Manuale d’uso / di manutenzione del prodotto TLM TLM-1705 del fabbricante Tatung
Vai alla pagina of 28
OPERATING INSTRUCTIONS TLM-1705 / TLM1905.
.
i P REFACE FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartio n is subjected to the following two conditio ns: 1. This device m ay not cause harm ful interference, and 2. This device must accept any interfe rence received, including interference that ma y cause undesired operation.
ii The Federal Comm unicati ons Comm ission warns that changes or m odificat ions of the unit not expressl y approved by the party responsi ble for com pliance could void the user’s authority to operate the equipm ent.
iii Important Operating Instructions Please read the following i nstructions carefully. Thi s manual should be retained for future use. 1. To clean the LCD monitor screen, first, make sure the monitor is in th e power off mode. Unplug t he monit or from it s power source before cleaning it.
iv Introduction CONTENTS PREFACE ..................................................................................................................... I CHAPTER 1 ........................................................................................
1 C HAPTER 1 The LCD Multimedia Monitor Unpacking After you unpack your LCD multimedia monitor, ma ke sure the follo wing items are included in the box and in good condition: Standard Item • LCD mul.
2 Identifying Components The LCD Multimedia Monitor — Front View Figure 1-1: The LCD multimedia Monitor Front View 1. Power-On Indicator This LED indicator stays lit when the power is o n and blink s when the LCD multimedia monitor is in power saving mode .
3 1. Audio Line-in 2. AC Power Jack 3. VGA (Analog) Cable With 15-Pin D-Sub VGA Connector (Male) 4. S-Video connector 5. AV connector 6. Digital VGA (DVI) Cable Connector (Optional) Adjusting the Tilting Angle The LCD multimedia m onitor’s angle settings ran ge from -3 ° to 20 ° .
4 Raising Your Monitor to an Upright Position and Adjusting Monitor Angle.
5 Power Management System The LCD multimedia m onitor complies with the VESA DPMS pow er management proposal. When th e LCD multimedia m onitor is in pow er saving mode or detects an in correct timing, the monitor screen will be blank an d the pow er LED indicator starts blin king.
6 C HAPTER 2 The Display Controls LCD Multimedia Monitor Control Panel Figure 2-1: The LCD Monitor Panel 1. OSD Menu Button Press this button t o pop up the OSD (On-Screen Display) m enu. This button is al so a Function Select but ton . 2. Adjustment Control Buttons These two buttons all ow you to adjust the selected control functions in the OSD.
7 Adjusting the Monitor’s Display OSD Main Menu To access the OSD main m enu, press the OSD Menu button. Use the Funct ion Select buttons to scro ll between the OSD main menu options.
8 H-POSITION: To move the LC D monit or’s display le ft or right on a horizontal pl ane. V-POSITION: To move the LC D monit or’s display up or down on a vertical plane. PHASE: To adjust the focus and clarity of the disp lay. CLOCK: To adjust th e display pixel alig nment.
9 EXIT: To exit the OSD-Control subm enu. GRAPHIC-CONTROL Option The Graphic-Control opt ion lets you m ake adjustm ents that effect the contrast, brightness and color of the LCD m onitor’s di splay. Press the Adjustm ent control butt on to display the submenu.
10 Press the Adjustm ent control butt on to display t he submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Ital ian and Japanese. AUDIO VOLUME: To increase or decrease the volume of the LCD moni tor’s sound system .
11 OSD-CONTROL Option The OSD-Control m enu option l ets you adjust t he position of the OSD on the screen. Press the Adjustm ent control butt on to display t he submenu. Use the Function Select buttons to sel ect one of the following submenu opti ons: OSD-H-POSITION: To change the position of t he OSD on a horizontal pl ane.
12 MISC-CONTROL Option The Misc-Control menu opti on lets you sel ect the OSD display language, adjust the audio volum e setting and view sy stem i nformation. Press the Adjustm ent control butt on to display t he submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Ital ian and Japanese.
13 EXIT: To exits the Monitor-Control submenu. OSD-CONTROL Option The OSD-Control m enu option l ets you adjust t he position of the OSD on the screen.
14 SATURATION: To adjust the color level you prefer. SHARPNESS: Press the adjustment butto n to optimize the sharpness for your specific appli cation. RESET: To reset all of the Video-C ontrol submanu set tings to the factory default. EXIT: To exit the Video-Control subm enu.
15 Note: 1. No Video When th e monitor is ON and there is no Video signal received, the following message will be displayed . 2. Signal out of monitor’s support ed range (Please refer to Addendum) W.
16 Hot-Key Buttons for Quick Adjustment of Monitor Settings. ( 〝 AUTO-ADJUST 〞 hot-key is effective only when analog input signal is selected for application) 1. " Auto-adjust " hot-key button: Press button 2 to apply the moni tor setting automatically.
17 A PPENDIX A Troubleshooting Troubleshooting Procedures This LCD monitor com es pre-adjusted w ith standard VGA tim ing. Due to output timing differences am ong various VGA car ds, you may initially experience an unstable or unclear display when a new display m ode or new VGA card is selected.
18 2. Turn off the LCD monitor and then turn it back on again. Press the OSD Menu button (refer t o Chapter 2) once and then press either Adjustment Control bu tton several times. If there is still no display, press t he other Adjustm ent Control but ton several times.
19 A PPENDIX B Technical Information LCD Monitor Specifications LCD Panel 17-inchTFT Control Functions Power Software switch w ith LED indicator (toggle ON/OFF) Main Menu Submenu ANALOG MOD E: MONITOR.
20 Display Area 337.920 mm x 270.336 mm (17.0-inch diagonal) Display Colors 16M Video Input VGA, DVI (O ptional), S-Video, AV Scanning Frequency (Analog mode) 24-80K 56-75 Scanning Frequency H/V, Hz (Digital mode)- (Optional) 31-80K 56-75 Power Management Meets VESA DPMS Power Consumption ON : 40W max.
21 A PPENDIX C Supported Timing Ite m Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) Sy nc Polarity or composite sy nc (H/V) Operatin g Mode 1 NEC PC98 640x400 25.20 70.15 31.50 -/- A/D 2 NEC PC98 640x400 21.
6200564280 TATUNG COMPANY OF AMERICA 2850 El Pres i d i o ST. Long Beach, CA 90810 (800) 827-2850 www.tatungusa.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Tatung TLM TLM-1705 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Tatung TLM TLM-1705 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Tatung TLM TLM-1705 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Tatung TLM TLM-1705 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Tatung TLM TLM-1705, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Tatung TLM TLM-1705.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Tatung TLM TLM-1705. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Tatung TLM TLM-1705 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
