Manuale d’uso / di manutenzione del prodotto RS-850 del fabbricante Crimestopper Security Products
Vai alla pagina of 16
RS-850 Remote Engine Starting System INSTALLATION INSTRUCTIONS PRE-INSTALLATION CONSIDERATIONS To ease and reduce installation time, we suggest you R EAD THIS MANUAL and consider the following points .
TABLE OF CONTENTS Pre-Installation Considerations…………...……...………………………………………………………………Front Cover Cautions & Warnings…….…………..….……..…..……………………………………………………………….
WIRING 2 PIN PLUG-PROGRAM/OVERRIDE SWITCH: This switch is used for programming features, transmitters, and valet mode. 2 PIN PLUG-(OPTIONAL) LED: The LED is used as an indicator for Valet, Programming, and for use as security deterrent with the optional ANTI- GRIND/STARTER DISABLE feature installed.
WIRING PIN 4: YELLOW/BLACK: (-) ANTI-GRIND/STARTER KILL OUTPUT (OPTIONAL) Use this wire for the negative side of the Anti-Grind/Starter Dis able relay. It can also be used as a sensor disable circuit for a host alarm. This output activates whenever a remote start is requested, and when the vehicle is remotely locked with the transmitter.
WIRING PIN 8: PINK: (+12V) DIESEL GLOW PLUG INPUT Connect Pink wire to indicator circuit that shows +12 volts while the “WAIT TO START LAMP ” is on. When this wire is used, the system will wait until light turns off before attempti ng a remote start.
IGNITION SWITCH WIRING PA R K I N G LIGHTS FUSE RED WH IT E 30A FUSE RED +10A M AX. 30A + - BROWN PINK FUEL ENGI NE BA TTER Y PUMP ECU GRA Y + ST ARTER - COI L IGN 1 AC C Heat/A C Diag ram Not to Sca le. For i llustra tion purp oses only . Y our veh icle may differ .
POWER DOOR LOCK WIRING PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems.
BASIC DOOR LOCK DIAGRAMS NEGA TIVE TRIGGER DOO RLOCK WIRING POSITIVE TRIGGER DO ORLOCK WI RING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC T O RY FAC T O RY L L POWE.
“SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “S mart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each time a remote start is requested.
TACH (RPM) REFERENCE MODE / TACH FINDER MODE / TACH PROGRAMMING Tach Reference Mode provides reliable remote start ing performance though engine speed sensing. When using Tach Reference Mode, the Red/White wire is used for Tach signal [Engine R PM] input.
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4 different transmitter codes. 1. Open Hood. (Ground Gray wire.) 2. Turn key to the ON position. 3. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times.
OPTION PROGRAMMING IMPROVED: Now you can program multiple options in one sessi on if you start with the lowest option and continue on to higher options [if needed] without repeating the steps #1-3.
OPTION PROGRAMMING OPTION DESCRIPTIONS: 1. NOT USED: No Option 2. Door Lock Pulse Time: Controls the amount of time for lock/unlock pulse. The standard setting is 0.75 for most vehicles. A 3 sec. setting is required for 1980’s/90’s European Vacuum or Pneumatic door lock systems.
REMOTE START TROUBLESHOOTING “Before You Call Section” UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit is in Valet mode. Turn IGN ON, press and hol d valet/programming button for about 4 seconds until LED goes out. The unit is now out of valet mode and should perform a remote start.
TRAN SMISSION PROGRAM/ OVERRI DE PA R K I N G LIGHTS SW ITCH ECU RS-850 ANT ENNA / RECEIVER PLUG LED COIL + - (-) UNLOCK OUT PUT +12 V FO R RELA YS 12A MAX.
ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Crimestopper Security Products RS-850 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Crimestopper Security Products RS-850 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Crimestopper Security Products RS-850 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Crimestopper Security Products RS-850 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Crimestopper Security Products RS-850, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Crimestopper Security Products RS-850.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Crimestopper Security Products RS-850. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Crimestopper Security Products RS-850 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
