered to read the new code.
Output 3-8 PowerScan ® 7000 2D Presentation LED Timer When an imager is in presentation mode, the LEDs turn off immediately a ft e r a b ar c o de i s d e c od e d. T he i m ag e r c a n be p ro g ra m me d t o c o nt i nu e scanning and to keep the LEDs on for a short time after by scanning the LEDs On bar code below .
Double Read Timeout Product Reference Guide 3-9 Scan the H ands Fr ee T ime-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the Prog ramming Char t on page B-5 , and Save . Default = 5,000 ms. Double Read Timeout This sets the time period before the imager can read the same bar code a second time.
Output 3-10 PowerScan ® 7000 2D LED Power Level This selection allows you to adjust LED and aimer brightness. Off is used when no illumination is needed.
Illumination Lights Product Reference Guide 3-11 Illumination Lights If you want the i llum inat ion l ight s on whil e read ing a bar c ode, scan the Lights On bar code, below . How ever , if you want to turn just the lights off, scan the Lights Off bar code.
Output 3-12 PowerScan ® 7000 2D Aimer Delay The aimer delay allows a delay time for the operator to aim the imager before the picture is taken. U se these codes to set the time between when the trigger is pulled and when the picture is taken.
Aimer Modes Product Reference Guide 3-13 Aimer Modes This feature allows y ou to select from the three options listed below: Aimer Mode Off Aimer M ode is disabled. Interlaced Mode In I nterlaced Mode, the illumination and aiming timing is automatically synchronized to the imager exposure period b y the Optics M odule.
Output 3-14 PowerScan ® 7000 2D duty cycle, even when the imager exposur e time is at its maximum in dark operating environments. Concurrent mode pro vides the brightest appearance of the illumination LEDs of any of the imager operating modes.
Centering Product Reference Guide 3-15 In the example in Figure 3-1 , the gray area is the full imager field of view and the white area is the centering windo w . Bar Code 1 will not be read, while Bar Code 2 will be.The default centering windo w is a 128x96 pixel area in the center of the imager ’ s field of vie w .
Output 3-16 PowerScan ® 7000 2D Scan Centeri ng On , then scan one of the following bar codes to change the top, bottom, left, or right of the centering windo w . Then scan the percent you want to shift the centering window using digits on the Pro- gramming Chart on page B-5 .
Output Sequence Overview Product Reference Guide 3-17 Quick Omnidirectional - This is an abbr eviated search for bar code fea- tures around the center region of an image. This mode quickly r eads all symbologies in any orientation. The Quick Omnidirectional mode may miss some off-center symbols, as well as larger Data Matrix and QR Code symbols.
Output 3-18 PowerScan ® 7000 2D Output Sequence Editor This programming selection allows you to program the I mager to output data (when scanning more than one symbol) in whatever or der your application requires, r egardless of the or der in which the bar codes are scanned.
Output Sequence Overview Product Reference Guide 3-19 5. End Output S equence Editor Scan F F to enter an Output Sequence for an additional symbol- ogy , or Save to save your entries. Other Programming Selections Discard This exits without saving any Output Sequence changes.
Output 3-20 PowerScan ® 7000 2D The breakdown of the command line is sho wn below: SEQBLK sequence editor start command 62 code identifier for Code 39 9999 code length that must match for Code 39, 99.
Output Sequence Overview Product Reference Guide 3-21 Output Sequence Editor Require Output Sequence When an output sequence is Req ui red , all output data must conform to an edited sequence or the imager will not transmit the output data to the host device.
Output 3-22 PowerScan ® 7000 2D Multiple Symbols When this programming selection is turned On , it allows you to read multiple symbols with a single pull of the Imager ’ s trigger . If you press and hold the trigger , aiming the Imager at a series of symbols, it reads unique symbols once, beeping (if turned on) for each read.
Print Weight Product Reference Guide 3-23 Print Weight P rint W eight is used to adjust the way the imager reads M atrix symbols. If a imager will be seeing consistently heavily printed matrix symbols, then a print weight of 6 may impro ve the reading performance.
Output 3-24 PowerScan ® 7000 2D Working Orientation Some bar codes ar e direction-sensitive. F or example, KIX codes and OCR can misread when scanned sideways or upside down. U se the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner .
Product Reference Guide 4-1 Chapter 4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “ message string.
Data Editing 4-2 PowerScan ® 7000 2D Points to Keep In Mind • I t is not necessar y to build a message string. The selections in this chapter are only used if you wish to alter the default settings. Default pr efix = None. Default suffix = N one . • A prefix or suffix may be added or cleared fr om one symbology or all symbologies.
Prefix/Suffix Overview Product Reference Guide 4-3 To Add a Prefix or Suffix: Step 1. Scan the Add Prefix or Add Suffix symbol ( page 4-5 ). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbolog y Char t on page A-1 ) for the symbology to which you want to apply the prefix or suffix.
