Manuale d’uso / di manutenzione del prodotto MS2000 del fabbricante Clarion
Vai alla pagina of 16
.
C ongratulations on your purchase of this Ungo System. Please read this manual thoroughly to familiarize yourself with your system’s components and operation. Discuss any questions you might have with your installing dealer. Record the serial number of your Ungo system and keep all dealer records and receipts.
Table of Contents 1. About Your Ungo Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 2. Remote Transmitters Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features designed to: p Deter potential intrusions to the vehicle by continually flashing the system LED status indicator while the system is Armed, giving a visual indication to any passer-by that the vehicle is equipped with a security system.
Page 2 - MS2000 Owner’s Manual Remote Transmitter Layout The Ungo MS2000 comes with 2 multi-function Remote Transmitters used to control nearly all of the system’s features. Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is taking place.
MS2000 Owner’s Manual - Page 3 Battery Replacement Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced from time to time. Under normal conditions, the battery may last for up to a year before it needs replacement.
Page 4 - MS2000 Owner’s Manual Remote Arming When Armed, the system monitors and protects 3 independent areas, or zones , including the doors, hood/trunk, and shock sensor. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. • The siren/horn will chirp once.
MS2000 Owner’s Manual - Page 5 To Bypass the sensors: 1. After arming the system, press Button 1 again on the Remote Transmitter within 5 seconds. • The siren will chirp 5 times, indicating the sensors have been bypassed. 2. The sensors will remain bypassed until the next time the system is armed.
Page 6 - MS2000 Owner’s Manual To set the Arming Mode: 1. Turn the ignition on. 2. Within 4 seconds, press Button 3 to change the setting. one chirp = Passive Arming with chirp two chirps = Active Arming three chirps = Passive without chirp 3. Turn the ignition off to save your selection.
MS2000 Owner’s Manual - Page 7 Emergency Override In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter and drive your car by using the following procedure. Be sure that you have your ignition keys ready and that you know the location of the Override switch before you perform this procedure.
Page 8 - MS2000 Owner’s Manual Valet Mode Allows you to temporarily disable the security system when the car is being service or turned over to a parking attendant. To turn Valet Mode on or off: 1. Turn on the ignition. 2. Press and hold the override switch.
MS2000 Owner’s Manual - Page 9 To operate the Auxiliary Function with the system Disarmed , press Button 3 for three seconds. • This function will stay active for as long as Button 3 is held.
Page 10 - MS2000 Owner’s Manual Technical Data Specifications Main Unit Voltage: 12v, negative ground Current Consumption: <15mA Temperature Range: -40 o F to +257 o F Auxiliary Output Capability: 500mA Internal Relays: (1) 30A, (1) 15A Transmitter Current Consumption: <.
MS2000 Owner’s Manual - Page 11 1. Ungo Security Corporation of Gardena, California ("Ungo Security") warrants this Ungo system to be free from defects in materials and workmanship and to comply with Ungo Security’s applicable printed specifications.
Ungo Security Corporation A Clarion Company 661 West Redondo Beach Blvd. Gardena, CA 90247 800-Go-Clarion www.clarion-usa.com © Ungo Security Corporation, Gardena, CA 97-MS2000-10 Rev.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Clarion MS2000 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Clarion MS2000 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Clarion MS2000 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Clarion MS2000 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Clarion MS2000, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Clarion MS2000.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Clarion MS2000. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Clarion MS2000 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
