Manuale d’uso / di manutenzione del prodotto 2600 del fabbricante 3M
Vai alla pagina of 20
Instructions Fibrlok TM 2600 Series Multi-Fiber Optical Splice Issue 2, May 1993.
2.
3 Contents: 1.0 General .......................................................................................................................................................... 3 2.0 Preparation Kit ..................................................
4 .50" (1.27 cm) 1.50" (3.81 cm) .265" (.673 cm).
5 1.0 General The Fibrlok TM 2600 Series Multi-Fiber Optical Splicing System provides permanent mechanical splices for single-mode or multimode optical fibers with a nominal cladding diameter of 125 m.
6 3M Part # Construction Color 2634 12 fiber bonded or ribbonized Light Y ellow 2635 12 fiber A T&T ASR White 2637 10 fiber bonded or ribbonized Light Gray 2639 8 fiber bonded or ribbonized Light .
7 4.04 Connect the power cord from the AC adapter to the stripper handle. Plug the AC adapter into an electrical outlet. Note: An optional 6 volt battery and cord are available. 4.05 Arrange the fibers in the splice tray per tray instructions. T rim the ribbon end so that it extends approximately 3/4" (19 mm) beyond the center of the splice.
8 4.09 Release the handles. Clean the stripped fibers with alcohol and a lint free cloth. Inspect for broken fibers. Repeat steps 4.05 through 4.09 if necessary .
9 6.0 Cleaver Operation 6.01 The Alcoa Fujikura Model CT-03, CT -04, CT -04B, or CT -07, is required for the cleaving process. Note: Sumitomo Model FC-4 Cleaver may also be used, along with the 2651-A Fiber Viewer . 5.03 Lay the stripped ribbon between the guide forks.
10 6.04 Lock the spacer in place by tightening the locking screw using the supplied allen wrench. 6.05 Place the ribbon holder into the cleaver . Push the ribbon holder against the cleaver spacer gauge . 6.06 Align the end of the ribbon coating to be within the slot in the cleaver gauge.
11 6.09 Depress the cleaving lever 3 firmly . 6.10 While holding the cleaving lever down, remove the cleaved fiber stubs, and dispose of per company practice. 7.0 Visual Inspection of the Cleave 7.01 Install the fiber viewer on the cleaver and rotate the viewer barrel to focus.
12 7.03 Defect in cleaved fibers. 7.04 If fibers are properly cleaved: - Remove the fiber viewer from the cleaver , and - Remove the ribbon holder from the cleaver . defective Actuation Lever Preload Lever Preload Lever 8.0 Fiber Insertion 8.01 Move the actuation lever on the actuator tool all the way to the right.
13 8.05 Lower the front end of the ribbon holder to lay the cleaved fibers in the V grooves of the splice. If the fibers are not positioned properly in the V grooves, raise and lower the front end of the ribbon holder until the fibers are positioned properly .
14 10.0 Splice Actuation 10.01 Actuate the splice by squeezing the actuation lever slowly until it stops. 10.02 Close both splice covers. Note: Some protective gel may be visible after closing covers. 9.02 Look at the amount of bare glass where each ribbon enters the splice.
15 10.05 Turn the splice over and verify that the wedge has been fully pushed against the splice body . 10.06 If the wedge is not against the splice body , move the actuation lever to the right, place the splice back into the actuator tool and squeeze the actuation lever again.
16 c. Insert the tube guide into the pivot housing. Secure the tube guide with the tube guide lock. 1 1.02 Stripper Blades - Cleaning a. If the stripper performance is unsatisfactory after the normal cleaning procedure (section 4.10), the stripper blades may need to be removed from the handle assembly for a more thorough cleaning.
17 1 1.03 Stripper Blades - Replacement a. If the stripper performance is unsatisfactory after a thorough cleaning, the blades need to be replaced. Remove the blades per 1 1.02 b. b. Place the new blades into the pivot housing per 1 1.02 d and e. Hint 2: Stripping in Hot T emperatures: At high temperatures, the heating time will be less.
18 P/N Description Packaging Splices 2604 Fibrlok TM Multi-Fiber Optical Splice (4 Fiber) 3/Pkg; 4 Pkg/ Case 2606 Fibrlok TM Multi-Fiber Optical Splice (6 Fiber) 3/Pkg; 4 Pkg/ Case 2608 Fibrlok TM Mul.
19.
Litho in U.S.A. 3M Telecom Systems Group Important Notice All statements, technical information and recommendations related to the Seller's products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il 3M 2600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del 3M 2600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso 3M 2600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul 3M 2600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il 3M 2600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del 3M 2600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il 3M 2600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo 3M 2600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