Data Editing 4-4 PowerScan ® 7000 2D Example: Add a Suffix to a specific symbology T o send a CR (carriage return) S uffix for UPC only: Step 1. Scan Add Suffix . Step 2. Determine the 2 digit hex value from the Symbology Chart (included in ASCII Conv ersion Char t (Code P age 1252) on page A-4 ) for UPC.
Prefix/Suffix Overview Product Reference Guide 4-5 Prefix Selections Suffix Selections Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the imager transmits the function code to the terminal.
Data Editing 4-6 PowerScan ® 7000 2D Intercharacter, Interfunction, and Intermessage Delays Some terminals drop information (characters) if data comes through too quickly . Intercharacter , interfunction, and intermessage delays slow the transmission of data, increasing data integrity .
Intercharacter, Interfunction, and Intermessage Delays Product Reference Guide 4-7 User Specified Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed after the transmission of a particular character of scanned data.
Data Editing 4-8 PowerScan ® 7000 2D Intermessage Delay An intermessage delay of up to 495 milliseconds may be placed between each scan transmission. Scan the Intermessage Delay bar code belo w , then scan the number of milliseconds and the SA VE bar code using the Programming Chart on page B-5 of this manual.
Product Reference Guide 5-1 Chapter 5 Data Formatting Data Format Editor Introduction Y ou may use the Data F ormat Editor to change the imager ’ s output. For example, you can use the Data F ormat Editor to inser t characters at cer- tain points in bar code data as it is scanned.
Data Formatting 5-2 PowerScan ® 7000 2D To Add a Data Format Step 1. Scan the Enter Data Format symbol ( page 5-5 ). Step 2. Primary/Alternate Format Determine if this will be your primary data format, or one of 3 alternate formats. (Alternate formats allow you “single shot” capability to scan one bar code using a different data format.
Data Format Editor Introduction Product Reference Guide 5-3 bols that represent the command you want to enter. 94 alphanumeric characters may be entered for each symbology data format. Step 7. Scan Save from the Programming Chart on page B-5 of this manual to save your entries.
Data Formatting 5-4 PowerScan ® 7000 2D Move Commands F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved ahead.) F6 Move the cursor back “nn” characters from current cursor position.
Data Format Editor Introduction Product Reference Guide 5-5 ED Check to make sure there is a non-numeric ASCII character at the current cursor position.
Data Formatting 5-6 PowerScan ® 7000 2D Alternate Data Formats Alternate formats allow you “ single shot” capability to scan one bar code using a different data format than your primary format.
Product Reference Guide 6-1 Chapter 6 Symbologies This programming section contains the following menu selections. Ref er to Chapter 10 for settings and defaults.
Symbologies 6-2 PowerScan ® 7000 2D Linear Symbologies All Symbologies If you want to decode all the symbologies allo wable for your imager , scan the All S ymbologies On code. If on the other hand, you want to decode only a particular symbology , scan All Symbologies Off follo wed by the On symbol for that particular symbology .
Linear Symbologies Product Reference Guide 6-3 Codabar <Default All Codabar Settings> Codabar Enable Codabar Start / Stop Characters S tart/Stop characters identify the leading and trailing ends of the bar code. Y ou may either transmit, or not transmit Start/S top characters.
Symbologies 6-4 PowerScan ® 7000 2D When Check Character is set to V alidate, but Don ’t T r ansmit , the unit will only read Codabar bar codes printed with a check character , but will not transmit the check character with the scanned data. Codabar Concatenation Codabar supports symbol concatenation.
Linear Symbologies Product Reference Guide 6-5 Codabar Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 2-60. M inimum Default = 4, Maximum Default = 60.
Symbologies 6-6 PowerScan ® 7000 2D Code 39 Check Character No Check Character indicates that the imager reads and transmits bar code data with or without a check character .
Linear Symbologies Product Reference Guide 6-7 Code 39 Append This function allows the imager to append the data from several Code 39 bar codes together before transmitting them to the host computer .
Symbologies 6-8 PowerScan ® 7000 2D Full ASCII If F ull ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character . F or example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.
Linear Symbologies Product Reference Guide 6-9 Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host pr ogram is expecting.
Symbologies 6-10 PowerScan ® 7000 2D When Check Digit is set to V alidate and T ransmit , the imager only r eads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
Linear Symbologies Product Reference Guide 6-11 Code 93 < Default All Code 93 Settings > Code 93 Enable Code 93 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Symbologies 6-12 PowerScan ® 7000 2D Code 2 of 5 <Default All Code 2 of 5 Settings> Code 2 of 5 Enable Code 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Linear Symbologies Product Reference Guide 6-13 IATA Code 2 of 5 <Default All Code IA T A 2 of 5 Settings> IATA Code 2 of 5 Enable IATA Code 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Symbologies 6-14 PowerScan ® 7000 2D M a t r ix 2 o f 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 Enable Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Linear Symbologies Product Reference Guide 6-15 Check Digits Required This option sets whether 1 or 2 check digits are requir ed with Code 11 bar codes. Default = T wo Check Digits. Code 11 Message Length Scan the bar codes below to change the message length.
