Manuale d’uso / di manutenzione del prodotto 536.772101 del fabbricante Craftsman
Vai alla pagina of 31
3.5 Horsepower 9 Inch EDGER MODEL NO. 536.772101 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product.
TABLE OF CONTENTS WARRANTY STATEMENT SAFETY RULES INTERNATIONAL SYMBOLS ASSEMBLY OPERATION MAINTENANCE 2 SERVICE AND ADJUSTMENT 17 3 TROUBLE SHOOTING CHART 20 5 EDGER REPAIR PARTS 21 6 ENGINE REPAIR P.
SAFETY RULES Safe Operation Practices for Edger. WARNING: Look for this symbol to point out important safety precautions. It means: "Attention! Become Alertt Your Safety Is Involved.
Safe Storage • Always refer to the owner's manual instruc- tions for important details if the Edger is to be stored for an extended period. SAFETY RULES spect the Edger for any damage, and re- pair the damage before restarting and operating it.
SAFETY RULES INTERNATIONAL SYMBOLS IMPORTANT: Many of the following symbols are located on your unit or on literature sup- plied with the product. Before you operate the unit, learn and understand the purpose for each symbol. Control And Operating Symbols Slow Fast Fuel Oil Primer Button Safety Warning Symbols WARNING WARNING Thrown Objects.
ASSEMBLY ASSEMBLY Parts Packed Separately In Carton 1 - Owner's Manual (not shown) 1 - Container Of Oil 2 - Hair Pin 1 - Control Rod 1 - Control Rod 1 - Container of Oil 1 -HairPin _lb WARNING: Always wear safety glasses or eye shields while as, sembling the Edger.
ASSEMBLY HOW TO RAISE THE HANDLE 1. Loosen the knobs and raise the upper handle to the upright position. See Figure 2. 2. Tighten the knobs. Make sure the knobs are to the outside of the handles as shown in Figure 2. 3. Insert the end of the control rod, from RIGHT to LEFT, through the hole in the front wheel arm.
ASSEMBLY HOW TO PREPARE THE ENGINE Fill With Oil This Edger was shipped with a 20 ounce container of SAE30 motor oil. Add this oil to the engine before operating. To fill the crank- case, remove the oil fill cap/dipstick and add the SAE30 motor oil. DO NOT OVERFILL.
ASSEMBLY _" CHECKLIST For the best performance and satisfaction from this quality product, please review the following checklist before you operate the Edger: #-" All assembly instructions have been completed. Check carton. Make sure no loose parts remain in the carton.
OPERATION KNOW YOUR EDGER READ THE OWNER'S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERATE the Edger. To familiarize yourself with the location of the controls, compare the illustrations with your Edger.
OPERATION _IL ARNING: When the engine runs, the blade will rotate. To prevent injury, keep hands and feet away from blade. HOW TO STOP THE EDGER 1. Move the depth control lever forward to raise the blade. Then, release the engine stop lever. See Figure 8.
OPERATION HOW TO STOP THE ENGINE To stop the engine, release the engine stop ieven If the engine continues to run, move the throttle control to the STOP position. If the engine will not stop, hold a screwdriver against the spark plug and against the en- gine cooling fins.
OPERATION EDGING TIPS • Edging is best performed when conditions are dry. If the soil is to wet, dirt becomes packed around the blade causing prema- ture belt wear and decreased perfor- mance. • If dirt does become packed around the blade, stop the engine and remove the wire from the spark plug.
MAINTENANCE CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you Before Every Every Before complete regular Each 10 25 Each Before service. Use Often Hours Hours Season Storage I I Lubdcate All Pivot i = I I Points _/ ' ' ,_/ ' SERVICE DATES Lubricate Wheel Axles I Check Engine Oil .
MAINTENANCE LUBRICATION After each 25 hours, apply a small amount of engine oil to all moving parts, particularly the wheels. How To Change The Engine Oil Change the oil in the engine crankcase after each 25 hours of use. NOTE: The oil will drain more freely when the engine is warm.
MAINTENANCE SPARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted, burned, or if the porcelain is cracked. moval. Tighten the spark plug to a torque of 15 foot-pounds. 1. Make sure the spark plug is clean.
SERVICE AND ADJUSTMENT HOW TO REMOVE THE BELT The belt made of a special compound. If the belt becomes worn or breaks, replace the belt with an original equipment belt. 1. Disconnect the spark plug wire from the spark plug. 2. Drain the gasoline and oil from the en- gine.
