Manuale d’uso / di manutenzione del prodotto F107411-01 del fabbricante Aga Ranges
Vai alla pagina of 32
Elec tric R ange Ser vice Instruc tions F107411-01 ww w .aga-ranges .com This book contains man y impor tant safety messages. Always r ead and obey all safety messages.
W ARNING If the information in this manual is not follo wed exactly , a fi re ma y result causing propert y damage, personal injury or death. W ARNING The anti-tip device supplied with this range must be corr ectly fi tted when the range is installed .
3 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Sec tions Diagnostics 5 Ser vicing P roc edures 11 T echnical Data 27 Schematic.
4 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished..
5 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Diagnostics Check ing the Multifunc tion O ven 6 Check ing the Con vection O ve.
6 Check 1 Result P ossible Cause Open the oven door and turn on the o ven light Light does not work 1 No power to range 2 Light bulb failed (most likely cause) 3 F ault in power supply t o switch 4 F .
7 Check ing the Multifunc tion O ven.
8 Check 1 Result P ossible Cause Open the oven door and turn on the o ven light Light does not work 1 No power to range 2 Light bulb failed (most likely cause) 3 F ault in power supply t o switch 4 F .
9 Check ing the Con vection O ven.
10.
11 Contents 1. T o change oven light bulb . 12 2 How to Mov e the R ange for Servicing 12 3. T o Remove a Side P anel 13 4. T o Lift up the Ceramic Hob 14 5. T o replace a hob element. 15 6. T o replace a C ooktop W armer element. 15 7. T o replace the cooktop neon indicat or lights pack 16 8.
12 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Ser vicing Notes Disconnect from electricity supply before commencing servicin.
13 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. Replaceing the Range Reverse proc edure to reinstall the range and low er the front roller . Make sure the an ti-tip device is re- engaged properly when the range is r eplaced.
14 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 4. T o Lift up the Ceramic Hob Pull the range f or ward. Pull off the push fi t control panel end caps at each end and remov e the end fi xing screws under the end cap .
15 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 5. T o replace a hob element. Lift up the ceramic hob see 4. The elements are now accessible . Remove the scr ew in the center of the element and slide it out to the side.
16 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 7. T o replace the c ooktop neon indicator lights pack Lift up the ceramic hob see section 4. The neon indicator light pack is held to the support bracket by two clips.
17 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 9. T o Remove Oven Light S witch Remove c ontrol panel (see 8).
18 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 12. T o Remove a Thermostat Lift up the cooktop - see 4. Remove the c ontrol panel - see 8 Remove the ov en shelves. Undo the range rear cov er screws and lift covers clear .
19 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 13. T o Change Cooktop or Broiler C ontroller Lift up the ceramic hob top (see 4). Remove c ontrol panel (see 8). Disconnect wiring from controller – make a note of the wire colors and t erminal connections.
20 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 15. T o Remove an Oven Door Door is heavy - take care. Open oven door and r emove Handyrack (where fi tted) by springing one side out of the bracket on the door and sliding the other side free.
21 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 16 T o Adjust the Oven Door Angle The ov en doors are heavy . T ransit of the range can cause the oven doors t o move so that they are not correctly aligned.
22 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 17. T o Change O ven Door Outer P anel Remove the two plastic blanking plugs from the door handles. Remov e the 4mm Hex headed screws holding the handle to the door with the hexagon key tool.
23 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 19. T o Remove the Oven Door Seal Open oven door . The seal is held in place by small hooks on the rear face . At the corner pull seal diagonally away fr om the door centre until that hook is released.
24 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 22. T o Remove an Oven Inner Back Open the oven door .
25 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. 25. T o Remove the L eft Hand Multifunc tion Oven Bottom and T op Elements Bottom Element Pull the range f or ward to access the r ear of the range, see the section ‘How T o Move the Range for Servicing’ .
26 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished..
27 SERVICING W ARNING Disconnect from electricity before servicing. Check appliance is saf e when you hav e finished. T echnical Data DA T A BADGE L OCA TION: Inside base of drawer ca vit y - remov e drawer . For r emoval of drawer see installation instructions.
28 Schematic diagram of the R ange Caution: Label all wires prior to disconnection when servicing controls . Wiring err ors can cause improper and dangerous operation.
29 Code Description BRE Broiler elements BSB Br oiler switch block BT C Broiler contr oller CFM Cooling fan motor IGS Ignition swit ches ISG Ignition spark generat or LBE Left hand bottom element LFE .
30.
31.
Aga Ranges 110 W oodcrest Road Cherr y Hill, NJ 08003 USA 1.866.4AGA.4USA ww w .aga-ranges.c om Email suppor t@aga-ranges.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Aga Ranges F107411-01 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Aga Ranges F107411-01 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Aga Ranges F107411-01 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Aga Ranges F107411-01 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Aga Ranges F107411-01, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Aga Ranges F107411-01.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Aga Ranges F107411-01. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Aga Ranges F107411-01 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
