Manuale d’uso / di manutenzione del prodotto ASR1002 del fabbricante Cisco
Vai alla pagina of 46
Q UICK S TART G UIDE Cisco ASR 1002 Router 1 Documentation and R esources 2 Prepare for Installation 3 Rac k-Mount the Router 4 Connect the Rou ter to the Network 5 Star t the System 6 Configuring the.
2 1 Documentation and Resources Documentation for the Cisco 1000 Series Ag gregation Services Routers documen tation is available online, w ith the exception of the regulatory compliance and safety documentation a nd the Cisco 1000 Series Aggre gation Services Routers documentation.
3 2 Prepare for Installation This section contains information about the tools and parts, wa rnings, site preparation information, and other information for the rack-mount installation and equipment shelf or tableto p installation. War n in g Only trained and qualified p ersonnel should instal l, replace, or service this equipment.
4 Prepare for Rack-Mount Installation Before you begin the rack-mounting tasks: • Decide whether or not you want to rear -mount the chassis from the front or the rear . • Decide whether or not you want to attach ca ble-management brackets to your chassis.
5 Attach the Rack-Mount Bracke ts—Chassis Rear-Mounted T o install the rack-mount brackets on a Cisco ASR 1002 Rout er in a rear rack-mount configu ration, follow these steps: Step 1 Locate the threaded ear holes in the rear sides of the chassis.
6 Figure 3 shows the Cisco ASR 1 002 Router in a four -post rack. Figur e 3 Installing the Cisco ASR 1 0 02 Router in a Four -P ost Rack - F ront and Rear Rac k-Mounting Note Because the rack-mount brack ets suppor t the weight of the entire chassis, use al l the screws to fasten the two rack-mount brackets on the chassis to the rack posts.
7 Step 8 Insert the bottom screw fir st and then the second screw at the top of the chassis, diagon ally from the bottom screw . This helps secure the chassis in place while you in sert the other screws.
8 Figure 4 shows the Cisco ASR 1002 Router in a two-post rack . Figur e 4 Installing a Cisco ASR 1 0 02 Router in a T wo- P ost Rack T o install the Cisco ASR 1002 Router in a two- post equipment rack, perform the following steps: Step 1 Pos ition the chassis such that the front is closest to you an d lift it carefully into the rack.
9 Attach a Cable-Management Bracket The cable-management bracket should be m ounted to each rack-moun t bracket on the chassis to provide cable-management to both sides of the chassis. These brackets are mounted to the rack-mount brackets usin g screws to allow ea sy installation and removal of cables.
10 This completes the procedure for inst alling the cable-management bracket s on a Cisco ASR 1002 Router for a chassis rack-mount configuration . Chassis Ground Con nection Installation Connecting th.
11 Step 2 Insert the A WG #6 wire into the wire receptacle in the groundin g lug. Step 3 Use the manufacturer’ s recommended crimping tool to carefully crimp the wire recept acle around the wire. This step is required to ensure a proper mechanical connection.
12 Step 6 Insert the two screws through the holes in the groundi ng lug. Step 7 Use the Number 2 Phillips screwdriver to carefully ti ghten th e screws until the grounding lug is held firmly to the chassis.
13 Step 2 Connect to the port using the RJ-45-to-DB-9 cable. Step 3 After you establish normal router operat ion, you can disconnect th e terminal. Note For information about console port and auxiliar.
14 Figur e 1 1 Cisco ASR 1 0 02 Integrat ed Route Pr ocessor Cable-Managements T o secure shared port adapte r interface cabl es and inp ut or output cables connected to the Cisco ASR 1002 Router , follow these steps: Step 1 When installing the network interface cables, route the ca bles up to and through the cabl e-management bracket U device.
15 Read the safety warnings before y ou begin. War n in g Never install an AC power modul e and a DC power module in the same chassis. Statement 1050 War n in g Installation of the equipme nt must comply with local and national electrical c odes.
16 LED Label LED Color Description INPUT OK Power supply activity Green The AC powe r supply input voltage is greater than 85V . None The AC input voltage is less than 70V or the power supply is turned off.
17 Connecting AC Power to t he Cisco ASR 1002 Router Step 1 Insert an AC power supply in po wer supply Slot 0 or power supply Slot 1 until it is full seated. Step 2 T ighten the captive installation screws. Step 3 At the rear of the router , check that the power switch is in the Off (O) position.
18 Figur e 15 AC P ower Supply Cor d Cabl ing for the Cisco A SR 1 002 Router Note Using a tie wrap for the AC pow er cable is optional and n o t necessary . However , if you do attach the AC power cable to a power supply tab and th en you remo ve the AC power cable for some reason, check for any damage to the cable after you cut the tie wrap off.
19 Figur e 16 –48V DC P ow er Supply for the Cisco ASR 1 002 Router Table 2 describes the –48V DC power supply LEDs on the Cisco ASR 1002 Router . T able 2 Cisco A SR 1 0 02 Router –4 8V DC P ow er Supply LEDs Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site.
20 Figur e 17 Cisco ASR 1 0 02 Router –48V DC T erminal Bloc k War n in g Never install an AC power modul e and a DC power module in the same chassis. Statement 1050 War n in g Installation of the equipme nt must comply with local and national electrical c odes.
21 Figur e 18 Cisco ASR 1 0 02 Router –48V DC P o wer Supply Step 5 Insert the stripped end of the ground lead all the w ay in to th e ground lead re ceptacle on the –48V DC-input power supply , and tighten the receptacle screw using a 3.5 mm flat-blade screwdriver to a torque of 0.
