Manuale d’uso / di manutenzione del prodotto DSC-34W70N del fabbricante Daewoo
Vai alla pagina of 61
USER MANUAL HDTV Monitor DSC-34W70N.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
IMPORT ANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIP- MENT AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE TV RECEIVER. 1 Read all of these instructions. 2 Save these instructions for later use.
13 An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
CONTENTS 5 PREP ARA TION •CONNECTING ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 •NAME OF EACH P ART . . . . . . . . . . . . . . . . . . . . . . .
CON NECTING ANTENNA NOTE: Bad picture reception could often be caused by bad antenna connection. Be sure to check the antenna direction, its height, etc.
NAME OF EACH P ART 7 Front and Side of TV set •The buttons installed on the front of the TV set is functioning as same as those on the Remote Control. 1. Timer Indicator Lights up red when you have set the HDTV Monitor’s automatic timers. 2. Power Indicator Lights up green when you have turned the HDTV Monitor on.
8 On the right side panel of the HDTV Monitor , you will find the V ideo 3 inputs and Headphone jack. These are provided to connect a camcorder or other video equipment without reaching around to the rear panel. HEADPHONE : provides a connection for headphones.
REMOTE CONTROL BUTT ONS 9 L L Caution! • Do not drop. • Avoid moisture, heat, and dust. L L Installation of batteries: • Push to open the cover of the Remote Control. • Set the batteries in the battery (cell), compartment after checking the electrodes(+,–), and then, shut the cover.
10 Under the Cover of Remote Control To use the buttons under the cover Note: •When batteries are low, the Remote Control may not work. Change them immediately when they get weak. •Be sure to use two 1.5V size AAA batteries. •Do not use new batteries together with the old ones.
T O W A TCH TV PROGRAM 11 Buttons on the front of the TV set have the same functions as those of the REMOTE CONTROL. B Press two number buttons of the Remote Control to select a channel directly.
12 1.Press the “TV POWER”button. •The TV screen will illuminate, and the power indicator lamp will light up green. 2.Press the “CHANNEL” buttons. •Press the “CHANNEL x / y ” or number buttons to select the channel you want. Ex) Ch 7 3.
13 1.Press “MENU” button. •The main menu will appear . 2.Select “Setup”. •Move the cursor to the “Setup ” menu by using “ VOLUME C / B ” buttons. •Select “Setup ” sub-menu by using “ CHANNEL x ” button. 3.Select Auto Program by using “ CHANNEL x x / y y ” buttons.
14 4.Press “ VOLUME C / B ” buttons. Automatic Channel Memory function (Auto Program) starts. •Checking from channel 2 to channel 69,(Cable1~125) this function automatically memorizes only those channels which are actually broadcasting. •When “MENU” button is pressed during the setup process, the setup operation quits.
15 1.Select a channel. •Select a channel by pressing number buttons. Ex) Ch 13 2.Choose to add or erase from memory . •Press the “ADD/ERASE” Button. •Whenever this button is pressed, the color of channel sign changes from green to red, and vice versa.
Press “WIDE” button. •When “WIDE” button is pressed, the aspect ratio of the screen shifts cyclically as follows : (16:9) (4:3) (Panorama) (16:9) 16 1.Press “TV/CA TV” button. •The reception mode shifts from “AIR” to “CABLE”. 2.
17 1 .Connect the video cable to the VIDEO socket at the back or the side of TV set, and press “TV/VIDEO” button on the remote control. •The screen changes to video mode as follows: •Whenever this button is pressed, the screen shifts in sequence : TV Video1 Video2 Video3 DVD TV W atching V ideo Programs Video1 2 .
1.Press “PIP” button once. •Single PIP appears on the screen. ADJUSTING TWO PROGRAM WINDOWS 18 2.Press “PIP” button once more. •The operating program window becomes the main window and moves to the left side of the screen; an auxiliary window appears on the right side at the same time.
