Manuale d’uso / di manutenzione del prodotto CS-2008PC del fabbricante Crimestopper Security Products
Vai alla pagina of 19
CS-2008PC SecurLinc™ ADVANCED REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS *NOTE: There are several features of the CS-2008PC system that can only be accessed and/or program.
TABLE OF CONTENTS Pre-Installation Cautions & Warnings…….…………………………………………………………..………………1 Control Module & Component M ounting…………………..……………………….……………………….
COMPONENT MOUNTING SIREN: Mount the siren under the hood to an inner fender-well, wheel-well, or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black to the body metal near the siren or you can use one of the siren’s mounting screws for a ground.
WIRING PIN 12: ORANGE WIRE: NEGATIVE ARMED OUTPUT – Starter Disable (500mA Ground, Optional) This wire becomes a (-) Ground output when system is armed. This output can be used for optional accessories such as window roll up modules, scanner LED’s, voice modules, etc.
SYSTEM WIRING DIAGRAM #1.
SYSTEM WIRING DIAGRAM #2.
SHOCK SENSOR DUAL ADJUST Smart Sense™ Shock Sensor: GREEN RED Pre-Warn Tr i g g e r The supplied dual stage / dual adjust shock sensor does not require any additional wiring. Just mount the sensor, plug in the “Sensor #1” input plug on the 2008PC harness and adjust to the desired levels of sensitivity for pre-warn and shock sensor violations.
POWER DOOR LOCK WIRING GREEN: (-) LOCK / (+) UNLOCK BLUE: (-) UNLOCK / (+) LOCK COMMON DOOR LOCK TYPES: (SEE FOR DESCRIPTIONS) Negative Trigger (-): Many Imports, Late Model Ford & General Motors .
POWER DOOR LOCK WIRING NEGA TIVE TRIGGER DOO RLOCK WIRING POSITIVE TRIGGER DO ORLOCK W IRING GREEN GREEN BLUE BLUE DIO DES FA C T O R Y FA C T O R Y L L LOCK LOCK POW ER POW ER LOCKING LOCKING UL UL R.
REMOTE TRANSMITTER PROGRAMMING 1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3 rd time. (ON/OFF, ON/OFF, ON) You should hear (3) chirps. 2. Press the Program/Override Button for 5 seconds and you should hear 5 chirps and LED comes on solid.
OPTION PROGRAMMING TABLE PROGRAMM ING OPTIONS CHART * = Default (Column 1) Option # Option Description BUTTON 1* LOCK BUTTON 2 UNLOCK BUTTON 3 TRUNK 1. Passive Arming/ Hands-free mode Passive OFF* Hands-free OFF* Passive Arming Enable Hands-free Mode Enable 2.
OPTION DESCRIPTIONS 2. ACTIVE RE-ARMING / HANDS-FREE IMMOBILIZER This option controls the Active Re-arming feature and the Hands-free immobilizer. There are 3 selections: Button 1 (Lock) = Both Active Re-arming and Hands-free immobilizer are OFF. Button 2 (Unlock) = Enable Active Re-arming.
OPTION PROGRAMMING 12. HORN OUTPUT / CARJACK WITH HANDS-FREE REMOTE (2 FEATURES) This option controls whether the system’s Factory Horn output AND full-time Carjack operation. There are 3 selections: Button 1 (Lock) = Horn Output Pulses on trigger and Full-time Carjack are disabled.
OPTION RESET TO RESTORE ALL PROGRAMMABLE OPTIONS TO DEFAULT VALUES (*): 1. Turn the Ignition ON and press the Program/Override button 5 times. The siren will chirp 3 times indicating you are in programming mode. 2. Press the #3 Button (Trunk Symbol) on the Transmitter.
“HANDS FREE” REMOTE CONTROL (OPTIONAL) This 2008PC system is compatible with an optional “Hands-free” remote transmitters (not included in kit). The “Hands-free” remote transmitter adds two important features. • Convenient “hands-free” operation and additional security.
HANDS-FREE PROGRAMMING & SETUP NOTE: PASSIVE ARMING AND PASSIVE LOCKING M UST BE ENABLED ALONG WITH THE HANDS- FREE MODE. ENABLE HANDS FREE MODE: 1. Follow steps to enter Option Programming mode. (See page 7) 2. Press program button 1 time to get to option #1.
5-BUTTON REMOTE OPERATION: 5-Button One-Way Remote Functions: PA N I C BUTTON 1 BUTTON 3 BUTTON 2 BUTTON 4 BUTTON 5 (ON SIDE) BANK #1 (Directly Press Buttons) Button 1: Arm / Lock Button 2: Disarm / U.
ALARM OPERATION PANIC FEATURE: In the event of an emergency situation or to attract att ention to your vehicle, press and hold Button #4 (Panic). The Siren will sound and lights will flash for 30 seconds.
ALARM OPERATION DOME LIGHT ILLUMINATION: (Optional) This feature turns on the vehicle’s dome light upon disarm for 30 seconds or until the key is inserted and turned on. This will provide illuminated entry to your vehicle at night or in dimly lit areas for safety and security.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Crimestopper Security Products CS-2008PC è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Crimestopper Security Products CS-2008PC - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Crimestopper Security Products CS-2008PC imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Crimestopper Security Products CS-2008PC ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Crimestopper Security Products CS-2008PC, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Crimestopper Security Products CS-2008PC.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Crimestopper Security Products CS-2008PC. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Crimestopper Security Products CS-2008PC insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
