Manuale d’uso / di manutenzione del prodotto 141 del fabbricante Husqvarna
Vai alla pagina of 18
Husqvarna Operator's Manual _ 136 / 141 Instruction Manual Read and follow all Safety Rules and Operating Instructionsbefore usingthis product. Failureto do so can result in serious injury.
1 2 3 _23 24 21 9 10 1. Cylinder Cover 2. Front Handle 3. Front Hand Guard 4. Starter Cover 5. Chain Oil Tank 6. Starter Handle 7. CarburetorAdjusting Screw 8. Choke Control 9. Rear Handle 10. ON/OFF Stop Switch 11. Fuel Tank 13. Bar Tip Sprocket 14. Saw Chain 15.
_WARNING: Always disconnect spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments.
Thereshould be no smoking, openflames, or work that could cause sparks. AIIowen- gine to coolbefore refueling. • Mix and pourfuel in an outdoor areaon bare ground; store fuel in a cool,dry, well ventilated place;and use an approved, marked container for all fuel purposes.
I t Elbow locked Thumb on undersideof handlebar • Keep a good, firm grip on the saw with both hands when the engine is running and don't let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar.
• Tip contact in some cases may cause a lightning fast reverse REACTION, kicking the guide bar u p and back toward the oper- ator. • Pinching the saw chain along the top ofthe guide bar may push the guide bar rapidly back toward the operator.
Location of shipping spacer .,_tters Dep i Gauge Bar Clamp/ /_ Cha_ t0 0 Bar Clamp Nuts Drive Links Bar Tool • An adjusting pin and screw is used to ad- just the tension of the chain. It is very im- portant when assembling the bar, that the pin located on the adjusting screw aligns intoa hole in the bar.
• if chain is too loose, turn adjusting screw 1/4 turn clockwise. .,J-_,_ii_oi Adjusting / ,/ Chain Brake Nuts Guide Bar Adjusting Screw - 1/4 Turn • Lift up the tip of the bar and tighten the chain brake nuts with the bar tool. • Recheck chain tension.
For cold weather starting, start the unit at full choke; allow the engine to warm up before squeezing the throttle trigger. NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.
wrist against the hand guard without releas- ingyour griparound the front handle. The chain should stop immediately. Inertia activating function control _k, WARNING: When performing the fol- lowing procedure, the engine must be turned off. The chain brake must be checked several times daily.
Final (felling) cut here. 2" (5 cm) above center of_otch. First cut ,5 c_ _ / --, :÷1 / -- x!". /I Seco_6 cut_ __Notch : .... _ 5 cm • After removing the cutout of wood, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches higher than the center of the notch.
BUCKING WITHOUT A SUPPORT • Overcut through 1/3 of the diameter of the log. • Roll the log over and finish with a second overcut. • Watch for logs with a compression side to prevent the saw from pinching. See il- lustration for cutting logs with a compres- sion side.
_',WARNIN_: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so. d}JLWARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.
CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpeningto a professional chain sharpener. IGNITION TIMING Ignition timing is fixed and nonadjustable. SPARK PLUG The spark plug should be replaced each year to ensure the engine starts easier and runs better.
SECTION 1 : LIMITED WARRANTY Husqvama Forest & Garden Company ("Husqvarna") warrants Husqvama product to the original purchaser to be free from defects in material and workmanship from t.
DEFINED IN THE LIMITED WARRANTY STATEMENT HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITH- OUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.
purchase. WHAT IS COVERED: REPAIR OR REPLACEMENTOF PARTS. Repairor replacement of any warranted part will be performed at no charge to the owner at an approved HUSQVARNA servicing center.
Husqvama Printed in U.S.A..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna 141 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna 141 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna 141 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna 141 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna 141, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna 141.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna 141. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna 141 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