SERVICE AND ADJUSTMENT HOW TO REPLACE THE BLADE The blade is subject to wear and damage, such as nicks and dents. This will not gener- ally affect its function. The blade is designed to not require sharp- ening. Do not attempt to sharpen the blade. The blade is also reversible.
SERVICE AND ADJUSTMENT STORAGE _1_ WARNING: Never store the Edger indoors with fuel in the fuel tank. Never store in an en- closed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, wa- ter heater or clothes dryer.
TROUBLE SHOOTING CHART TROUBLE CAUSE Engine difficult to start Stale fuel or Engine runs erratically or Engine will not run at full speed Clogged fuel filter Dirt in fuel tank or out of fuel Carburetor out of adjustment Fouled spark plug Dirty air filter Engine smokes Plugged air filter excessively Clean debris from blade.
CRAFTSMAN 536.772101 REPAIR PARTS 22 301 305 320 10 321 321 317 318 311 314 316 315 339589C KEY NO. DESCRIPTION 10 3.5HP 143.003502 (SeeEnginepages) 12 Screw 20 Pulley, V3L 22 Key, Hi Pro #505 100 Frame, Edger 300 Quill Assembly 301 Spring 302 Spring Pin 305 Belt, V4L 310 Blade Guard F=001101M KEY PARTNO.
CRAFTSMAN 536.772101 REPAIR PARTS 418 412 416 420 405 415 403 423 343712C F_OO1101M 22.
CRAFTSMAN 536.772101 REPAIR PARTS KEY NO. DESCRIPTION 401 Bolt, 5/16-18x.75 402 Nut, 5/16-18 403 Lower Handle 405 Handle, Depth 406 Screw 407 Spring, Compression 408 Nut, 5/16-18 409 Brkt, Adj.
CRAFTSMAN 536.772101 REPAIR PARTS 121 106 121 103 105 110 109 103 103 111 114 112 113 343716B KEY KEY NO. DESCRIPTION PARTNO. NO. DESCRIPTION 101 Rod, Axle Front 740091 109 Screw 103 Ring, Ret E. 20864 110 Flat washer 104 Arm, Front Wheel 740126-833 111 Nut, 5/16-18 105 Rod, Axle R.
CRAFTSMAN 143.003502 REPAIR PARTS 130 416 1; 126 119 125 -12B 185 178 207 52 F-OO1101M 25.
CRAFTSMAN 143.003502 KEY PART NO. NO. DESCRIPTION 0 RPM High 3050 to 3350 0 RPM Low 2400 to 2709 27625 Oil Fill Plug 29673 Oil Fill Plug Gasket 1 37289 Cylinder (Incl. 2,20 & 150) 2 26727 Dowel Pin 6 33734 Breather Element 7 36557 Breather Ass'y.
CRAFTSMAN 143.003502 151 31673 Valve Spring Cap 151A 40017 Intake Valve Seal 169 36783 Valve Cover Gasket 172 36784 Valve Cover 174 30200 Screw, 10-24 x 9/16" 178 29752 Nut & Lock Washer 179 .
CRAFTSMAN 143.003502 REPAIR PARTS (_20A 16 F-OO1101M 28.
CRAFTSMAN 143.003502 REPAIR PARTS KEY PART N0. NO. 0 640262 1 631615 2 631767 4 631184 5 631183 6 640070 7 650506 16 631807 17 651025 18 630766 20 640018 20A 640200 25 631867 27 631024 28 632019 29 631028 30 631021 31 631022 35 640259 36 640080 36A 632766 37 632547 40 640175 44 27110A 47 630748 48 631027 60 632760B DESCRIPTION Carburetor (Incl.
CRAFTSMAN 143.003502 REPAIR PARTS ]2 _3 ]] F-001101M KEY PART NO, NO. 0 590694 1 590599A 2 590600 3 590696 4 590601 5 590697 6 590698 7 590699 8 590700 11 590695 12 590535 13 590701 8 3 DESCRIPTION Recoil Starter Spring Pin (Incl. 4) Washer Retainer Washer Brake Spring Starter Dog Dog Spring Pulley & Rewind Spring Ass'y.
For the repair or replacement parts you need delivered directly to your home Call 7am-7pm, 7days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-859-7084 For.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Craftsman 536.772101 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Craftsman 536.772101 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Craftsman 536.772101 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Craftsman 536.772101 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Craftsman 536.772101, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Craftsman 536.772101.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Craftsman 536.772101. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Craftsman 536.772101 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
