Manuale d’uso / di manutenzione del prodotto 79989 del fabbricante Craftsman
Vai alla pagina of 21
OWNER'S MANUAL MODEL NOS. 247.799891 247.799892 Caution: Readand Follow All SafetyRules and Instructions Before Operating This Equipment CRRFTSMRN 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER-SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO.
SAFETY RULES _ WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TRAINING • Read this owner's manual carefully in its entirety before attempting to assemble or operate this machine.
CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder. It has been designed, engi- neered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily rem- edy, please contact your nearest Sears Service Center/ Department in the United States.
TABLE OF CONTENTS SAFETY RULES ......................................................... 2 PRODUCT SPECIFICATIONS ................................... 3 MAINTENANCE AGREEMENT .................................. 3 CUSTOMER RESPONSIBILITIES ..............
ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASO- LINE or OIL. After assembly, see operation section of this manual for proper fuel and engine oil recommen- dations. NOTE: To determine right and left hand sides of your chipper-shredder, stand behind and face the hopper (engine is at the front of the unit).
OPERATION KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Compare the illustrations with your chipper-shredder to familiarize yourself with the location of various controls and adjustments.
TO STOP ENGINE • Move throttle control lever to OFF position. See fig- ure 4. • Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. No Larger 1/2" Diameter (Recommended) Or 1" Diameter (Maximum) Hopper Assembly Tt Control FIGURE 4.
GAS AND OIL FILL-UP OIL Only use high quality detergent oil rated with API ser- vice classification SG. Select the oil's viscosity grade according to your expected operating temperature. Colder _ 32°F m Warmer NOTE: Although multi-viscosity oils (5W30, 10W30, etc.
• Attach spark plug wire and rubber boot to spark plug if necessary. See figure 8. • Place the throttle control lever in FAST position. See figure 9.
GENERAL RECOMMENDATIONS WARNING: ALWAYS STOP THE ENGINE AND DISCONNECT THE SPARK PLUG WIRE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. • Periodically check all fasteners and be sure they are tight. • Follow the Maintenance Schedule on previous page.
WARNING: PERIODICALLY CLEAN MUF- FLER AREA TO REMOVE ALL GRASS, DIRT AND COMBUSTIBLE DEBRIS. CLEANING • The chipper-shredder may be cleaned by running water from a hose through the hopper assembly and chipper chute with the engine running. Allow the chipper-shredder to dry thoroughly.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fueltankor stor- age container. Always follow the mix ratiofoundon stabilizer container. Runengine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor.
Replace or sharpen blades. If sharpening, make cer- tain to remove an equal amount from each blade. Reassemble in reverse order. Make certain blades are reassembled with the sharp edge facing the direction shown in figure 19 (sharp edge is assembled toward the slotted opening in the impeller assembly).
The carburetor may need re-adjusting if engine lacks power or does not idle properly. If adjustments are needed, proceed as follows. • Close needle valve (see figure 17) clockwise (F_) finger tight only. Forcing may cause damage. Then open 1-1/2 turns counterclockwise (f").
TROUBLE SHOOTING PROBLEM Engine fails to start Loss of power; operation erratic Engine overheats Too much vibration Unit does not discharge Rate of discharge slows considerably or composition of discharged material changes POSSIBLE CAUSE(S) • Fuel tank empty, or stale fuel.
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.799891 Repair Parts 247.799892 2O 8 Y9 / 41 13 39 11 7 22 23 6O 16 61 36.
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.799891 Repair Parts 247.799892 KEY NO. 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 30 PART NO.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 Repair Parts 135212-0140-01 REF. PART NO. NO. DESCRIPTION 55 494846 56 493824 57 262594 58 280406 59 396892 60 393152 65 94686 69 280973 69A.
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 Repair Parts 135212-0140-01 REF. PART DESCRIPTION NO, NO. 52 9O 95 96 97 108 118 124 127 127A 149 152 154 202 2O3 205 392 394 432 433 434 435 611 634 679 680 987 *-271936 495426 93499 223793 490048 491177 231533 94616 220352 223789 26336 260575 93527 262270 280720 231520 262328 .
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 Repair Pa rts 135212-0140-01 REF. PART NO. NO. DESCRIPTION 12 *270080 18 19 20 21 22 25 26 27 28 29 30 32 45 46 219 220 227 23O 562 592 614 .
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 Repair Parts REF. PART DESCRIPTION NO. NO. 1 395990 5 214040 7 *272157 8 495774 9 *27549 10 94621 11 66578 13 94221 14 94679 15 94387 16 495.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Craftsman 79989 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Craftsman 79989 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Craftsman 79989 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Craftsman 79989 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Craftsman 79989, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Craftsman 79989.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Craftsman 79989. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Craftsman 79989 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
