Manuale d’uso / di manutenzione del prodotto WEATHERMAKERTM TWO-SPEED 38TDB del fabbricante Carrier
Vai alla pagina of 16
38TDB WeatherMaker™ Two-Speed Air Conditioning Unit with Puron® Installation and Start-Up Instructions NOTE: Read the entire instruction manual before starting the installation.
INSPECT EQUIPMENT File claim with shipping company prior to installation if shipment is damaged or incomplete. Step 2—Install on a Solid, Level Mounting Pad If conditions or local codes require the unit be attached to pad, tie down bolts should be used and fastened through knockouts provided in unit base pan.
8. Install vapor elbow (see Fig. 5B) with equalizer adapter to suction tube of line set and suction connection to indoor coil. Adapter has a 1/4-in. male connector or attaching equalizer tube. 9. Connect equalizer tube of TXV to 1/4-in. equalizer fitting on vapor line adapter.
Do not leave system open to atmosphere any longer than minimum required for installation. POE oil in compressor is extremely susceptible to moisture absorption. Always keep ends of tubing sealed during installation. If ANY refrigerant tubing is buried, provide 6–in.
5. Repeat this procedure as indicated in Fig. 9. System will then contain minimal amounts of contaminants and water vapor. FINAL TUBING CHECK IMPORTANT: Check to be certain factory tubing on both indoor and outdoor unit has not shifted during shipment.
O/ W2 W/W1 Y1 / W 2 G R THERMIDIST A T CONTROL MODEL RH V ARIABLE-SPEED CONDENSING FURNACE TW O-SPEED AIR CONDITIONER W/W1 G Y/ Y2 C Y2 R Y1 C DHUM HUM B S1 S2 W2 R C HEA T ST AGE 1 COOL ST A GE 1 COO.
COOL ST AGE 1 FA N HEA T ST AGE 1 COOL ST AGE 2 N/A 24 V A C HOT R W/W1 Y/Y2 O/W2 Y1/W2 G 24 V A C COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y2 C PROGRAMMABLE THERMOST A T MODEL 2S SINGLE-ST AGE .
required. The LCC for standard PSC blower products consists of a standard humidistat which opens contacts on humidity rise and a pilot duty relay with 24v coil. NOTE: If an LCC is desired, low-speed airflow must be main- tained so that a minimum of 300 CFM/ton can be supplied during high speed LCC operation.
A01222 LEGEND 24 VOL T F ACTORY WIRING 24 VOL T FIELD WIRING FIELD SPLICE CONNECTION RELA Y SPDT , PILOT DUTY 24-V COIL (HN61KK324) OR EQUIV ALENT HUMIDIST A T , OPENS ON HUMIDITY RISE (HL38MG026) AIRFLOW SELECTOR R1 H AFS WIRING DIAGRAM NOTES: 1. WIRING MUST CONFORM TO NEC OR LOCAL CODES.
Step 10—Start-Up To prevent compressor damage or personal injury, observe the following: • Do not overcharge system with refrigerant. • Do not operate unit in a vacuum or at negative pressure.
Step 11—Check Charge Service valve gage ports are not equipped with Schrader valves. To prevent personal injury, make sure gage manifold is connected to the valve gage ports before moving valves off fully back seated position. Wear safety glasses and gloves when handling refrigerant.
FACTORY DEFAULTS Factory defaults have been provided in the event of failure of outdoor air thermistor, coil thermistor, and/or furnace interface jumper. ONE MINUTE SPEED CHANGE TIME DELAY When compressor changes speeds from high to low or low to high, there is a 1-minute time delay before compressor restarts.
Compressor Control Contactors Low and high capacity contactor coils are 24 volts. The electronic control board controls the operation of the low speed (C-L) and the high speed (C-H) contactors. TEMPERATURE THERMISTORS Thermistors are electronic devices which sense temperature.
Fig. 15—Wiring Diagram—024, 036, 048 A01513 CONNECTION DIAGRAM OCT -t ° LPS HPS OAT -t ° LO HI TO INDOO R UN IT RED CCH FA N C A P YEL RED BRN OFM BL K BL U/ PNK BLU/ PNK YEL / PNK YEL / PNK BRN.
Fig. 16—Wiring Diagram—037 A01439 CONNECTION DIAGRAM OCT -t ° LPS HPS OAT -t ° LO HI TO INDOOR UNIT CCH RED BRN BLU/ PN K BLU/ PN K YEL/ P NK YEL/PNK BRN BRN BLK BLK RED BLU CH 11 21 23 23 YEL B.
→ Fig. 17—Wiring Diagram—060 A02212 CONNECTION DIAGRA M OCT -t ∞ LPS HPS OAT -t ∞ LO HI T O IN DO O R U NIT RED CCH FA N C A P RED BRN OFM BL K BL U/ PNK BLU / PN K YEL / P NK YEL / PN K BRN.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Carrier WEATHERMAKERTM TWO-SPEED 38TDB è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Carrier WEATHERMAKERTM TWO-SPEED 38TDB - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Carrier WEATHERMAKERTM TWO-SPEED 38TDB imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Carrier WEATHERMAKERTM TWO-SPEED 38TDB ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Carrier WEATHERMAKERTM TWO-SPEED 38TDB, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Carrier WEATHERMAKERTM TWO-SPEED 38TDB.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Carrier WEATHERMAKERTM TWO-SPEED 38TDB. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Carrier WEATHERMAKERTM TWO-SPEED 38TDB insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
