Manuale d’uso / di manutenzione del prodotto 7920 IP del fabbricante Cisco Systems
Vai alla pagina of 24
Table of Contents Wireless IPT Design Guide for the Cisco 7920 IP Phone ................................................................................1 Introduction ....................................................................................
Wireless IPT Design Guide for the Cisco 7920 IP Phone Introduction Prerequisites Requirements Components Used Conventions Cisco 7920 IP Phone Overview WLAN Overview RF Overview Site Surveys and Design Recommendations VoIP QoS Security for the Cisco 7920 and WLAN Networks Network Sizing Number of 802.
AVVID design guides and administration. • Components Used The information in this document is based on the software and hardware versions below: The Cisco 7920 IP Phone. • The information in this document was created from the devices in a specific lab environment.
remember that the Cisco 7920 has somewhat different roaming characteristics than Cisco Aironet Network Interface Cards (NICs). This includes thresholds on the Cisco 7920 that determine when the phone roams or how much the RF environment needs to change in order to determine when a roaming event should occur.
Voice traffic can be classified with the following characteristics: Smooth VoIP packets are sent at consistent intervals with uniform packet sizes. • Benign VoIP packets only attempt to use the bandwidth necessary to send from end to end. VoIP does not use any windowing to determine data rates.
Technical Assistance Center (TAC) (if problems arise) is limited for this situation. Security for the Cisco 7920 and WLAN Networks The Cisco 7920 is supported in the architecture of the Cisco Wireless Security Suite. The architecture is discussed in detail in documents for Wireless LAN Security Solution.
RADIUS functionality in a small office, but could also be used as a ACS server in case of WAN failure. The following is a step−by−step example of configuring the fallback RADIUS server for LEAP authentication: Configure the Network Access Server (NAS), by issuing the following commands: radius−server local nas 192.
One of the key aspects when calculating network capacity for 802.11b networks is that it is a shared medium. Because of this, consideration must be given for radio contention among the various devices. This means that the back−off algorithms in 802.
All of the above calculations and design recommendations are based on VAD being disabled on the Cisco 7920 IP Phones. VAD is a mechanism in VoIP where no RTP packets are sent if no speech is occurring during the conversation. VAD can be enabled on the Cisco 7920 phones and provides some bandwidth conservation, typically around 30 percent.
30 AP limit is due to memory and processor constraints on the Wireless Domain Server (WDS), which is AP functionality to provide this enhanced roaming and security. This functionality is introduced into Cisco IOS Software Release 11.2(11)JA on the Cisco APs.
Note: Any references to roam or roaming throughout the remainder of this document is in the context of mid−call roaming. As it relates to roaming, the Cisco 7920 IP Phone currently only supports Layer 2 roaming.
this AP. If either the association or authentication fails, it continues to try the next best AP. Note: As a Cisco 7920 roams between APs, it re−authenticates with each new AP. AP B sends a null MAC multicast using the source address of the Cisco 7920.
Layer 2 roaming with both static WEP and LEAP has been shown to provide acceptable QoS using either G.711 or G.729. If LEAP is being used, it is recommended that users are defined locally on the ACS server.
VLANs VLANs are used by WLAN networks to provide two distinct functions: Segment traffic into distinct broadcast domains (IP subnets). • Create separate security domains for different security model.
For more details on deploying VLANs in WLAN networks, refer to the Wireless Virtual LAN Deployment Guide. WLAN QoS for VoIP As mentioned earlier, WLANs operate as a shared medium. This means that QoS on WLAN networks are more difficult than wired networks because end points do not have dedicated bandwidth for sending and receiving traffic.
Before discussing how WLAN QoS works, you must first understand how end points transmit data on WLAN networks. Similar to wired Ethernet networks, 802.11b WLANs employ Carrier Sense Multiple Access (CSMA). However, instead of using Collision Detection (CD), WLANs use Collision Avoidance (CA).
After the IFS expires, the end point selects a value between 0 and aCWmin. The end point waits the length of this value and determines if the medium is available to transmit.
Cisco Aironet APs support a QoS similar to EDCF as of Cisco IOS Software Release 12.0T SW. This provides up to eight queues for downstream (toward the 802.11b clients) QoS. These queues can be allocated in the following ways: Based on ToS or DiffServ settings of packets.
The following is an example of configuring the QBBS element in beacons on Cisco IOS Software−based APs: Beyond just having queuing and setting packets with the correct DiffServ markings, delay and jitter need to be taken into consideration. This is especially true for upstream traffic since there is no queuing among clients on the 802.
Disable Port Aggregation Protocol (PagP) − PagP is enabled by default, but it is not needed for user−facing ports. • Enable Port Fast Allows a switch to quickly resume forwarding traffic if a Spanning Tree Protocol (STP) link goes down.
wrr−queue cos−map 4 5 priority−queue out Connecting APs to the Catalyst 2950 EI The following configuration is a reference template for use on Catalyst switch ports that are connected to Cisco APs.
Cisco Emergency Responder can query for IP Phones through either CDP (on the Catalyst switches) or the MAC address. Since CDP is sent as a link−layer multicast and is used by the Cisco AP to determine the QoS settings for the Cisco 7920, it is not propagated up to the Catalyst switch.
Call Admission Control Call Admission Control (CAC) provides the mechanism that prevents the presence of the next voice call to interrupt or provide poor QoS for all existing voice calls. Regarding Time−Division Multiplex (TDM), this is accomplished by a finite number of DS0 channels.
Cisco 7920 does not support network−based directories. This will be supported in future software releases. • Cisco 7920 does not support XML−based applications.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cisco Systems 7920 IP è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cisco Systems 7920 IP - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cisco Systems 7920 IP imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cisco Systems 7920 IP ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cisco Systems 7920 IP, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cisco Systems 7920 IP.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cisco Systems 7920 IP. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cisco Systems 7920 IP insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