22 Connecting +24V DC Power to the Cisco ASR 1002 Router The +24V DC power supply uses a spring-l oaded terminal block. The input terminal block requires 8 A WG multi-strand wiring to support input current. Features are provide for strai n relieving the input wires from the terminal block on the front panel.
23 T o connect +24V DC power supply in the Cisco ASR 1 002 Router , follow these steps: Step 1 At the rear of the router , check tha t the po wer Standby switch is in the Standby position. Step 2 Ensure that the positive and negative leads are discon nected from the site power source an d the source circuit breaker is turned off.
24 Step 6 With the screwdriver still inserted , gently push the lead wire (ground lead first) in until it is fully inserted as shown in Figure 22 . Caution Check that there is no copper portion of the lead wire exposed. Y ou only want the wire insulation visible.
25 Step 7 After the lead wire is fully inserted, hold the lead wire in pl ace by pressing inward while you remove the screwdriver to release the spring to tension down on the installed lead wire. Step 8 Once the screwdriver is complete ly removed, gently pull on the lead wire to make certain that the lead wire is securely installed.
26 Figure 25 Cisco ASR 1 002 Router +24V DC Po wer Supply Lead Wires Installed Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site.
27 Figure 26 Cisco +24V DC P o w er Supply T e r minal Bloc k Ground Lead Service Loop Caution When securing the ground, positive, and negative +24V DC-i nput leads to the power supply faceplate, leav.
28 MCP_SCAL_R1#sho plat Chassis type: ASR1002 The following output displays: MCP_SCAL_R1# If the LEDs indicate a power problem or the power supply state is ps,fail, then contact a customer service representatives for assistance or additional instructions.
29 Table 4 pro vides information about the Cisco ASR1 000-ESP5 LED s in the Cisco ASR 1002 Router as the system starts. T able 4 Cisco ASR1 00 0-ESP5 and ASR1 00 0-ESP1 0 LED Activity During the boot process, observe the syst em LEDs. The ST A TUS LED comes on immediatel y as amber , then turns to green when the Cisco IOS is booted.
30 Note The system boots differently depending on the configuration that ships with your system. The display below is a snapshot of messages that are output on the console of the Cisco ASR 1002 Router system after power -up and during IOS booting. This is only an example of what yo u might see from any Cisco ASR 1000 Series Router .
31 All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY.
32 Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre*Feb 13 13:01:36.253: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded from the Shell Manager *Feb 13 13:01:36.
33 Configure Global Parameters Using the Set-up Facility When you first start the setup program, you must configure th e global parameters. These parameters are used fo r controlling system-wide settings. Complete the foll owing steps to enter global parameters: Step 1 Connect a console terminal to the console port.
34 Enter host name [Router]: The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.
35 ! interface GigabitEthernet0/1/1 shutdown no ip address ! interface FastEthernet0/3/0 shutdown no ip address ! interface FastEthernet0/3/1 shutdown no ip address ! interface FastEthernet0/3/2 shutd.
36 ASR1000-RP1 platform with 2097152 Kbytes of main memory rommon 1 > b tftp:images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin IP_ADDRESS: 2.1.6.5 IP_SUBNET_MASK: 255.255.0.0 DEFAULT_GATEWAY: 2.1.0.1 TFTP_SERVER: 2.0.0.2 TFTP_FILE: images/packages_crypto/asr1000rp1-advipservicesk9.
37 A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1000 (RP1) processor with 548011K/6147K bytes of memory.
38 Perform Other Configuration Tasks T o make advanced configuration changes after yo u establish the basic startup configuration for your router , refer to the Cisco ASR 1000 Series Aggregation Servi.
39 Current image running: Boot ROM0 Last reset cause: LocalSoft ASR1000-RP1 platform with 4194303 Kbytes of main memory mcp-2ru-1-rp0-rommon 1> Step 5 Remove any power cables fro m the Cisco ASR 1002 Router . a. For power supplies with a circuit breaker switch, position the switch to the Off (O) position.
40 Y ou hav e completed the procedure for replacing the Cisco ESP5 or ESP10. Replace the Shared Port Adapters The shared port adapters (SP As) on the embedded Cisco ASR10 00-SIP10 in the Cisco ASR 1002 Router support online insertion and removal (OIR); but the embedded Cisco ASR1000-SIP10 does not su pport OIR and is not field-upg radeable.
41 Removing an AC Power Supply T o remove a Cisco ASR 1002 Router AC power supply that is not o perating normally (and th en replace the AC power supply within five minutes), follow this procedure: Step 1 Slip on the ESD-preventive wri st strap th at was includ ed in the accessory kit.
42 Removing the –48V DC Power Supply Before you can remove a –48V DC power supply from the Cisco AS R 1002 Router , you must remove power from the power supply . Caution Make certain that the chassis ground is connected before you begin removing and installing the power supply .
43 Figur e 27 Cisco ASR 1 002 Router +24V DC P ow er Supply T er minal Bl ock and Labels • The ground (GND) lead is always installed first an d removed last. • The +24V DC power supply uses a spring loaded terminal block; therefore have th e re commended scre wdriver size available.
44 Figur e 28 Removing the Cisco ASR 1 002 Ro uter +24V DC P ow er Supply Lead Wir es Step 4 Remove the s crewdriver a nd continue rem oving the rema ining lead wires from the terminal block, repeating Step 3 and Step 4 for each lead wire. Ti p If the 8-gauge input wiring is very rigid or a solid wire, then a screwdriver might not be nece ssary .
Americas Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .
46.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Cisco ASR1002 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Cisco ASR1002 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Cisco ASR1002 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Cisco ASR1002 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Cisco ASR1002, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Cisco ASR1002.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Cisco ASR1002. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Cisco ASR1002 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