Symbologies 6-16 PowerScan ® 7000 2D Code 128 <Default All Code 128 Settings> Code 128 Enable ISBT 128 Concatenation In 1994 the I nternational Society of Blood T ransfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner .
Linear Symbologies Product Reference Guide 6-17 Code 128 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 0-80. M inimum Default = 0, Maximum Default = 80.
Symbologies 6-18 PowerScan ® 7000 2D Telepen Telepen Output U sing AIM T elepen Output, the imager reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1).
Linear Symbologies Product Reference Guide 6-19 UPC-A <Default All UPC-A Settings> UPC-A Enable UPC-A Check Digit Transmit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. De fault = On .
Symbologies 6-20 PowerScan ® 7000 2D UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda. UPC-A Addenda Required When Req ui red is scanned, the imager will only read UPC-A bar codes that have addenda.
Linear Symbologies Product Reference Guide 6-21 UPC-A/EAN-13 with Extended Coupon Code U se the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On. UPC-E0 <Default All UPC-E Settings> UPC-E0 M ost U.P .
Symbologies 6-22 PowerScan ® 7000 2D UPC-E0 Addenda Required When Addenda R equired is set to on, the imager will only read UPC-E bar codes that have addenda. Default = N ot Requir ed. UPC-E0 Addenda Separator When this feature is on, there is a space between the data fr om the bar code and the data from the addenda.
Linear Symbologies Product Reference Guide 6-23 UPC-E0 Number System The numeric system digit of a U.P .C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
Symbologies 6-24 PowerScan ® 7000 2D EAN/JAN-13 <Default All EAN/J AN Settings> EAN/JAN-13 Enable EAN/JAN-13 Check Digit Transmit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Linear Symbologies Product Reference Guide 6-25 EAN/JAN-13 Addenda Required When Addenda R equired is set to on, the imager will only read EAN/ JAN-13 bar codes that have addenda. Default = N ot Requir ed. EAN/JAN-13 Addenda Separator When this feature is on, there is a space between the data fr om the bar code and the data from the addenda.
Symbologies 6-26 PowerScan ® 7000 2D EAN/JAN-8 <Default All EAN/J AN-8 Settings> EAN/JAN-8 Enable EAN/JAN-8 Check Digit Transmit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Linear Symbologies Product Reference Guide 6-27 EAN/JAN-8 Addenda Required When Addenda R equired is set to on, the imager will only read EAN/ JAN-8 bar codes that have addenda. Default = N ot Requir ed. EAN/JAN-8 Addenda Separator When this feature is on, there is a space between the data fr om the bar code and the data from the addenda.
Symbologies 6-28 PowerScan ® 7000 2D MSI <Default All MSI Settings> MSI Enable MSI Check Character Different types of check characters ar e used with MSI bar codes. Y ou can program the imager to read MSI bar codes with T ype 10 check char- acters.
Linear Symbologies Product Reference Guide 6-29 MSI Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 4-48. M inimum Default = 4, Maximum Default = 48.
Symbologies 6-30 PowerScan ® 7000 2D RSS-14 < Default All RSS-14 Settings > RSS-14 Enable RSS Limited < Def ault All RSS Limited Settings > RSS Limited Enable * On Off * On Off.
Linear Symbologies Product Reference Guide 6-31 RSS Expanded < Defa ult All RSS Expanded Settings > RSS Expanded Enable RSS Expanded Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Symbologies 6-32 PowerScan ® 7000 2D PosiCode <Default All P osiCode Settings> PosiCode A and B Enable Y o u ha ve t o ha ve P os iCo de A and B on to re ad a ny o f th e P os iCo de s ym- bologies. PosiCode Message Length Scan the bar codes below to change the message length.
Stacked Symbologies Product Reference Guide 6-33 Trioptic Code T rioptic Code is used for labeling magnetic storage media. Stacked Symbologies Codablock F <Default All Codab lock F Settings> Codablock F Enable Codablock F Message Length Scan the bar codes below to change the message length.
Symbologies 6-34 PowerScan ® 7000 2D Code 16K <Default All Code 16K Settings> Code 16K Enable Code 16K Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Stacked Symbologies Product Reference Guide 6-35 Code 49 <Default All Code 49 Settings> Code 49 Enable Code 49 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Symbologies 6-36 PowerScan ® 7000 2D PDF417 < Defa ult All PDF417 Settings > PDF417 Enable PDF417 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Stacked Symbologies Product Reference Guide 6-37 MicroPDF417 < Default All MicroPDF417 Settings > MicroPDF417 Enable MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Symbologies 6-38 PowerScan ® 7000 2D UPC/EAN Version Scan the UPC/EAN V ersion On bar code to decode EAN•UCC Compos- ite symbols that have a UPC or EAN linear component. (This does not affect EAN•UCC Composite symbols with a UCC/EAN-128 or RSS linear component.