V ARIOUS FUNCTIONS OF SIMUL T ANEOUS WINDOW MODE 19 2.Select “Funtion” button. •Move the cursor to the “Funtion” menu by using “VOLUME C / B ” buttons. •Select “Funtion” Sub-menu by using “CHANNEL x ” button. 3.Select “PIP”.
20 4. Press “ VOLUME C / B ” buttons, and select the window mode you want. •When the “VOLUME C / B ” buttons are pressed, the screen shifts in the following order: Single PIP Picture T win picture Multi-picture(4) Off, and vice versa.
21 1.Press “PIP” button. •Y ou can enjoy two window programs simultaneously . •The same channel or child lock channel can not be operated in both windows of the screen.
22 4.Press “PIP” button again. •PIP mode changes to twin windows. 5. Press “PIP” button again, and the auxiliary window disappears. •Whenever the “PIP” button is pressed, the screen mo.
23 1.Press “SEARCH” button. •Four windows appear on the screen. Memorized channels are connected one-by- one to each window in sequence; thus it is easy to check the contents of the programs on air . •Whenever the “SEARCH” button is pressed, the screen changes cyclically as follow: •Press “SEARCH” button.
24 1.Press “POSITION” button. •Display auxiliary windows on the screen by pressing “PIP” buttons. •Press “POSITION” button. Every time it is pressed, the locations of auxiliary windows.
25 Press “SW AP” button. •View the auxiliary window by pressing “PIP” button. •Press “SW AP” button. Every time it is pressed, the mode of the main and that of the auxiliary windows will swap locations as follows: This function also operates in T win Windows mode.
26 Changing Window Modes is also Possible in Multi-W indows Search. • The window with “ B ” sign not only becomes the new main window , but also the auxiliary window . Air 7 Mono 9 11 13 Air 9 Mono 9 11 13 B B Air 9 Mono 7 11 13 B Making Pause Auxiliary Windows.
•The following picture will appear on the screen. 1. Press “MENU” button. •The screen appears as follows: ADJUSTING VOLUME OF AN AUXILIAR Y WINDOW 27 L Sound of either the main window or an auxiliary window is available through headphones. L Volume control of an auxiliary window is possible only with headphones.
OPEN FUNCTION MENU 28 1. Press “MENU” button. •The screen appears as shown: •The following picture will appear on the screen: 3. Press “CHANNEL x x / y y ” buttons.
ADJUSTING THE PICTURE 29 1. Press “AUT O PICTURE” button. •The following pictures appear on the screen in sequence, and the picture adjustment state is changed. <For pressing “AUTO PICTURE” button once> <For pressing “AUTO PICTURE” button many times> 2.
30 1. Press “MENU” button. •The screen appears as follows : 2. Select “Picture” by using “CHANNEL x x ” button. •Move the cursor to the “Picture” menu by using “CHANNEL x ” button. 3. Press “CHANNEL x x / y y ” buttons. •When “Picture” mode is selected, its sub-menu appears on the screen.
31 1.Press “MENU” button. •Then the screen appears as follows: 2.Select “Picture” by using “CHANNEL x x ” button. •“Picture” mode is selected, and its sub-menu appears.
4. Adjust “Brightness” by using “VOLUME C C / B B ” buttons •Press “VOLUME B ” button for the Brightness to in crease. •Press “VOLUME C ” button for the Brightness to decrease. Brightness 32 Contrast 60 Sharpness 32 Color 32 Tint 32:32 Picture NR Off 32 3.
ADJUSTING THE SOUND 33 1. Press “MENU” button. •Then, the screen appears as follows : 2. Select “Sound” menu by using “VOLUME C C / B B ” buttons. •Move the cursor to the “Sound” menu by using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button.
34 4. Select Range of Sound by using “VOLUME C C / B B ” buttons. •“CHANNEL x ” strengthens the selected range of sound. •“CHANNEL y ” weakens the range of sound. •Signal bar (-) moves up and down showing the selected sound range. •The selected range of sound looks pale blue, and the range not selected looks white.
