Manuale d’uso / di manutenzione del prodotto OSR-7609 del fabbricante Cisco
Vai alla pagina of 24
Corporate Headquarters: Copyright © 20 04–20 06 Cisco Systems, Inc. All rights reserved. Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Catalyst 6509-NEB Switch and Cisco O.
2 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Contents Contents This publication co nsists of the following sections: • Safety Overvie w , page 2 • Parts List, pa.
3 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Parts List War ni ng Only trained and qualified personn el should be allowed to install, replace, or service this equipment. Statement 1030 War ni ng Hazardous voltage or energy is present on the backplane when the sy stem is operating.
4 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Installation Guidelines Installation Guidelines Follo w these guidelines wh en upgrading the ch assis: • If your switch or rou ter is using an A C-input po wer supply , you are required to install t h e WS-CA C-3000W po wer supply .
5 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Panel Safety Cover War ni ng This unit might have more than one power supply connection.
6 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Pa ne l Safety Cover Figur e 1 Removin g the P anel Safety Co ver Step 3 On the ne w panel safety cov er , grasp the panel handl e and press th e panel into place, startin g at the bottom of the chassis and wo rking up.
7 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Fan Tra y Figure 2 Installing the P anel Saf ety Cover Replacing the Fan Tray This section descri bes ho w to remove and instal l the fan tray for the Catalyst 6509-NEB switch and Cisco OSR-7609 Router .
8 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Fa n Tray Removing the Fan Tray War ni ng When removing the fan tray , keep your hands and fingers away from the spinning fan blades. Let the fan blades completely stop before you remove the fan tray .
9 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Fan Tra y Installing the High Speed Fan Tray T o install the high speed fan tray (W S-C6509-NEB-F AN2), follo w these steps: Step 1 Hold the fan tr ay with the f ans facing do wn and the F AN F AIL LED on the right .
10 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Po wer Supply Replacing the Power Supply Note DC-input systems —See the “Connecting Site Power to the Fan T r ay for DC-Input Systems” section on page 15 to connect site po wer to the high speed fan tray .
11 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Power Sup ply Figur e 6 Remov ing an AC-Input P ow er Supply FAN STA TUS 105074 SUPERVISOR2 WS-X6K-SUP2-2GE.
12 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Po wer Supply Installing the 3000 W AC-Input Power Supply Caution Use both hands to install and remove po wer supplies . Each Catalyst 6500 series A C-input po wer supply weighs between 22 pou nds (9.
13 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Connecting Power to the Fan Tray Figure 8 Installing the 30 00 W Po wer Suppl y Step 4 T igh ten the power supply captive installation sc re w . (See Figure 7 .) Step 5 If you ha ve a redundant po wer supply , install it now fol lowing the st eps in this section.
14 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Connecting Pow er to the Fan Tray Installing the Fan Tray Power Cable for AC-Input Systems Note The fan tray ships with power wires secured at each terminal block. Use these wires to co nnect the fan tray to the 3000 W A C-input po wer supply using the supplied cables.
15 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Connecting Power to the Fan Tray Connecting Site Power to the Fan Tray for DC-Input Systems Note T o provide redun dancy , you may choose to connect eac h f an terminal block to a separate po wer source.
16 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Connecting Pow er to the Fan Tray Figure 12 Removing the T er minal Block Cov er Step 3 W ith a flat blade scre wdriv er , disconnect the input wires from the t erminal block.
17 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Supervisor Engine Figur e 14 DC-Input Wire Connecti ons on the T erminal Block War ni ng When installing or replacing th e unit, the ground conn ection must alway s be made first and disconnected last.
18 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Su pervisor Engine Step 3 Loosen the two capt i ve installa tion scre w s on the supervisor en gine.
19 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Replacing the Supervisor Engine Step 8 Using the t humb and forefinger of ea ch hand, grasp th e two ejector le vers and ex ert a sl ight pressure to the left, deflecting the mo dule approximately 0.
20 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Replacing the Su pervisor Engine Figur e 16 Clear ing the EMI Gask et in the Chassis INPUT OK FAN OK OUTPUT FAIL OUTPUT.
21 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Powering Up the Syste m Figur e 1 7 Eject or Lever Closur e in the Chassis Powering Up the System This section descri bes ho w to power up the system.
22 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Verifying Installation DC-Input Systems T o po wer up your DC-input system, f ollow these steps: Step 1 Remov e the tape from the circuit break er switch handle, and restore power by moving the circuit b reaker switch handle to the On (|) po sition.
23 Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note 78-16162-02 Related Documentation Related Documentation For additi onal information on Catalyst 6500 se ries switches and command-lin.
24 Catalyst 6509-NEB Switch and Cisc o OSR-7609 Ro uter Upgrade Note 78-16162-02 Obtaining Documentation an d Submitting a Se rvice Request.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cisco OSR-7609 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cisco OSR-7609 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cisco OSR-7609 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cisco OSR-7609 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cisco OSR-7609, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cisco OSR-7609.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cisco OSR-7609. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cisco OSR-7609 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