Stacked Symbologies Product Reference Guide 6-39 tion is selected, the AIM Symbology I dentifier is reported as “]C1”. If RSS Emulation is selected, the AIM Symbology I dentifier is reported as “]e0.” Any application that accepts EAN•UCC data can be simplified since it only needs to recognize one data carrier type.
Symbologies 6-40 PowerScan ® 7000 2D Postal Codes Postnet Postnet Check Digit Transmit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data. NO TE For best performance when reading a postal symbology , all other postal symbologies should be turned off.
Postal Codes Product Reference Guide 6-41 Planet Code Planet Code Check Digit Transmit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data.
Symbologies 6-42 PowerScan ® 7000 2D British Post Canadian Post Kix (Netherlands) Post NO TE Kix code can misread when scanned sidewa ys or upside down. Use W orking Orientation, page 3-19, if your Kix codes will not usuall y be pre- sented upright to the scanner .
Postal Codes Product Reference Guide 6-43 Australian Post Japanese Post China Post <Default All China P ost Settings> * Off On * Off On.
Symbologies 6-44 PowerScan ® 7000 2D China Post Enable China Post Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 2-80.
Postal Codes Product Reference Guide 6-45 Korea Post Korea Post Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 2-80. M inimum Default = 4, Maximum Default = 48.
Symbologies 6-46 PowerScan ® 7000 2D QR Code This selection applies to both QR Code and Micro QR Code. QR Code Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information.
Postal Codes Product Reference Guide 6-47 Data Matrix Enable Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 1-1500.
Symbologies 6-48 PowerScan ® 7000 2D MaxiCode Enable MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 1-150. Minimum D efault = 1, Maximum Default = 150.
Postal Codes Product Reference Guide 6-49 Aztec Code Enable Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Mes- sage Length Description on page 6-2 for additional information. Mini- mum and Maximum lengths = 1-3750.
Symbologies 6-50 PowerScan ® 7000 2D NOTES.
Product Reference Guide 7-1 Chapter 7 Imaging Commands The imager can be used as a digital camera for capturing, manipulating, and transferring images. Imaging Commands with their modifiers send imaging commands to the imager on a single-use basis, and take effect for the next subsequent image capture.
Imaging Commands 7-2 PowerScan ® 7000 2D IMGSNP Modifiers P - Imaging S tyle: Sets the I mage Snap style. 0P Decoding S tyle. This is similar to the current format for decoding, howev er , this processing allows a few frames to be taken until the exposure parameters are met.
Image Snap - IMGSNP Product Reference Guide 7-3 n D Range: 0 - 255 L - LED S tate : Determi nes if t he LEDs should be on or off, and whe n. Ambient illumination (0L) is preferred for taking pictur es of color docu- ments, such as ID cards, especially when the imager is in a stand.
Imaging Commands 7-4 PowerScan ® 7000 2D Image Ship - IMGSHP An image is taken whenever the trigger of the unit is pressed, or when the Image S nap (IMGSNP) command is processed. The last image is always stored in memory . Y ou may “ ship ” the image by using the IMG- SHP command.
Image Ship - IMGSHP Product Reference Guide 7-5 E - Edge Sharpen: Causes the transmitted image to be conv olved with an edge sharpening filter . Entering a 23E gives the sharpest edges, but also increases noise in the image.
Imaging Commands 7-6 PowerScan ® 7000 2D IR - Image Rotate: 1IR Rotate image 90 degr ees to the right 2IR Rotate image 180 degr ees (upside down) 3IR Rotate image 90 degr ees to the left J - JPEG I mage Quality: Sets the desir ed quality when the JPEG image format is selected.
Image Ship - IMGSHP Product Reference Guide 7-7 n R The right edge of the shipped image corresponds to column n - 1 of the image in memory . Range: 000 - 640. (Default = all columns, or 639 for VGA imager) n T The top edge of the shipped image corresponds to row n of the image in memory .
Imaging Commands 7-8 PowerScan ® 7000 2D 3S ship every 3rd pixel, both horizontally and v ertically U - Document I mage F ilter: Sharpens the edges and smooths the area between the edges of the transmitted text image. The Document Image F ilter enhances images of documents such as ID cards and pr escriptions.
Intelligent Signature Capture - IMGBOX Product Reference Guide 7-9 Intelligent Signature Capture - IMGBOX Intelligent signatur e capture ships only part of an image to the host application. This method reduces transfer time and file size, while sim- plifying signature capture.
Imaging Commands 7-10 PowerScan ® 7000 2D IMGBOX Modifiers D - Pix el Depth: Indicates the number of bits per pixel in the transmit- ted image. 8D 8 bits per pixel, grayscale image 1D 1 bit per pixel, black and white image F - F ile F ormat: Indicates the type of file format in which to sav e the image.