1.Press “MTS” button. •Whenever this button is pressed the mode status shifts in the following sequence: Mono Stereo SAP . •Press “RECALL” button on the Remote Control to check the program transmission mode. •When the program transmission is in stereo mode, select “Stereo” to receive the stereo sound.
3. Press “CHANNEL x x / y y ” buttons. •“Function” mode is selected, and the sub-menu appears. •Press “CHANNEL x / y ” buttons until the blue bar indicates “T imer”. AUT OMA TIC POWER ON/OFF 36 1. Press “MENU” button. •The screen appears as shown : 2.
37 4. Set up the Curent T ime. •Press “VOLUME C / B ” buttons, and the screen appears as shown in the left figure: •Press “CHANNEL x / y ” buttons, and the letters “AM 1:00” will turn in blue. •Set up the present time by using “VOLUME C / B ” buttons.
38 1. Press “MENU” button. •Then, the screen will appear as follows : 2. Select “Function” by using “VOLUME C C / B B ” buttons. •Move the cursor to the “Function” menu by using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button.
5. Set up “On T imer”. •Press “CHANNEL x / y ” buttons, and the letters AM - - : - - will turn blue. •Set up “On T imer” by using “VOLUME C / B ” buttons •Keep pressing the “VOLUME C / B ” buttons, then, the set up time will continue to change by unit of one minute until the button is released.
40 7. Set up the “Off Timer”. •Press “CHANNEL x / y ” buttons, and the letters “AM - - : - -” will turn blue. •Set up “Of f T imer” by using “VOLUME C / B ” buttons. •Keep pressing the “VOLUME C / B ” buttons, then the set up time will continue to change by unit of one minute until the button is released.
3.Press “CHANNEL x x / y y ” buttons. •Select language (as shown) highlighted with the blue function indicator bar . SPECIAL FUNCTIONS 41 1.Press “MENU” button. •The main menu will appear as shown in this example: 2.Select “Function”. •Move the cursor to the “Function” menu using “VOLUME C / B ” buttons.
4. Select the language using “VOLUME C C / B B ” buttons. •Press this button, and the On-Screen language changes in the following order : English Francais Español English 42 5.Press “MENU” button. •Press this button once, and the main menu window will appear .
43 1.Press “MENU” button. •The main menu will appear . 2.Select “Set Up”. •Move the cursor to the “Set Up” menu using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button to select set up, and the sub menu will appear . 3.Press “CHANNEL x x / y y ” buttons.
44 4.Select “Fine” to fine tune. •Highlight “Fine”. •Press “VOLUME C / B ” buttons to fine the channel. •Keep pressing “VOLUME C / B ” buttons until the channel is as clear as possible. •T o fine tune another channel, first, select the channel, then repeat the steps above.
45 1.Press “MENU” button. •The main menu will appear . 2.Select “Function” by using “VOLUME C C / B B ” buttons. •Move the cursor to the “Function” menu using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button to select function, and the sub menu will appear .
46 4.Select an appropriate mode. •Press “VOLUME B ” button, and the mode will change in the following order: Off CC1 CC2 CC3 CC4 Off 5.Press “MENU” button twice. •Press this button once, and the menu window will appear . •Press it again, and you will get the previous status of the menu window .
47 1.Press “MENU” button. •The main menu will appear . 2.Select “Function”. •Move the cursor to the “Function” menu using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button to select “Function”, and the sub menu will appear .
4.Enter your password. •Use the number buttons(0-9) to enter your password. Note, if this is the your time using the “Parental Control” menu, be certain to remember it, after entering your password, or keep a written copy stored as you would with any confidential info.
• The “No Rating” item toggles between “Unblock” and “Block”. This item determines whether or not to block the programs which are not rated by “Movie Ratings” and “TV Guidelines”. Use “VOL C / B ” buttons to change the settings.