Intelligent Signature Capture - IMGBOX Product Reference Guide 7-11 50K Apply gamma correction for brightening typical document image n K Apply gamma corr ection factor n ( n = 1-255) R - Resolution of S ignature Capture Ar ea: The number of pixels that the imager outputs per each minimum bar width.
Imaging Commands 7-12 PowerScan ® 7000 2D NOTES.
Product Reference Guide 8-1 Chapter 8 OCR Programming U se this section to program the Imager for optical character recognition (OCR). P owerScan 2D models read 6 to 60 point OCR typeface. The 2D imager will read the following fonts: OCR-A 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ ()<>/+-*$ OCR-B $%&'()*+,-.
OCR Programming 8-2 PowerScan ® 7000 2D Y ou can either select an OCR default, or create your own custom tem- plate for the type of OCR format you intend to read. S ee OCR on page 8- 2 for programming codes that will enable your imager to r ead OCR-A, OCR-B, U.
OCR Fonts Product Reference Guide 8-3 OCR-A On allows you to scan characters in the OCR-A font. The default setting allows you to scan any eight digit combination. I f you have cre- ated an OCR template, character combinations that fit the template can be scanned (see Creating an OCR T emplate on page 8-5 ).
OCR Programming 8-4 PowerScan ® 7000 2D MICR E13 B Font MICR E13 B On allows you to scan MICR characters on a bank check. The default setting allows you to scan any eight digit combination. If you have cr eated an OCR template, character combinations that fit the template can be scanned (see Creating an OCR T emplate on page 8-5 ).
OCR Templates Product Reference Guide 8-5 OCR Templates Y ou can create a custom “ template,” or character string that defines the length and content of OCR strings that will be read with your imager . There are several choices when cr eating a custom template for your application.
OCR Programming 8-6 PowerScan ® 7000 2D Template Characters To Add an OCR Template... 1. T urn on the OCR font you want to read ( page 8-2 ). 2. Begin building the template. Scan the Enter OCR Template symbol ( page 8-16 ). 3. Scan the characters for the string.
OCR Templates Product Reference Guide 8-7 Y ou need to read any combination of eight digits. The template would be: dddddddd T o create this template, you would enable the OCR-A font. Scan the Enter OCR Template symbol ( page 8-16 ), then scan the d from the OCR Programming Chart on page B-4 eight times.
OCR Programming 8-8 PowerScan ® 7000 2D T o create this template, you would enable the OCR-A font. Scan the Enter OCR Template symbol ( page 8-16 ). Scan the d from the OCR Pro- gramming Chart on pag.
OCR User-Defined Variables Product Reference Guide 8-9 Y ou can string together as many templates as you need. OCR User-Defined Variables Y ou can create up to two of your ow n user variables for an OCR tem- plate. These variables will repr esent any OCR readable characters.
OCR Programming 8-10 PowerScan ® 7000 2D Consider the following example. This example sho ws serial commands as they would be entered using P owerView . Example: You need to read multiple rows of OCR-A data as shown below: 12345678 ABCDEFGH F irst, enable the OCR-A font.
OCR Check Character Product Reference Guide 8-11 dddddddc T o create this template, you would enable the OCR-A font. Scan the Modulo 10 Check Character symbol. Then scan the Enter OCR Template symbol, and scan the d from the OCR Programming Chart seven times, and scan the c once.
OCR Programming 8-12 PowerScan ® 7000 2D OCR User-Defined Check Character Y ou can customize the check character calculation to suit your applica- tion. Each character of the check character alphabet can be programmed in its proper order . The number of characters you enter determines the modulo value for the calculation.
OCR User-Defined Check Character Product Reference Guide 8-13 After you enter all the desired hex v alues, scan the Save bar code on the Programming Chart on page B-5 of this manual. Weighting Options By default, the check character computation is unw eighted.
OCR Programming 8-14 PowerScan ® 7000 2D 2-1-2-1 Weighted Modulo 10 Check Character S tarting with the check character and working backward through the message, the imager applies a multiplier of 1, then 2, then 1, then 2, and so on. When the result of the multiplication is greater than 9, add both digits to the running sum.
OCR ISBN Application Example Product Reference Guide 8-15 OCR ISBN Application Example One application of OCR is to read the ISBN characters typically encoded using the OCR-A or OCR-B font. This is especially useful when the ISBN number is not encoded in an EAN-13 bar code.
OCR Programming 8-16 PowerScan ® 7000 2D 4.) when the modulo 11 check character “0123456789X” is pro- grammed. Please note that all these commands can be combined into a single serial programming command: OCRENA2,TMP”ISBNggggggggggggctCdddd hdddEtCdddd hddddE”,GPG”0123456789-”,GPH”P”,CHK”0123456789X”.
OCR Template Codes Product Reference Guide 8-17 Exit Selections Sav e OCR T emplate Discard OCR T emplate.
OCR Programming 8-18 PowerScan ® 7000 2D NOTES.
Product Reference Guide 9-1 Chapter 9 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. befor e the decoded symbology . (See the Symbology Chart on page A-1 ) for the single character code that identifies each symbology .
Utilities 9-2 PowerScan ® 7000 2D Resetting the Standard Product Defaults If you ar en ’ t sure what programming options ar e in your imager , or you ’ ve changed some options and want the standar d product default set- tings restored, scan the S tandar d Pr oduct Default Settings bar code belo w .
Power Image Configurator Product Reference Guide 9-3 T o see displayed results, Microsoft ® Notepad, a wor d processor/editing program, or P owerView ( page 9-6 ) is recommended. F or additional information on interpreting your r ead results, please contact Datalogic using the website address listed on the back page of this manual.
Utilities 9-4 PowerScan ® 7000 2D Temporary Configuration Using Configura- tor F or quick download communication configuration, scan the appr opriate P ower Image Configurator bar code for your interface below to tempo- rarily configure the imager for P ower Image Configurator settings.
Power Image Configurator Product Reference Guide 9-5 8. U nzip and extract the .exe file. D ouble-click the .exe to install the software. F ollo w the screen prompts to install the P ower Image Configurator program.
Utilities 9-6 PowerScan ® 7000 2D NOTES.
Product Reference Guide 10-1 Chapter 10 Serial Programming Commands Serial Programming Commands The serial programming commands can be used in place of the program- ming bar codes. Both the serial commands and the programming bar codes will program the P owerScan 7000 2D.
Serial Programming Commands 10-2 PowerScan ® 7000 2D Menu Command Syntax M enu commands have the following syntax (spaces have been used for clarity only): P refix T ag S ubT ag {Data} [, S ubT ag {Data}] [; T ag SubT ag {Data}] […] St ora g e P refixThree ASCII characters: SYN M CR (ASCII 22,77,13).
Menu Command Syntax Product Reference Guide 10-3 Tag Field Usage When a query is used in place of a T ag field, the quer y applies to the entire set of commands av ailable for the particular storage table indicated by the S torage field of the command.
Serial Programming Commands 10-4 PowerScan ® 7000 2D When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.
Trigger Commands Product Reference Guide 10-5 This response indicates that the device ’ s Codabar Coding Enable (CBRENA) is set to 1, or on; the S tart/Stop Character (SSX) is set to 0, or D on ’ .
Serial Programming Commands 10-6 PowerScan ® 7000 2D Menu Commands Selection Setting * Indicates default Serial Command # Indicates a nume ric en try Pag e F actory Default Settings Default DEF AL T .
Menu Commands Product Reference Guide 10-7 Program K e yboard Country *U .S.A. KBDCTY0 2-3 Belgium KBDCTY1 2-3 Brazil KBDCTY16 2-3 Canada (F rench) KBDCTY18 2-3 Czechoslov akia KBDCTY15 2-3 Denmark KB.
Serial Programming Commands 10-8 PowerScan ® 7000 2D K eyboard Style *Regular KBDSTY0 2-5 Caps Lock KBDSTY1 2-5 Shift Lock KBDSTY2 2-5 Automatic Caps Loc k KBDSTY6 2-6 Auto Caps via Num Loc k KBDSTY7.
Menu Commands Product Reference Guide 10-9 W ord Length: Data Bits, Stop Bits, and P arity 7 Data, 1 Stop , P arity Even 232WRD3 2-9 7 Data, 1 Stop , P arity None 232WRD0 2-9 7 Data, 1 Stop , P arity .
Serial Programming Commands 10-10 PowerScan ® 7000 2D LED - Good Read Off BEPLED0 3-3 *On BEPLED1 3-3 Number of Beeps - Good Read *1 BEPRPT 3-3 Range 1 - 9 BEPRPT# 3-3 Reread Delay Shor t (500 ms) DL.
Menu Commands Product Reference Guide 10-11 LED P ower Le v el Off PWRLDC0 3-10 Low (50%) PWRLDC50 3-10 *High (100%) PWRLDC100 3-10 Illumination Lights *Lights On SCNLED1 3-11 Lights Off SCNLED0 3-11 .
Serial Programming Commands 10-12 PowerScan ® 7000 2D Require Output Sequence Required SEQ_EN2 3-21 On/Not Required SEQ_EN1 3-21 *Off SEQ_EN0 3-21 Multiple Symbols On SHO TGN1 3-22 *Off SHO TGN0 3-22.
Menu Commands Product Reference Guide 10-13 Interfunction Delay R ange 0 - 495 ms DL YFNC## 4-7 Intermessage Delay Range 0 - 495 ms DL YMSG## 4-8 Data Formatter Selections Data F or mat Edi- tor *Defa.