PRO LOGIC SETTINGS 50 1.Press “MENU” button. •The main menu will appear . 2.Select “Special”. •Move the cursor to the “Special”, menu using “VOLUME C / B ” buttons. •Press “CHANNEL x ” button to select “Special”, and the sub menu will appear .
51 1. Press “MENU” button. • The main menu will appear . 2. Select “Special”. • Move the cursor to the “Special” menu using “VOLUME C / B ” buttons. • Press “CHANNEL x ” button. 3. Select “Tilt” • Press “CHANNEL x / y ” buttons to select “T ilt” 4.
52 DTV Input Selection 1.Press “MENU” button. •The main menu will appear . Move Sel. Exit Picture 2.Select “Special”. •Move the cursor to the “Special” menu using “VOLUME C / B ” buttons. • Press “CHANNEL V ” button to select “Special”, and the sub menu will appear .
53 CONNECTING EQUIPMENTS VIDEO INPUT 1 ANTENNA IN S-VIDEO VIDEO AUDIO L R Y Pb Pr L R VIDEO AUDIO L R VIDEO AUDIO Y Cb Cr VIDEO MONITOR OUTPUT SURROUND OUTPUT L W R AUDIO L R VIDEO INPUT 2 DTV INPUT D.
54 VIDEO INPUT 1 ANTENNA IN S-VIDEO VIDEO AUDIO L R Y Pb Pr L R VIDEO AUDIO L R VIDEO AUDIO Y Cb Cr VIDEO MONITOR OUTPUT SURROUND OUTPUT L W R AUDIO L R VIDEO INPUT 2 DTV INPUT DVD INPUT Y Pb Pr L R HD Component Output T o connect a HD component, follow the diagram below .
55 Subwoofer Left Rear Speaker Right Rear Speaker VIDEO INPUT 1 ANTENNA IN S-VIDEO VIDEO AUDIO L R Y Pb Pr L R VIDEO AUDIO L R VIDEO AUDIO Y Cb Cr VIDEO MONITOR OUTPUT SURROUND OUTPUT L W R AUDIO L R .
56 PROGRAMMING THE REMOTE CONTROL The HDTV Monitor is remote control is pre-programmed to operate your HDTV Monitor . However , you can also program the HDTV Monitor ’s remote control to operate other components, such as Cable TV BOX, or VCR. 1. Confirm that the external component is plugged in and turned off.
ABC 004 006 007 041 POST NEWS WEEK 019 044 048 055 PRUCER 094 ANTRONIX 017 PTS 014 050 070 071 ARCHER 008 010 017 027 095 096 CABLE ST AR 029 PULSAR 054 CENTURION 084 RCA 049 CENTUR Y 010 REGAL 051 05.
58 VCR Brand Code ADMIRAL 164 AIW A 033 AKAI 017 040 042 100 101 1 15 158 AMPRO 068 ANAM 030 032 081 AUDIO DYNAMICS 013 023 037 040 166 BROKSONIC 034 036 102 CALIFORNIA AUDIO 123 CANON 027 030 032 CAP.
59 TROUBLESHOOTING T r o u b l e s h o o t i n g: Neither picture nor sound: •Is power code plugged in? •Press power button on the front of TV. •If the red power light is on, press the remote control power button. Red power light should be green.
Rear RF Antenna Input NTSC A/V In (Video/L/R) 2each NTSC A/V In (S-Video/V ideo/L/R) 1each NTSC A/V Monitor Out (Video/L/R) 1each HD Component In (Y/Pb/Pr/L/R) 1each DVD Component In (Y/Cb/Cr/L/R) 1ea.
P/N:48586120E105-R1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Daewoo DSC-34W70N è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Daewoo DSC-34W70N - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Daewoo DSC-34W70N imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Daewoo DSC-34W70N ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Daewoo DSC-34W70N, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Daewoo DSC-34W70N.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Daewoo DSC-34W70N. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Daewoo DSC-34W70N insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