Serial Programming Commands 10-14 PowerScan ® 7000 2D Codabar Concate- nation *Off CBRCCT0 6-4 On CBRCCT1 6-4 Require CBRCCT2 6-4 Codabar Mes- sage Length Minimum (2 - 60) *4 CBRMIN## 6-5 Maximum (2 - 60) *60 CBRMAX## 6-5 Code 39 Default All Code 39 Settings C39DFT 6-5 Code 39 Off C39ENA0 6-5 *On C39ENA1 6-5 Code 39 Star t/ Stop Char .
Menu Commands Product Reference Guide 10-15 Interleaved 2 of 5 Check Digit * No Check Char . I25CK20 6-10 V alidate, But Don’t T ransmit I25CK21 6-10 V alidate, and T ransmit I25CK22 6-10 Interleave.
Serial Programming Commands 10-16 PowerScan ® 7000 2D Matrix 2 of 5 *Off X25ENA0 6-14 On X25ENA1 6-14 Matrix 2 of 5 Mes- sage Length Minimum (1 - 80) *4 X25MIN## 6-14 Maximum (1 - 80) *80 X25MAX## 6-.
Menu Commands Product Reference Guide 10-17 UPC-A Default All UPC-A Settings UP ADFT 6-19 UPC-A Off UP AENA0 6-19 *On UP AENA1 6-19 UPC-A Check Digit Off UP ACKX0 6-19 *On UP A CKX1 6-19 UPC-A Number .
Serial Programming Commands 10-18 PowerScan ® 7000 2D UPC-E0 Check Digit Off UPECKX0 6-22 *On UPECKX1 6-22 UPC-E0 Number System Off UPENSX0 6-23 *On UPENSX1 6-23 UPC-E0 Addenda 2 Digit Addenda On UPE.
Menu Commands Product Reference Guide 10-19 EAN/JAN-8 Off EA8ENA0 6-26 *On EA8ENA1 6-26 EAN/JAN-8 Chec k Digit Off EA8CKX0 6-26 *On EA8CKX1 6-26 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 6-26 2 D.
Serial Programming Commands 10-20 PowerScan ® 7000 2D RSS Limited Default All RSS-14 Limited Settings RSLDFT 6-30 RSS Limited Off RSLENA0 6-30 *On RSLENA1 6-30 RSS Expanded Default All RSS-14 Expanded Settings RSEDFT 6-31 RSS Expanded Off RSEENA0 6-31 *On RSEENA1 6-31 RSS Expanded Msg.
Menu Commands Product Reference Guide 10-21 Code 16K Msg. Length Minimum (0 - 160) *1 16KMIN### 6-34 Maximum (0 - 160) *160 16KMAX### 6-34 Code 49 Default All Code 49 Settings C49DFT 6-35 Code 49 Off C49ENA0 6-35 *On C49ENA1 6-35 Code 49 Msg.
Serial Programming Commands 10-22 PowerScan ® 7000 2D P ostnet Chec k Digit T ransmit NETCKX1 6-40 *Don’t T ransmit NETCKX0 6-40 Planet Code On PLNENA1 6-41 *Off PLNENA0 6-41 Planet Code Check Digi.
Menu Commands Product Reference Guide 10-23 QR Code Msg. Length Minimum (1-3500) *1 QRCMIN 6-46 Maximum (1-3500) *3500 QRCMAX 6-46 Data Matrix Default All Data Matrix Set- tings IDMDFT 6-46 Data Matrix *On IDMENA1 6-47 Off IDMENA0 6-47 Data Matrix Msg.
Serial Programming Commands 10-24 PowerScan ® 7000 2D Imaging Default Commands Image Snap Default all Imaging Com- mands IMGDFT 7-1 Imaging Style - Decoding SNPSTY0 7-2 *Imaging Style - Photo SNPSTY1.
Menu Commands Product Reference Guide 10-25 Image Ship *Infinity Filter - Off IMGINF0 7-4 Infinity Filter - On IMGINF1 7-4 *Compensation Off IMGCOR0 7-4 Compensation On IMGCOR1 7-4 *Pix el Depth - 8 b.
Serial Programming Commands 10-26 PowerScan ® 7000 2D Image Ship (con- tinued) Image Crop - Bottom (0-480) *479 IMGWNB### 7-7 Image Crop - Margin (1-238) *0 IMGMAR### 7-7 Protocol - None (raw) IMGXFR.
Menu Commands Product Reference Guide 10-27 OCR Check Char- acter OCR Mod. 10 Check Char . “OCRCHK0123 456789” 8-11 OCR Mod. 36 Check Char . “OCRCHK0123 456789ABCDE FGHIJKLM- NOPQRSTU- VWXYZ” 8-11 OCR User-Defined Check Char . OCRCHK 8-12 3-1-3-1 Weighted Mod.
Serial Programming Commands 10-28 PowerScan ® 7000 2D NOTES.
Product Reference Guide 11-1 Chapter 11 Product Specifications Imager Product Specifications Parameter Specification Dimensions (T ypical): Height 7.5”/190 mm Length 4.
Product Specifications 11-2 PowerScan ® 7000 2D P ower Supply: Noise Rejection Maximum 100mV peak to peak, 10 to 100 kHz Mechanical Shock 50 drops from 6.
Standard Cable Pinouts (Primary Interface Cables) Product Reference Guide 11-3 Standard Cable Pinouts (Primary Interface Cables) Serial Output 10 Pin RJ41 Modular Plug connects to the imager handle 1 .
Product Specifications 11-4 PowerScan ® 7000 2D Standard Cable Pinouts USB UKBW 10 Pin Modular Plug connects to the imager handle 1 2 3 4D - 5 6D + 7 8 VBUS_VIN 9G N D 10 Cable Select 10 Pin Modular .
User’s Guide A-1 Appendix A Symbologies Symbology Chart Symbology AIM ID P ossible AIM ID Modifiers ( m ) Code ID (hex) All Symbologies (0x99) Austr alian P ost ]X0 A (0x41) Aztec Code ]z m 0-9, A-C.
A-2 PowerScan ® 7000 2D EAN-13 ]E 0 d (0x64) EAN-8 ]E4 D (0x44) EAN•UCC Composite ]e m 0-3 y (0x79) EAN-13 with Extended Coupon Code ]E3 d (0x64) Interleaved 2 of 5 ]l m 0, 1, 3 e (0x65) Japanese P.
Symbology Chart User’s Guide A-3 * Only av ailable b y special order . Ref er to Data Editing on page 4-1 and Data Formatting on page 5-1 for information about using Code ID and AIM ID.
A-4 PowerScan ® 7000 2D ASCII Conversion Chart (Code Page 1252 ) Dec Hex Char Dec Hex Char Dec He x Char Dec Hex Char 0 00 NUL 1 20 2 40 @ 3 60 ‘ 4 01 SOH 5 21 ! 6 41 A 7 61 a 8 02 STX 9 22 “ 10 .
ASCII Conversion Chart (Code Page 1252) User’s Guide A-5 84 15 NAK 85 35 5 86 55 U 87 75 u 88 16 SYN 89 36 6 90 56 V 91 76 v 92 17 ETB 93 37 7 94 57 W 95 77 w 96 18 CAN 97 38 8 98 58 X 99 78 x 100 1.
A-6 PowerScan ® 7000 2D 168 8A Š 169 AA 170 CA Ê 171 EA ê 172 8B ‹ 173 AB « 174 CB Ë 175 EB ë 176 8C Œ 177 AC ¬ 178 CC Ì 179 EC ì 180 8D 181 AD - 182 CD Í 183 ED í 184 8E Ž 185 AE ® 1.
Code Page Mapping of Printed Bar Codes User’s Guide A-7 Code Page Mapping of Printed Bar Codes Code pages define the mapping of character codes to characters.
A-8 PowerScan ® 7000 2D NOTES.
Product Reference Guide B-1 Appendix B Sample Symbols 0 123456 7890 1234567890 Code 128 9 780330 290951 BC321 123456-9$ 123456 UPC-A Code 128 Code 39 Code 93 Interleaved 2 of 5 EAN-13 Code 2 of 5 A135.
B-2 PowerScan ® 7000 2D Sample Symbols 6543210 (01)00123456789012 Code 49 Car Registration Zip Code 1234567890 Test Symbol Numbers Matrix 2 of 5 PDF417 RSS-14 P ostnet QR Code Data Matrix.
Product Reference Guide B-3 Sample Symbols Package Label Test Message Test Message Aztec MaxiCode Micro PDF417 OCR-B with Modulo 10 check character OCR-A with Modulo 36 check character.
B-4 PowerScan ® 7000 2D OCR Programming Chart a e d g c h t l Discard Sav e r.
Programming Chart Product Reference Guide B-5 Programming Chart A C B F E D 1 0 2 3.
B-6 PowerScan ® 7000 2D Programming Chart 6 7 5 4 8 9 Sav e Discard NO TE If you make an err or while scanning the letters or digits (before scanning Save), scan Discar d, scan the correct letters or digits, and Save again.
Programming Chart Product Reference Guide B-7 NOTES.
B-8 PowerScan ® 7000 2D NOTES.
.
©2007 Datalogic Scanning, Inc. R44-2769 (Rev . A) 4/07 Aus t r al i a Datalogic Scanning Pty Ltd Nor th Ryde, A ustralia T elephone: [61] (2) 9870 3200 F ax: [61] (2) 9878 8688 France and Benelux Datalogic Scanning Sarl LES ULIS Cedex, F rance T elephone: [33].
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Datalogic Scanning 7000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Datalogic Scanning 7000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Datalogic Scanning 7000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Datalogic Scanning 7000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Datalogic Scanning 7000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Datalogic Scanning 7000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Datalogic Scanning 7000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Datalogic Scanning 7000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
